Quantum Atlas II Service-Handbuch

Atlas II

Jumper Settings

50-pin Jumper Settings

Jumper Settings

The following describes the jumper options and settings available on the Maxtor® Atlas™ II disk drive.

Maxtor Atlas II was developed by Quantum Corporation prior to its merger with Maxtor.

Termination Enable (TE)

Enable termination TE jumper on

Disable termination TE jumper off

1 of 8

Atlas II

Jumper Settings

Termination Power (TP)

Enable termination power TP jumper on

Disable termination power TP jumper off

SCSI ID (A3, A2, A1, A0)

Set drive SCSI ID See ID settings table below

Delay Spin (DS)

Enable spin delay

SP jumper off

Disable spin delay

SP jumper on

cStagger Spin

Enable spin stagger SS jumper on

Disable spin stagger SS jumper off

Write Protect

Enable W

rite Protection WP jumper on

Disable W

rite Protection WP jumper off

Jumper Locations

The Atlas II disk drive has two locations where user configurable jumpers are found. The primary jumper block (Front option

connector J3) for the Atlas II is found on the front edge of the disk drive printed circuit board. Using these jumper pins you

can establish the various drive configuration options. The second option jumper block is used to set the Atlas II termination

options. This jumper block is found on the printed circuit board at the rear of the drive and is near the SCSI cable connector.

2 of 8

Atlas II

Jumper Settings

28-Pin Secondary Option Connector

ignal P

in S

ignal

logic_gnd

Fault LED

key (blank)

Busy LED

0 Spindle Sync

+5VDC out

2 unused

Delay Spin

4 logic_gnd

Stagger Spin

6 logic_gnd

Write Protect

8 logic_gnd

Spindle Sync

0 logic_gn

The drawing above displays the jumper block physical location and pin definitions.

3 of 8

Atlas II

Jumper Settings

SCSI ID Settings

The following table identifies the various SCSI ID values and the jumper positions required to set them.

Drive ID

ID 0

OFF

ID 1

OFF

ID 2

OFF

ID 3

OFF

ID 4

OFF

ID 5

OFF

ID 6

OFF

ID 7

4 of 8

Atlas II

Jumper Settings

68-pin Jumper Settings

Jumper Settings

The following describes the jumper options and settings available on the Maxtor® Atlas™ II disk drive. Maxtor Atlas II was

developed by Quantum Corporation prior to its merger with Maxtor.

Termination Enable (TE)

Enable termination TE jumper on

Disable termination TE jumper off

Note: Termination enable available on SE version only.

Termination Power (TP)

Enable termination power TP jumper on

Disable termination power TP jumper off

SCSI ID (A3, A2, A1, A0)

Set drive SCSI ID See ID settings table below

Delay Spin (DS)

Enable spin delay

Disable spin delay

SP jumper off

SP jumper on

5 of 8

Atlas II

Jumper Settings

6 of 8

Stagger Spin

Enable spin stagger SS jumper on

Disable spin stagger SS jumper off

Write Protect

Enable Write Protection

WP jumper on

Disable W

rite Protection WP jumper off

Jumper Locations

The Atlas II wide disk drive has two locations where user configurable jumpers are found. The primary jumper block (Front

option connector J3) for the Atlas II wide is found on the front edge of the disk drive printed circuit board. Using these

jumper pins you can establish the various drive configuration options. The secondary option jumper block provides an

alternate method for setting primary drive features. The alternate jumper block is located at the rear of the drive and is

incorporated into the SCSI cable connector.

The termination power option setting is located on the front edge of the printed circuit board and is adjacent to the J3

connector.

Atlas II

Jumper Settings

7 of 8

Signal

ogic_gnd

Key

(blank) 1

0 F

ault LED

Delay

Spin 1

2 l

ogic_gnd

Logic ground

4 E

nable Active Termination

Spindle Sync

6 S

pindle Sync

Busy Led

8 +

5VDC out

rite Protect 2

0 l

ogic_gnd

Stagger Spin

2 l

ogic_gnd

Enabl

e Narrow Mode 2

4 l

ogic_gnd

Disable Sync Negotiation

6 l

ogic_gnd

Disable SCSI Parity

8 l

ogic_gnd

Disable Unit Attentio

n 3

0 l

ogic_gnd

Customize

2 l

ogic_gnd

Signal

in S

ignal

ault LED

ogic_gnd

usy LED

Enable Ter

mination 1

0 l

ogic_gnd

+5VDC out

2 (

reserved)

Note: Enable Termination setting is not supported on the following differential drives:

Atlas II 2.2GB WD

Atlas II 4.5GB WD

Atlas II

Jumper Settings

Atlas II 9.1GB WD SCSI ID SettingsThe following table identifies the various SCSI ID values and the jumper positions

required to set them.

Drive ID

ID 0

OFF

ID 1

OFF

ID 2

OFF

ID 3

OFF

ID 4

OFF

ID 5

OFF

ID 6

OFF

ID 7

OFF

ID 8

OFF

ID 9

OFF

ID 10

OFF

ID 11

OFF

ID 12

OFF

ID 13

OFF

ID 14

OFF

ID 15

8 of 8

Inhaltsverzeichnis

Andere Quantum Lagerung Handbücher

Quantum

Quantum Scalar LTFS Gebrauchs- und Pflegehandbuch

Quantum

Quantum Tape Drives A-Series Bedienungsanleitung

Quantum

Quantum ACL 4/52 Handbuch

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum Scalar i500 Bedienungsanleitung

Quantum

Quantum SNC 5100 Bedienungsanleitung

Quantum

Quantum ValueLoader LTO-2 Bedienungsanleitung

Quantum

Quantum LTO 3 Bedienungsanleitung

Quantum

Quantum DLTtape DLT1 Bedienungsanleitung

Quantum

Quantum SNC 4500 Bedienungsanleitung

Quantum

Quantum FIREBALL PLUS AS 10.2 Bedienungsanleitung

Quantum

Quantum Scalar i40 Bedienungs- und Sicherheitshinweise

Quantum

Quantum Scalar i40 Bedienungs- und Sicherheitshinweise

Quantum

Quantum Scalar 50 Bedienungsanleitung

Quantum

Quantum DLTtape DLT 2000 Handbuch

Quantum

Quantum P4000 Series Bedienungsanleitung

Quantum

Quantum ActiveScale X100 Bedienungsanleitung

Quantum

Quantum LTO-3 Bedienungsanleitung

Quantum

Quantum Maxtor Fireball CR Bedienungsanleitung

Quantum

Quantum DXi4700 Installations- und Betriebshandbuch

Quantum

Quantum DLT-V4 Bedienungsanleitung

Quantum

Quantum SuperLoader DLT Bedienungsanleitung

Quantum

Quantum Lattus A10 Bedienungsanleitung

Quantum

Quantum DLTtape SDLT 600 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung