Quadra-Fire SANTAFE-B1 Bedienungsanleitung

www.quadraﬁre.com 7001-142C November 2, 2005

SANTA FE PELLET STOVE

Owner’s Manual

Installation and Operation

SANTAFE-B1

Model:

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT.

CLOTHING IGNITION MAY RESULT.

WARNING

• Keep children away.

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high

temperatures.

• Do NOT operate with protective barriers open or

removed.

• Keep clothing, furniture, draperies and other

combustibles away.

Glass and other surfaces are hot

during operation and cool down.

DO NOT DISCARD THIS MANUAL

CAUTION

• Important operating and

maintenance instruc-

tions included.

• Leave this manual with

party responsible for use

and operation.

• Read, understand and

follow these instruc-

tions for safe installa-

tion and operation.

DO NOT

DISCARD

WARNING

Please read this entire manual

before installation and use of this

pellet fuel-burning room heater.

Failure to follow these instructions

could result in property damage,

bodily injury or even death.

• Do not store or use gasoline or other ﬂam-

mable vapors and liquids in the vicinity of this

or any other appliance.

• Do not overﬁre - If any external part starts to

glow, you are overﬁring. Reduce feed rate.

Overﬁring will void your warranty.

• Comply with all minimum clearances to com-

bustibles as speciﬁed. Failure to comply may

cause house ﬁre.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Consult local building, ﬁre ofﬁcials or authorities having

jurisdiction about restrictions, installation inspection,

and permits.

CAUTION

Tested and approved for wood pellets and shelled

ﬁeld corn fuel only. Burning of any other type of fuel

voids your warranty.

CAUTION

Tested and

Listed by

Beaverton

Oregon USA

OMNI- Test Laboratories, Inc .

Page 2 7001-142C November 2, 2005

Santa Fe Pellet Stove

Hearth & Home Technologies welcomes you to our tradi-

tion of excellence! In choosing a Quadra-Fire appliance,

you have our assurance of commitment to quality, durabil-

ity, and performance.

This commitment begins with our research of the market,

including ‘Voice of the Customer’ contacts, ensuring we

make products that will satisfy your needs. Our Research

and Development facility then employs the world’s most

advanced technology to achieve the optimum operation of

our stoves, inserts and ﬁreplaces. And yet we are old-

fashioned when it comes to craftsmanship. Each unit is

meticulously fabricated and gold and nickel surfaces are

hand-ﬁnished for lasting beauty and enjoyment. Our pledge

to quality is completed as each model undergoes a quality

control inspection. From design, to fabrication, to shipping:

Our guarantee of quality is more than a word, it’s Quadra-

Fire tradition, and we proudly back this tradition with a Lim-

ited Lifetime Warranty.

We wish you and your family many years of enjoyment in the

warmth and comfort of your hearth appliance. Thank you for

choosing Quadra-Fire.

With warm regards,

___________________________

Dave Fiebelkorn

Materials Manager

___________________________

Alan Trusler

SeniorVice President

Dealer Channel

___________________________

Dan Henry

Vice President

AdvancedTechnologies

_________________________

Jason Olmstead

Vice President &

General Manager

___________________________

Quadra-Fire Brand Manager

Steve Tate

SAMPLE: CLEARANCE TO COMBUSTIBLES LABEL

LOCATION: Back side of left side panel.

Listed Solid Fuel Room Heater/Pellet Type Insert.

Also suitable for Mobile Home

Installation. This appliance has been tested and listed for use in Manufactured Homes

in accordance with OAR 814-23-9000 through 814-23-909.

Tested to: ASTM E1509, ORD-C-1482-M199 0 Room Heating Pellet Burning Type,

APFI, (UM) 84-HUD FOR USE

ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN

FUEL.

Input Rating: 30,000 Btu's/hr

Electrical Rating:

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS .

Route power cord away from unit. Do not route cord under or in front of appliance.

DANGER:

Risk of electrical shock. Disconnect power supply before servicing. Replace

glass only with 5mm ceramic available from your dealer. To start, set thermostat above

room temperature, the stove will light automaticall y. To shutdown, set thermostat to below

room temperature. For further instruction refer to owner's manual.

Keep viewing and ash removal doors tightly closed during operation.

U.S. ENVIRONMENTAL PROTECTION AGENCY

This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].

2005 2006 2007 JAN FEB MAR APR MAY JUNE JU LY AUG SEPT OCT NOV DEC

7001-143

DO NOT REMOVE THIS LABEL / NEPAS ENLEVER L'ÉTIQUETTE

Made in U.S.A./Fait Aux États-Unis

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN, CLOTHING AND

FURNITUREAWAY. CONTACT MAY CAUSESKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.

Operatethis unit with fuel hopperlid closed.Failureto do so may result in emissionsproducts'combustionfrom the

hopper under certain conditions. Maintain hopper seal in good condition. Do no over fill the hopper.

ATTENTION:

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTSLOIN

DE L'ESPACE DÉSIGNÉDE L'INSTALLATION. LE CONTACT PEUT CAUSERDES BRÛLURESÀ LA PEAU. VOIR L'ÉTIQUETTE

ET LES INSTRUCTIONS.

Opérez cet appareil avec le couverclede la trémie fermé. Le défaut de ne pas suivre les instructionspeut résulter,

sous certaines conditions, en une combustion des émissions des produits venant de la trémie. Ne pas remplir la trémie trop pleine.

Testé à: ASTM E1509-95, ORD-C 1482-M1990 Room Heating. Pellet Burning Type, APFI, (UM)

84-HUD POUR USAGE AVEC LES BOULETTES DE BOIS OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ

DES CHAMPS.

Puissance de Rendement: 30,000 Btu's/hr

Puissance Électrique: 115 VAC, 60 Hz, Début 4.1 Amps, Courir 1.1 Amps,

Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil.

DANGER: Il y a risque de décharge électrique. Déconnectez le fil électrique de la prise de contact avant le

service.

Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseu r.

Pour allumer, monter la température du thermostat au dessus de la température de la pièce, le poêle s'allumera

automatiquement. Pour éteindre, descendre la température du thermostat en dessous de la température de la

pièce. Pour des instructions supplémentaires, référez vous au manuel du propriétaire. Gardez la porte

d'ouverture et la porte des cendres fermées hermétiquement durant l'opération.

Appareil de chauffage inséré de combustible solide/de type de boulettes. Accepté dans l'installation

dans les maisons mobiles. Cet appareil a été testé et enregistré pour l'usage dans les Maisons

Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.

1445 Highway North

Colville, WA 99 114

Manufactured by:Fabriqué par :

Listed by Beaverton

Oregon USA

OMNI-Test Laboratories, Inc.

Santa Fe Pellet Stove

Report /Rapport

061-S-53-2

SERIAL NO.

NUMÉRO DU

If Cas t Base is installe d (Part 811-0840 ) use a noncombustibl e floor

protecto r, extendin g beneat h heate r and to the front/sides/rea r as

indicated. Measure front distance (I) from the surface of the glass door. If

Cast Base is not installed, the non-combustible floor protector must be 1/4"

(6.4mm) minimum thickness ("k" value = 0.84).

G = 2"/51mm

H* = 2"/51mm

I = 6"/152mm

FLOOR PROTECTION / PROTECTION DU SOL

Non-combustible floor protection must extend beneath the flue pipe when

installed with horizontal venting or under the Top Vent Adapter with vertical

installation. RECOMMENDED IN USA; REQUIRED IN CANADA

Installezet utilizeretayagedu fonte (Pièce811-0840),le poêledoit être placésur une assisenon

combustibles’étendanttout autourde lui, commeles schémasl’indiquent. Mesurezla distancedu

devant (I) de la surface de la porte vitrée.

Ne pasinstallezétayagedufonte le protecteurde plancherdoitêtred'unminimumde 1/4"(6.4mm)

d'épaisseur, ('k" value = 0.84) de matériel incombustible ou équivalent.

*Un protecteur incombustiblede plancherdoit s'étendre sous le conduitde cheminée

pour une installation de ventilation horizontale ou sous un adapteur de ventilation de

dessus pour une installation verticale. ÉTATS-UNIS-RE COMMANDÉ ; CANAD A -

REQUIRENT.

www.quadrafire.co m

007

Manufactured

Date

Serial Number

Model Name

Test Lab &

Report No.

November 2, 2005 7001-142C Page 3

Santa Fe Pellet Stove

Section 1: Listing and Code Approvals

A. Appliance Certiﬁcations ......................4

B. Mobile Home Approved ......................4

C. Glass Speciﬁcations ............................4

D. Electrical Rating ..................................4

E. BTU & Efﬁciency Speciﬁcations ..........4

Section 2: Getting Started

A. Design, Installation & Location

Considerations ....................................5

B. Fire Safety ..........................................5

C. Tools & Supplies Needed ...................6

D. Measuring Standards .........................6

E. Inspect Appliance & Components

and Pre-Use Check List ......................6

Section 3: Dimensions & Clearances

A. Appliance Dimensions ........................7

B. Clearances to Combustibles ...............8

C. Hearth Requirements .........................9

Section 4: Vent Information

A. Chimney & Exhaust Connection .........10

B. Venting Termination Requirements ....10

C. Equivalent Feet of Pipe .......................11

D. Pipe Selection Chart ............................11

Section 5: Venting Systems

A. Alcove .................................................12

B. Through the Wall .................................13

C. Vertical ................................................14

D. Through the Wall & Vertical ................14

E. Masonry ..............................................15

F. Alternate Masonry ...............................15

Section 6: Mobile Home ..................................16

Section 7: Appliance Set-Up

A. Outside Air Kit .....................................17

B. Top Vent Adapter ................................18

C. Log Set Placement ..............................19

D. Grille & Trim Ring Installation .............20

E. Thermostat Installation ........................21

Section 8: Operating Instructions

A. Fuel Size & Material ............................22

B. General Operation Information ...........22

C. Before Your First Fire .........................23

D. Starting Your First Fire ........................23

E. Fire Characteristics .............................23

F. Feed Rate Adjustment .......................23

G. Ignition Cycles ....................................24

H. Frequently Asked Questions ..............24

Section 9: Troubleshooting ............................25-27

Section 10: Maintaining & Servicing Appliance

A. General Maintenance & Cleaning .......28-30

B. High Ash Fuel Content Maintenance ..31

C. Blower Replacement ...........................31

D. Igniter Replacement ............................32

E. Bafﬂe & Brick Removal .......................32

F. Bafﬂe & Brick Replacement ................33

G. Glass Replacement .............................34

Section 11: Reference Material

A. Component Functions ........................36-37

B. Component Locations .........................38

C. Exploded Drawings .............................39-40

D. Service Parts & Accessories ...............41-42

E. Warranty Policy ...................................43

F. Contact Information .............................44

TABLE OF CONTENTS

Page 4 7001-142C November 2, 2005

Santa Fe Pellet Stove

1Listing and Code Approvals

Model: Santa Fe Pellet Stove

Laboratory: OMNI Test Laboratories, Inc.

Report No. 061-S-53-2

Type: Solid Fuel Room Heater/Pellet Type

Standard: ASTM E1509 and ULC/ORD-C1482

Room Heater Pellet Fuel Burning type

and (UM) 84-HUD, Mobile Home

Approved.

A. Appliance Certiﬁcation

C. Glass Speciﬁcations

E. BTU & Efﬁciency Speciﬁcations

This appliance is equipped with 5mm ceramic glass. Replace

glass only with 5mm ceramic glass. Please contact your

dealer for replacement glass.

This appliance is approved for mobile home installations

when not installed in a sleeping room and when an outside

combustion air inlet is provided. The structural integrity of

the mobile home ﬂoor, ceiling, and walls must be maintained.

The appliance must be properly grounded to the frame of

the mobile home and use only listed pellet vent Class “L” or

“PL” connector pipe. A Quadra-Fire Outside Air Kit must be

installed in a mobile home installation.

B. Mobile Home Approved

NOTE: This installation must conform with local codes.

In the absence of local codes you must comply with the

ASTM E1509, (UM) 84-HUD, ULC/ORD-C-1482

D. Electrical Rating

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps

*BTU output will vary, depending on the brand of fuel you

use in your stove. Consult your Quadra-Fire dealer for

best results.

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products,

their speciﬁcations and/or price without notice.

Particulate Emis-

sions Rating: 0.7 grams/hr

*BTU Output: 8,000 - 30,000 / hr

Heating Capacity: up to 1,500 sq. ft.

Hopper Capacity: 52 lbs

Fuel: Wood Pellets or Shelled Corn

Shipping Weight: 240 lbs

November 2, 2005 7001-142C Page 5

Santa Fe Pellet Stove

2Getting Started

. Design, Installation & Location

Considerations

1. Appliance Location

Consideration must be given to safety, convenience, trafﬁc

ﬂow, and the fact that the appliance will need a chimney and

chimney connector. It is a good idea to plan your installation

on paper, using exact measurements for clearances and

ﬂoor protection, before actually beginning the installation. If

you are not using an existing chimney, place the appliance

where there will be a clear passage for a factory-built listed

chimney through the ceiling and roof.

Check with your local building code agency before you

begin your installation. Be sure local building codes do not

supersede UL speciﬁcations and always obtain a building

permit so that insurance protection benefits cannot be

unexpectedly cancelled. If any assistance is required during

installation, please contact your local dealer.

We recommend that a qualiﬁed building inspector and your

insurance company representative review your plans before

and after installation.

2. Thermostat Location

The thermostat’s location will have some effect on the

appliance’s operation. When the thermostat is located close

to the appliance, it may require a slightly higher temperature

setting to keep the rest of the house comfortable. If the

thermostat location is in an adjacent room or on a different

ﬂoor level, you will notice higher temperatures near the

appliance.

B. Fire Safety

Maintain the designated clearances to combustibles.

Insulation must not touch the chimney. You must maintain

the designated air space clearance around the chimney.

This space around a chimney is necessary to allow

natural heat removal from the area. Insulation in this

space will cause a heat buildup, which may ignite wood

framing. NOTE: Clearances may only be reduced by

means approved by the regulatory authority having

jurisdiction.

To provide reasonable ﬁre safety, the following should be

given serious consideration:

1. Install at least one smoke detector on each ﬂoor of

your home to ensure your safety. They should be

located away from the heating appliance and close

to the sleeping areas. Follow the smoke detector

manufacturer’s placement and installation instructions,

and be sure to maintain regularly.

2. A conveniently located Class A fire extinguisher

to contend with small fires resulting from burning

embers.

3. A practiced evacuation plan, consisting of at least

2 escape routes.

4. A plan to deal with a hopper ﬁre as follows:

In the event of a hopper ﬁre:

A. Notify ﬁre department

B. Prepare occupants for immediate evacuation.

C. Close all openings into the appliance.

D. While awaiting ﬁre department, watch for ignition

of adjacent combustibles from overheated vent

pipe, hot embers or sparks from the chimney.

E. Pour a bucket of water into the appliance

hopper.

CAUTION

• Do NOT connect this unit to a chimney ﬂue servicing

another appliance.

• Do NOT connect to any air distributon duct or system. Fire Hazard.

WARNING

• Do not operate appliance before reading

and understanding operating instructions.

• Failure to operate appliance properly may

cause a house ﬁre.

Page 6 7001-142C November 2, 2005

Santa Fe Pellet Stove

E. Inspect Appliance & Components and

Pre-Use Check List

Reciprocating Saw

Channel Locks

Hammer

Phillips Screwdriver

Tape Meausre

Plumb Line

Level

Framing Material

Hi-temp Caulking Material

Gloves

Safety Glasses

Framing Square

Electric Drill & Bits (1/4”)

1/4” Self-Tapping Screws

May also need:

Vent Support Straps

Venting Paint

Tools and building supplies normally required

for installation, unless installing into an existing

masonry ﬁreplace:

C. Tools And Supplies Needed

Inspect appliance and components for

damage. Damaged parts may impair safe

operation.

WARNING

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

• Installation and use of any damaged appliance.

• Modiﬁcation of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

• Operating appliance without fully assembling all

components.

• Operating appliance without legs attached (if supplied

with unit).

• Do NOT Overﬁre -

Or any such action that may cause a ﬁre hazard.

WARNING

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

D. Measuring Standards

1. Pipe measurements are from center line to center line.

2. Vertial terminations are measured to top of pipe.

Figure 6.1

Measure horizontal

clearances from

this surface

Measure vertical

clearances from

this surface

1. Place the appliance in a location near the

ﬁnal installation area and follow the proce-

dures below:

2. Open the appliance and remove all the parts

and articles packed inside the Component

Pack. Inspect all the parts and glass for ship-

ping damage. Contact your dealer if any irregu-

larities are noticed.

3. All safety warnings have been read and fol-

lowed.

4. This Owner’s Manual has been read.

5. Floor protection requirements have been met.

6. Venting is properly installed.

7. The proper clearances from the appliance and

chimney to combustible materials have been

met.

8. The masonry chimney is inspected by a profes-

sional and is clean, or the factory built metal

chimney is installed according to the manufac-

turer’s instructions and clearances.

9. The chimney meets the required minimum

height.

10.

All labels have been removed from the glass

door.

11. Plated surfaces have been wiped clean, if

applicable.

12. Thermostat or remote has been installed.

13. A power outlet is available nearby.

November 2, 2005 7001-142C Page 7

Santa Fe Pellet Stove

3Dimensions and Clearances

A. Appliance Dimensions

Figure 7.2- Front View

Figure 7.1 - Top View

Figure 7.3 -Side View Figure 7.4 - Side View with Top Vent Adapter

25-7/16 in.

(705 mm)

12-11/16 in.

(322mm)

21-3/16 in.

(538mm)

27-3/4 in.

(705mm)

28-5/8 in.

with base

(727mm with

base)

16-7/16 in.

(418mm)

17-5/16 in.

with base

(440mm)

28-9/16 in

(726mm)

26-7/16 in

(672mm)

25-13/16 in (655mm)

28-3/16 in (716mm)

3-7/8 in

(98mm) 2-5/8 in

(66mm)

Page 8 7001-142C November 2, 2005

Santa Fe Pellet Stove

Straight Back Against

Wall

Inches Millimeters

ABack Wall to Appliance 2 51

BSide Wall to Appliance 6 152

Corner Installation Inches Millimeters

CWalls to Appliance 2 51

Vertical Installation Inches Millimeters

DBack Wall to Flue Pipe 3 76

ESide Wall to Cast Top 6 152

FBack Wall to Appliance 7 178

Installations with:

3 to 3 inch Top Vent Adapter and

3 to 6 inch Offset Adapter Kit

Corner Installation Inches Millimeters

GWalls to Appliance 2 51

HSide Wall to Flue Pipe 3 76

Alcove Installation Inches Millimeters

Minimum Alcove Height 43 1092

Minimum Alcove Side Wall 6 152

Minimum Alcove Width 38 965

Maximum Alcove Depth 36 914

Dimension to Corner Inches Millimeters

IFlue Center Line 10-3/8 264

JBack of Top Vent Adapter 9-1/8 232

B. Clearances to Combustibles (UL and ULC)

Fire Risk.

Comply with all minimum clearances to

combustibles as speciﬁed.

WARNING

Failure to comply may cause house ﬁre.

NOTE:

• Illustrations reﬂect typical installations and are FOR

DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design

preference.

November 2, 2005 7001-142C Page 9

Santa Fe Pellet Stove

*L Exception for Horizontal Installations:

USA INSTALLATIONS: If optional Cast Base is installed use

a noncombustible ﬂoor protector extending under unit and to

the sides, front and back of unit as shown in Floor Protection

Diagram. Measure front distance (M) from the surface of the

glass door.

If Cast Base is not installed, the noncombustible ﬂoor protector

must be 1/4 inch (6mm) minimum thickness (“k” value = 0.84).

noncombustible ﬂoor protection extending beneath the

ﬂue pipe is recommended

with horizontal venting or under

the top vent adapter with vertical installation. See Figure

9.2

CANADA INSTALLATIONS: A

noncombustible ﬂoor pro-

tection extending beneath the ﬂue pipe is r

equired

with

horizontal venting or under the top vent adapter with vertical

installation.

Must extend 2 inches (51mm) beyond each

side of pipe (shaded area)

C. Hearth Pad Requirements (UL and ULC)

Use a noncombustible ﬂoor protector, extending beneath

appliance and to the front, sides and rear as indicated.

Measure front distance “M” from the surface of the glass

door.

Hearth Pad Requirements Inches Millimeters

KSides 2 51

L* Back 2 51

MFront 6 152

Figure 9.2

Figure 9.1

Page 10 7001-142C November 2, 2005

Santa Fe Pellet Stove

Do not terminate vent in any enclosed or semi-enclosed

area such as a carport, garage, attic, crawl space, under a

sun deck or porch, narrow walkway or closely fenced area,

or any location that can build up a concentration of fumes

such as a stairwell, covered breezeway, etc.

CAUTION

Vent surfaces get HOT, can cause burns if

touched. Noncombustible shielding or guards

may be required.

WARNING

A. Chimney and Exhaust Connection

1. Chimney & Connector: Use 3 or 4 inch (76-102mm)

diameter type "L" or "PL" venting system. It can be

vented vertically or horizontally.

2. Mobile Home: Approved for all listed pellet vent. If

using the 3 inch (76mm) vertical Top Vent Adapter Kit

or the 3 to 6 inch (76-152mm) Top Vent Offset Adapter,

use listed double wall ﬂue connector. A Quadra-Fire

Outside Air Kit must be used with manufactured home

installations.

3. Residential: The 3 inch (76mm) vertical Top Vent

Adapter Kit and the 3 to 6 inch (76-152mm) Top Vent

Offset Adapter are tested to use 24 gauge single wall

ﬂue connector or listed double wall ﬂue connector to

Class A listed metal chimneys, or masonry chimneys

meeting Internationalt Conference of Building Ofﬁcials

(ICBO )standards for solid fuel appliances.

4. INSTALL VENT AT CLEARANCES SPECIFIED BY THE

VENT MANUFACTURER.

5. Secure exhaust venting system to the appliance with at

least 3 screws. Also secure all connector pipe joints with

at least 3 screws through each joint.

NOTE: All pipe must be welded seam pipe whenever

possible. Seal pipe joints with high temperature silicone

(500°F [260°C] minimum rated only).

NOTE: If burning shelled ﬁeld corn, you must use

approved venting speciﬁcally designed for corn. Follow

the instructions from the venting manufacturer.

Fire Hazard.

• Only LISTED venting components may be

used.

• NO OTHER vent components may be used.

Substitute or damaged vent components may

impair safe operation.

WARNING

B. Venting Termination Requirements

1. Termination must exhaust above air inlet elevation. It is

recommended that at least 60 inches (1524mm) of verti-

cal pipe be installed when appliance is vented directly

through a wall. This will create a natural draft, which will

help prevent the possibility of smoke or odor venting into

the home during a power outage. It will also keep exhaust

from causing a nuisance or hazard by exposing people or

shrubs to high temperatures. The safest and preferred

venting method is to extend the vent vertically through the

roof.

2. Distance from doors and opening windows, or gravity or

ventilation air inlets into building:

a. Not less than 48 inches (1219mm) below;

b. Not less than 48 inches (1219mm) horizontally from;

c. Not less than 12 inches (305mm) above.

3. Distance from permanently closed windows:,

a. Not less than 12 inches (305) below; horizonatlly from

or above.

4. Distance between bottom of termination and grade should

be 24 inches (610mm) minimum. This is conditional upon

plants in the area, and nature of grade surface. The grade

surface must be a noncombustible material (i.e., rock, dirt).

The grade surface must not be lawn. Distance between

bottom of termination and public walkway should be 84

inches (2134mm) minimum.

5. Distance to combustible materials must be 24 inches

(610mm) minimum. This includes adjacent buildings,

fences, protruding parts of the structure, roof overhang,

plants and shrubs, etc.

6. Termination Cap Location (Home Electrical Service)

• Side-to-side clearance is to be the same as minimum

clearance to vinyl inside corners.

• Clearance of a termination cap below electrical service

shall be the same as minimum clearance to vinyl sof-

ﬁts.

• Clearance of a termination cap above electrical service

will be 12 inches minimum.

• Location of the vent termination must not obstruct or

interfere with access to the electrical service.

4Vent Information

Andere Handbücher für SANTAFE-B1

Inhaltsverzeichnis

Andere Quadra-Fire Pelletofen Handbücher

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVERNON-AE-CSB Bedienungsanleitung

Quadra-Fire

Quadra-Fire SANTAFE-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVERNINSAE-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Sicherheitsleitfaden

Quadra-Fire

Quadra-Fire CB1200-I Pellet Insert CB1200I-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Quadra-Fire

Quadra-Fire SANTA FE SANTAFE-C Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire SANTAFEI-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Quadra-Fire

Quadra-Fire SANTAFEI-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVERNINSAE-PMH Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire TREKKER INSERT series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire CASTILEI-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK-C Bedienungsanleitung

Quadra-Fire

Quadra-Fire CASTILE-CWL-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Sicherheitsleitfaden

Quadra-Fire

Quadra-Fire SANTAFE-MBK Sicherheitsleitfaden

Quadra-Fire

Quadra-Fire MT VERNON Pellet Insert Advanced Energy (AE)... Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung

United States Stove

United States Stove American Harvest 6039 Bedienungsanleitung

Extraflame

Extraflame DUCHESSA IDRO Bedienungsanleitung

SMG

SMG ComfortBilt HP21 Bedienungsanleitung

Enviro

Enviro Empress-A-FS Bedienungsanleitung