Radio Shack ET-916 Bedienungsanleitung

Cat. No. 43-1086

OWNER’S MANUAL

Please read before using this equipment.

ET-916

900-MHz Extended-Range Cordless Telephone

with 10-Number Memory

43-1086.fm Page 1 Tuesday, August 17, 1999 2:39 PM

FEATURES

COM-LOK is a registered trademark used by Tandy Corporation.

RadioShack is a trademark used by Tandy Corporation.

Your RadioShack ET-916 900-MHz

Extended-Range Cordless Telephone

with 10-Number Memory uses the 900

MHz band which means less interfer-

ence, clearer sound, and greater range

than 46/49 MHz cordless telephones.

The ET-916’s features include:

900 MHz Operation — provides bet-

ter sound and less interference than

many other cordless phones.

40 Channels — automatically selects

a clear channel when you make or an-

swer a call. You can also manually

change channels during a call.

Super CCT Noise-Reduction Cir-

cuitr

— provides clear telephone

conversations, giving you sound clarity

comparable to that of a corded phone.

Securit

Access-Protection Code —

automatically prevents other cordless

phone users from using your phone

line while the handset is off the cradle.

COM-LOK®— ensures that other

cordless phone users cannot use your

phone line when the handset is on the

cradle.

Redial — lets you quickly redial the

last number dialed.

10-Number Memor

Dialin

— lets

you store up to 10 numbers in memory

for easy dialing.

e— lets you send a paging signal

from the base to the handset to page

someone or locate the handset if you

misplace it.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Volume Control — lets you adjust

the volume you hear through the

handset.

Pro

rammable Rin

er — lets you

select from four ringer tone/volume

settings.

Tone/Pulse Dialin

— lets you use

your phone with tone or pulse service.

Quick Talk — lets you make or an-

swer a call by just lifting the handset

from the base.

Hearin

-Aid Compatibilit

— lets

you use your phone with hearing aids

that have a T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

43-1086.fm Page 2 Tuesday, August 17, 1999 2:39 PM

Important Note: Cordless phones

such as this one require AC power to

operate. When the AC power is off,

you cannot dial out or receive incoming

calls using your ET-916. To be safe,

you should also have a phone that

does not need AC power to operate

(not a cordless phone) so you can still

make and receive calls if there is an

AC power failure.

We recommend you record your

phone’s serial number here. The num-

ber is on the bottom of the base.

Serial Number __________________

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

CAUTION !

Warning: To prevent fire or shock haz-

ard, do not expose this product to rain

or moisture.

READ THIS BEFORE

INSTALLATION

Each device that you connect to the

phone line draws power from the

phone line. We refer to this power draw

as the device’s

ringer equivalence

number

, or REN. The REN is shown

on the bottom of the base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phones might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are located

on the bottom of the base.

Note: You must not connect your

phone to any of the following:

• coin-operated systems

• party-line systems

• most electronic key phone sys-

tems

43-1086.fm Page 3 Tuesday, August 17, 1999 2:39 PM

CONTENTS

Installation ............................................................................................................ 5

Selecting a Location ........................................................................................ 5

Placing the Base on a Desk Top ............................................................... 5

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 8

Connecting and Charging the Battery Pack .................................................... 9

Setting the Dialing Mode ............................................................................... 11

Setting the Ringer Tone/Volume .................................................................... 11

Operation ............................................................................................................ 12

Making and Receiving Calls .......................................................................... 12

Selecting the Channel ................................................................................... 12

Setting the Handset Volume .......................................................................... 12

Using REDIAL ............................................................................................... 12

Using FLASH ................................................................................................. 13

Using Tone Services on a Pulse Line ............................................................ 13

Paging ........................................................................................................... 14

Memory Dialing .............................................................................................. 14

Storing a Number in Memory .................................................................. 14

Entering a Pause .................................................................................... 15

Dialing a Memory Number ...................................................................... 15

Chain-Dialing Service Numbers .............................................................. 15

Testing Stored Emergency Numbers ...................................................... 15

Troubleshootin

................................................................................................. 16

Care and Maintenance ....................................................................................... 18

Replacing the Battery Pack ........................................................................... 19

The FCC Wants You to Know ........................................................................ 20

Lightning ........................................................................................................ 20

43-1086.fm Page 4 Tuesday, August 17, 1999 2:39 PM

INSTALLATION

SELECTING A

LOCATION

You can place the phone on a desktop

or table, or mount it on a wall. Select a

location that is:

• near an AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls

or filing cabinets, wireless inter-

coms, alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of

several locations, try each to see

which provides the best performance.

Caution: The supplied RadioShack

AC adapter was designed specifically

for your ET-916. Use only the supplied

adapter.

Notes:

• Your telephone connects directly

to a modular telephone line jack. If

your phone line jack is not a mod-

ular jack, you can update the wir-

ing yourself, using jacks and

adapters available at your local

RadioShack store. Or, you can let

the phone company update the

wiring for you.

• The phone company will charge

you for the installation of neces-

sary jacks.

• The USOC number of the jack to

be installed is RJ11C (RJ11W if

you want to mount it on a wall

plate).

Placing the Base on a

Desk Top

Follow these steps when you place the

base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the TEL.LINE

jack on the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

43-1086.fm Page 5 Tuesday, August 17, 1999 2:39 PM

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

4. Route the adapter’s cord through

the strain relief slot on top of the

base.

5. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

6. Lift the base’s antenna to a verti-

cal position.

Strain Relief Slot

Mounting the Base on a

Wall Plate

1. Plug one end of the supplied short

modular cord into the TEL.LINE

jack on the back of the base.

2. Route the modular cord through

the right slots on the bottom of the

base.

43-1086.fm Page 6 Tuesday, August 17, 1999 2:39 PM

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

4. Route the adapter’s cord through

the slot on top of the base and

through the left slots on the bot-

tom of the base.

5. Plug the short modular cord into

the wall plate jack.

6. Align the base’s keyhole slots with

the wall plate studs and slide the

base downward to secure it.

7. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the

handset.

8. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

9. Lift the base’s antenna to a verti-

cal position.

43-1086.fm Page 7 Tuesday, August 17, 1999 2:39 PM

Mounting the Base Directly

on the Wall

For this mounting method, you need

two flat-head wood screws (not sup-

plied) with heads that fit into the key-

hole slots on the bottom of the base.

1. Drill two holes 35/16

inches apart. Then

thread a screw into

each hole, letting the

heads extend about

3/16 inch from the

wall.

2. Plug one end of the supplied mod-

ular cord into the TEL.LINE jack on

the back of the base.

3. Route the modular cord through

the right slots on the bottom of the

base.

3/16

35/16

4. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

5. Route the adapter’s cord through

the slot on top of the base and

through the left slots on the bot-

tom of the base.

6. Align the keyhole slots with the

mounting screws and slide the

base downward to secure it.

7. Plug the modular cord into a mod-

ular phone line jack.

43-1086.fm Page 8 Tuesday, August 17, 1999 2:39 PM

8. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the

handset.

9. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

10. Lift the base’s antenna to a verti-

cal position.

CONNECTING AND

CHARGING THE

BATTERY PACK

The ET-916 comes with a recharge-

able nickel-cadmium battery pack in

the handset. Before using your phone,

you must connect the battery pack and

then charge it for about 14 hours.

1. Loosen the screw on the battery

compartment cover on the bottom

of the handset. Press down and

slide off the compartment cover in

the direction of the arrow.

2. Insert the battery pack’s plastic

connector into its socket. The plug

fits only one way.

Note: For easier battery pack con-

nection, lift it out of the compart-

ment, insert its connector into its

socket and replace the battery

pack inside the compartment.

3. Replace the cover and tighten the

screw.

To charge the battery pack, simply

place the handset on the base. The

CHARGE indicator on the base lights.

Recharge the battery pack when the

TALK/BATT LOW indicator flashes.

CHARGE Indicator

43-1086.fm Page 9 Tuesday, August 17, 1999 2:39 PM

Notes:

• If the CHARGE indicator does not

light when you place the handset

on the base, be sure the battery

pack and AC adapter are correctly

and securely connected.

Also, check the charging contacts

on the handset and the base. If

the contacts are dirty or tarnished,

clean them with a pencil eraser.

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work

and you might hear an error tone.

If this happens, return the handset

to the base for a few seconds.

• About once a month, fully dis-

charge the battery pack by keep-

ing the handset off the base until

the TALK/BATT LOW indicator

flashes. Otherwise, the battery

pack loses its ability to fully re-

charge.

• If the TALK/BATT LOW indicator

does not light but the phone does

not work, recharge the battery

pack. (The battery power might be

too low to light the indicator.)

• If the battery pack becomes weak

during a call, you hear a beep ev-

ery 30 seconds and the TALK/

BATT LOW indicator flashes ev-

ery 3 seconds. Recharge the bat-

tery pack.

• If the battery pack is completely

discharged, the handset loses the

security access-protection code.

To reset the code, place the hand-

set on the base and charge the

battery pack.

• The supplied battery pack should

last for about a year. When the

battery pack loses its ability to

fully recharge, order a replace-

ment battery pack from your local

RadioShack store (see “Replacing

the Battery Pack” on Page 19).

43-1086.fm Page 10 Tuesday, August 17, 1999 2:39 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3827 Bedienungsanleitung

Radio Shack

Radio Shack Wireless Phone Jack System Bedienungsanleitung

Radio Shack

Radio Shack TAD-1015 Bedienungsanleitung

Radio Shack

Radio Shack TAD-727 Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Radio Shack

Radio Shack 43-3571 Bedienungsanleitung

Radio Shack

Radio Shack 43-3812 Bedienungsanleitung

Radio Shack

Radio Shack Two-Line Caller ID Phone With Speakerphone Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Radio Shack

Radio Shack 2-Line 900 MHz Handsfree Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack ET-537 Bedienungsanleitung

Radio Shack

Radio Shack TAD-729 Bedienungsanleitung

Radio Shack

Radio Shack 43-143 Bedienungsanleitung

Radio Shack

Radio Shack 4301122D Bedienungsanleitung

Radio Shack

Radio Shack 43-3817 Bedienungsanleitung

Radio Shack

Radio Shack Caller ID System 1500 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Telephone Bedienungsanleitung

Radio Shack

Radio Shack 43-1088 Bedienungsanleitung

Radio Shack

Radio Shack ET-548 Bedienungsanleitung

Radio Shack

Radio Shack ET-1109 Bedienungsanleitung

Radio Shack

Radio Shack 43-3548 Bedienungsanleitung

Radio Shack

Radio Shack 43-3548 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3580 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung