Radio Shack 43-1088 Bedienungsanleitung

Cat. No. 43-1088/1090

OWNER’S MANUAL

Please read before using this equipment.

900-MHz Cordless Telephone

with Headset Jack

ET-918White(43-1088)

ET-920 Black(43-1090)

43-1088_90.fm Page 1 Tuesday, August 17, 1999 2:57 PM

FEATURES

COM-LOK and RadioShack are registered trademarks used by Tandy Corporation.

Your RadioShack ET-918/920 900-

MHz Cordless Telephone with Head-

set Jack uses the 900 MHz band which

means less interference, clearer

sound, and greater range than 46/49

MHz cordless telephones.

And, its headset jack means you can

connect an optional headset for hands-

free convenience while you use the

phone.

The phone’s other features include:

900 MHz Operation — provides long-

er range and less interference than

many other cordless phones.

40 Channels — automatically selects

a clear channel when you make or an-

swer a call. You can also manually

change channels during a call.

Super CCT Noise-Reduction Cir-

cuitr

— provides clear telephone

conversations, giving you sound clarity

comparable to that of a corded phone.

Securit

Access-Protection Code —

automatically prevents other cordless

phone users from using your phone

line while the handset is off the base.

COM-LOK®— ensures that other

cordless phone users cannot use your

phone line when the handset is on the

base.

Redial — lets you quickly redial the

last number dialed.

10-Number Memor

Dialin

— lets

you store up to 10 numbers in memory

for easy dialing.

e— lets you send a paging signal

from the base to the handset to page

someone or locate the handset if you

misplace it.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Volume Control — lets you adjust

the volume you hear through the

handset.

Pro

rammable Rin

er — lets you

select from four ringer tone/volume

settings.

Tone/Pulse Dialin

— lets you use

your phone with tone or pulse service.

Quick Talk — lets you make or an-

swer a call by just lifting the handset

from the base.

Hearin

-Aid Compatibilit

— lets

you use your phone with hearing aids

that have a T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

43-1088_90.fm Page 2 Tuesday, August 17, 1999 2:57 PM

Important Note: Cordless phones

such as this one require AC power to

operate. When the AC power is off,

you cannot dial out or receive incoming

calls using your phone. To be safe, you

should also have a phone that does

not need AC power to operate (not a

cordless phone) so you can still make

and receive calls if there is an AC pow-

er failure.

We recommend you record your

phone’s serial number here. The num-

ber is on the bottom of the base.

Serial Number __________________

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warning: To reduce the risk of fire

or shock hazard, do not expose

this product to rain or moisture.

CAUTION !

READ THIS BEFORE

INSTALLATION

Each device that you connect to the

phone line draws power from the

phone line. We refer to this power draw

as the device’s

ringer equivalence

number

, or

REN

. The REN is on the

bottom of the base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phones might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are on the

bottom of the base.

Note: You must not connect your

phone to any of the following:

• coin-operated systems

• party-line systems

• most electronic key phone sys-

tems

43-1088_90.fm Page 3 Tuesday, August 17, 1999 2:57 PM

CONTENTS

Installation ............................................................................................................ 5

Selecting a Location ........................................................................................ 5

Placing the Base on a Desk Top ............................................................... 5

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 7

Connecting and Charging the Battery Pack .................................................... 9

Setting the Dialing Mode ............................................................................... 11

Setting the Ringer Tone/Volume .................................................................... 11

Operation ............................................................................................................ 12

Making and Receiving Calls .......................................................................... 12

Selecting the Channel ................................................................................... 12

Setting the Handset Volume .......................................................................... 12

Using REDIAL ............................................................................................... 12

Using FLASH ................................................................................................. 13

Using Tone Services on a Pulse Line ............................................................ 13

Paging ........................................................................................................... 14

Memory Dialing .............................................................................................. 14

Storing a Number in Memory .................................................................. 14

Entering a Pause .................................................................................... 15

Dialing a Memory Number ...................................................................... 15

Chain-Dialing Service Numbers .............................................................. 16

Testing Stored Emergency Numbers ...................................................... 16

Using a Headset ............................................................................................ 16

Troubleshootin

................................................................................................. 17

Care and Maintenance ....................................................................................... 19

Replacing the Battery Pack ........................................................................... 20

The FCC Wants You to Know ........................................................................ 21

Lightning ........................................................................................................ 21

43-1088_90.fm Page 4 Tuesday, August 17, 1999 2:57 PM

INSTALLATION

SELECTING A

LOCATION

You can place the phone’s base on a

desk top or table, or mount it on a wall.

Select a location that is:

• near an AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls

or filing cabinets, wireless inter-

coms, alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of

several locations, try each to see

which provides the best performance.

Caution: The supplied RadioShack

AC adapter was designed specifically

for your ET-918/920. Use only the sup-

plied adapter.

Notes:

• Your telephone connects directly

to a modular telephone line jack. If

your phone line jack is not a mod-

ular jack, you can update the wir-

ing yourself, using jacks and

adapters available at your local

RadioShack store. Or, you can let

the phone company update the

wiring for you.

• The USOC number of the jack to

be installed is RJ11C (RJ11W if

you want to mount it on a wall

plate).

Placing the Base on a

Desk Top

Follow these steps when you place the

base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the TEL LINE

jack on the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

43-1088_90.fm Page 5 Tuesday, August 17, 1999 2:57 PM

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

4. Route the adapter’s cord through

the strain relief slot on the base

(as shown).

5. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

6. Lift the base’s antenna to a verti-

cal position.

Mounting the Base on a

Wall Plate

1. Plug one end of the supplied short

modular cord into the TEL LINE

jack on the back of the base.

2. Route the modular cord through

the right slot on the bottom of the

base.

Strain Relief

Slot

43-1088_90.fm Page 6 Tuesday, August 17, 1999 2:57 PM

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

4. Route the adapter’s cord through

the left side of the strain relief slot

on top of the base and through the

left slots at the bottom of the base.

5. Plug the short modular cord into

the wall plate jack, press the

excess cord into the slot in the

center of the base, then align the

base’s keyhole slots with the wall

plate studs and slide the base

downward to secure it.

Strain Relief

Slot

Slot for

Excess

Cord

6. Press and lift out the handset

holder, turn it over and rotate it

180°, then snap it back into place

so it holds the handset.

7. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

8. Lift the base’s antenna to a verti-

cal position.

Mounting the Base Directly

on the Wall

For this mounting method, you need

two flat-head wood screws (not sup-

plied) with heads that fit into the key-

hole slots on the bottom of the base.

1. Drill two holes 315/16

inches apart. Then

thread a screw into

each hole, letting the

heads extend about

3/16 inch from the

wall.

3/16

315/16

43-1088_90.fm Page 7 Tuesday, August 17, 1999 2:57 PM

2. Plug one end of the supplied long

modular cord into the TEL LINE

jack on the back of the base.

3. Route the modular cord through

the right slots on the bottom of the

base.

4. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

5. Route the adapter’s cord through

the left side of the strain relief slot

on top of the base and through the

left slots on the bottom of the

base.

6. Align the keyhole slots with the

mounting screws and slide the

base downward to secure it.

7. Plug the modular cord into a mod-

ular phone line jack.

Strain Relief

Slot

43-1088_90.fm Page 8 Tuesday, August 17, 1999 2:57 PM

8. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the

handset.

9. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

10. Lift the base’s antenna to a verti-

cal position.

CONNECTING AND

CHARGING THE

BATTERY PACK

The phone comes with a rechargeable

nickel-cadmium battery pack in the

handset. Before using your phone, you

must connect the battery pack and

then charge it for about 14 hours.

1. Remove the screw on the battery

compartment cover, then press

down and slide the cover in the

direction of the arrow to remove it.

2. Plug the battery pack’s plastic

connector into the socket in the

compartment. The connector fits

only one way.

Note: For easier battery pack con-

nection, lift it out of the compart-

ment, insert its connector into the

socket and replace the battery

pack inside the compartment.

3. Replace the cover, then reinsert

and tighten the screw.

To charge the battery pack, simply

place the handset on the base. The

CHARGE indicator on the base lights.

Recharge the battery pack when the

handset beeps and the TALK/BATT

LOW indicator flashes.

CHARGE Indicator

43-1088_90.fm Page 9 Tuesday, August 17, 1999 2:57 PM

Notes:

• If the CHARGE indicator does not

light when you place the handset

on the base, be sure the battery

pack and AC adapter are correctly

and securely connected.

Also, check the charging contacts

on the handset and the base. If

the contacts are dirty or tarnished,

clean them with a pencil eraser.

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work

and you might hear an error tone.

If this happens, return the handset

to the base for a few seconds.

• About once a month, fully dis-

charge the battery pack by keep-

ing the handset off the base until

the TALK/BATT LOW indicator

flashes. Otherwise, the battery

pack loses its ability to fully re-

charge.

• If the TALK/BATT LOW indicator

does not light and the phone does

not work, recharge the battery

pack. (The battery power might be

too low to light the indicator.)

• If the battery pack becomes weak

during a call, you hear a beep ev-

ery 30 seconds and the TALK/

BATT LOW indicator flashes ev-

ery 3 seconds. Recharge the bat-

tery pack.

• If the battery pack is completely

discharged, the handset loses the

security access-protection code.

To reset the code, place the hand-

set on the base and charge the

battery pack.

• The supplied battery pack should

last for about a year. When the

battery pack loses its ability to

fully recharge, order a replace-

ment battery pack from your local

RadioShack store (see “Replacing

the Battery Pack” on Page 20).

43-1088_90.fm Page 10 Tuesday, August 17, 1999 2:57 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack ET-686 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-929 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack 43-1107 Bedienungsanleitung

Radio Shack

Radio Shack ET-537 Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 43-3595 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Call Waiting/Caller... Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack 43-3558 Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack Sprint SP-514 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack 43-3571 Bedienungsanleitung

Radio Shack

Radio Shack ET-545 Bedienungsanleitung

Radio Shack

Radio Shack ET-1109 Bedienungsanleitung

Radio Shack

Radio Shack 900MHz Hands-free Phone Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum... Bedienungsanleitung

Radio Shack

Radio Shack TAD-1016 Bedienungsanleitung

Radio Shack

Radio Shack TAD-728 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung