Radio Shack TAD-727 Bedienungsanleitung

Cat. No. 43-727

OWNER’S MANUAL

Please read before using this equipment.

TAD-727

900 MHz Digital Spread Spectrum Cordless

Telephone with Digital Answering System

43-727.fm Page 1 Monday, December 20, 1999 4:28 PM

FEATURES

Your RadioShack TAD-727 900 MHz

Digital Spread Spectrum Cordless Tele-

phone uses advanced cordless tele-

phone technology to give you superior

audio quality and extended range.

The TAD (Telephone Answering Device)

has about a 15 minute record capacity

and stores all messages on a microchip.

This gives you advanced capabilities

over tape-based answering machines.

For example, you can delete individual

messages and save the rest. Because

your TAD is fully digital, there are no

tapes to bother with, no tape mecha-

nisms to wear out, and no lost messag-

es if power fails.

The remote operation feature lets you

access your TAD from a touch-tone

phone, and guides you through system

operation with voice prompts.

Telephone Features

900 MHz Operation — provides longer

range and less interference than many

other cordless phones.

Spread Spectrum Technology —

spreads the signal across several fre-

quencies, providing additional security

for your phone conversations.

10-Number Memory Dialing — lets you

store up to 10 numbers in memory for

quick and easy dialing.

20 Channels — automatically selects a

clear channel when you make or answer

a call, even while talking.

Two-Way Intercom/Paging System —

lets you send a signal from the base to

the handset, or from the handset to the

base, so you can page someone or eas-

ily locate the handset when it is away

from the base. If someone answers, you

can use the TAD-727 as a two-way in-

tercom.

Facedown or Faceup Handset Charg-

ing — you can place the handset on the

base facedown or faceup.

Ample Talk and Standby Time — the

supplied battery (when fully charged)

provides about 4 hours of talk time or 7

days of standby time.

Security Access-Protection Code —

automatically prevents other cordless

phone users from using your phone line

while the handset is off the base.

Redial — lets you quickly redial the last

number dialed.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Out of Range Signal — lets you know

when you move out of the base's operat-

ing range.

RadioShack is a registered trademark used by Tandy Corporation.

43-727.fm Page 2 Monday, December 20, 1999 4:28 PM

Tone/Pulse Dialing — lets you use ei-

ther type of service, and you can easily

switch from pulse to tone dialing for

long-distance, bank-by-phone, or other

special services.

Hearing-Aid Compatibility — lets you

use your phone with hearing aids that

have a T (telephone) switch.

Volume Control — lets you adjust the

volume you hear through the handset in

four steps.

Adjustable Ringer Volume — lets you

choose high or low volume for the hand-

set ringer.

Headset Jack — lets you connect an

optional headset for hands-free conve-

nience.

TAD Features

Date/Time Stamp — records the day

and time of each message.

Digitally-Synthesized Voice — guides

you through operation of the system.

Prerecorded Messages — gives you

the option of using existing outgoing

messages or recording your own.

Memo Recording — lets you leave

messages for yourself or others in your

home or office.

Answer Only — lets you play an an-

nouncement for callers to hear, without

recording their messages.

Digital Message Counter — shows the

number of messages and the operating

status of the TAD.

Remote Operation — lets you use a

touch-tone phone (or rotary phone and

pocket tone dialer) to operate the TAD

while you are away from your home or

office.

Programmable PIN — you can set a

two-digit personal identification number

(PIN) for secure remote operation.

Remote Answer-On — lets you call the

TAD from a remote location even when

it is not set to answer calls.

Toll-Saver — lets you avoid unneces-

sary long-distance charges when you

call by long distance to check your mes-

sages.

Phone Pick-Up Detection — stops re-

cording when you pick up any phone on

the same line as the TAD, and resets to

answer the next call.

Call Screening — lets you listen as a

caller leaves a message so you can de-

cide whether or not to answer the call.

Two-Way Conversation Recording —

lets you record the conversation when

you are talking on the TAD-727.

Adjustable Ring Number — lets you

set the TAD to answer after two or five

rings.

Volume Control — lets you adjust the

volume of incoming message playback.

43-727.fm Page 3 Monday, December 20, 1999 4:28 PM

This TAD has been tested and found to

comply with all applicable FCC stan-

dards and is UL listed.

We recommend you record your

phone's serial number here. The num-

ber is on the bottom of the case.

Serial Number ____________________

Important:

• Cordless phones such as this one

require AC power to operate. When

the AC power is off, you cannot dial

out or receive incoming calls using

your TAD-727. To be safe, you

should also have a phone that does

not need AC power to operate (not a

cordless phone) so you can still

make and receive calls if there is an

AC power failure.

• When AC power to the base is lost,

PF appears on the display to show

that a power failure occurred. The

TAD-727 loses the security access-

protection code connection between

the base and the handset. When

power is restored, put the handset

on the base briefly to restore this

connection so you can use the

handset.

WARNING: To reduce the risk of fire or

shock hazard, do not expose this product to rain

or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that might

be of sufficient magnitude to con-

stitute a risk of electric shock. Do

not open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

43-727.fm Page 4 Monday, December 20, 1999 4:28 PM

READ THIS BEFORE

INSTALLATION

We have designed your phone to con-

form to federal regulations and you can

connect it to most phone lines. However,

each device that you connect to the tele-

phone line draws power from the line.

We refer to this power draw as the

phone's ringer equivalence number, or

REN. The REN is on the bottom of your

phone.

If you use more than one phone or other

device on the line, add up all the RENs.

If the total is more than five, your phones

might not ring. In rural areas, a total

REN of three might impair ringer opera-

tion. If ringer operation is impaired, re-

move one of the devices from the line.

FCC STATEMENT

Your telephone complies with Part 68 of

FCC Rules. You must, upon request,

provide the FCC registration number

and the REN to your phone company.

These numbers are on the bottom of the

base.

You must not connect your phone to any

of the following:

• coin-operated systems

• party-line systems

• most electronic key phone systems

This equipment complies with the limits

for a Class B digital device as specified

in Part 15 of

FCC Rules

. These limits

provide reasonable protection against

radio and TV interference in a residential

area. However, your equipment might

cause TV or radio interference even

when it is operating properly.

To eliminate interference, you can try

one or more of the following corrective

measures.

• Reorient or relocate the receiving

antenna.

• Increase the distance between the

equipment and the radio or TV.

• Use outlets on different electrical cir-

cuits for the equipment and the

radio or TV.

Consult your local RadioShack store if

the problem still exists.

43-727.fm Page 5 Monday, December 20, 1999 4:28 PM

IMPORTANT SAFETY

INSTRUCTIONS

When using your telephone equipment,

basic safety precautions should always

be followed to reduce the risk of fire,

electric shock and injury to persons, in-

cluding the following:

1. Read and understand all instruc-

tions.

2. Follow all warnings and instructions

marked on the product.

3. Unplug this product from the wall

outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

4. Do not use this product near water,

for example, near a bath tub, wash

bowl, kitchen sink, or laundry tub, in

a wet basement, or near a swim-

ming pool.

5. Do not place this product on an

unstable cart, stand, or table. The

product may fall, causing serious

damage to the product.

6. Slots and openings in the cabinet

and the back or bottom are provided

for ventilation, to protect it from

overheating. These openings must

not be blocked or covered. The

openings should never be blocked

by placing the product on the bed,

sofa, rug, or other similar surface.

This product should not be placed in

a built-in installation unless proper

ventilation is provided.

7. This product should be operated

only from the type of power source

indicated on the marking label. If

you are not sure of the type of

power supply to your home, consult

your dealer or local power company.

8. Do not allow anything to rest on the

power cord. Do not locate this prod-

uct where the cord will be abused by

persons walking on it.

9. Do not overload wall outlets and

extension cords as this can result in

the risk of fire or electric shock.

10. Never push objects of any kind into

this product through cabinet slots as

they may touch dangerous voltage

points or short out parts that could

result in a risk of fire or electric

shock. Never spill liquid of any kind

on the product.

11. To reduce the risk of electric shock,

do not disassemble this product, but

take it to a qualified serviceman

when some service or repair work is

required. Opening or removing cov-

ers may expose you to dangerous

voltages or other risks. Incorrect

reassembly can cause electric

shock when the appliance is subse-

quently used.

12. Unplug this product from the wall

outlet and refer servicing to qualified

service personnel under the follow-

ing conditions:

• When the power supply cord or

plug is damaged or frayed.

• If liquid has been spilled into the

product.

• If the product has been exposed

to rain or water.

43-727.fm Page 6 Monday, December 20, 1999 4:28 PM

• If the product does not operate

normally by following the operat-

ing instructions. Adjust only those

controls, that are covered by the

operating instructions because

improper adjustment of other con-

trols may result in damage and

will often require extensive work

by a qualified technician to

restore the product to normal

operation.

• If the product has been dropped

or the cabinet has been dam-

aged.

• If the product exhibits a distinct

change in performance.

13. Avoid using a telephone (other than

a cordless type) during an electrical

storm. There may be remote risk of

electric shock from lightning.

14. Do not use the telephone to report a

gas leak in the vicinity of the leak.

Installation:

1. Never install telephone wiring during

a lightning storm.

2. Never install telephone jacks in wet

locations unless the jack is specifi-

cally designed for wet locations.

3. Never touch uninsulated telephone

wires or terminals unless the tele-

phone line has been disconnected

at the network interface.

4. Use caution when installing or modi-

fying telephone lines.

CAUTION: TO REDUCE THE RISK OF

FIRE OR INJURY TO PERSONS,

READ AND FOLLOW THESE IN-

STRUCTIONS.

1. Use only the required size and type

battery.

2. Do not dispose of the battery in a

fire.

The cell may explode. Check with

local codes for possible special dis-

posal instructions.

3. Do not open or mutilate the battery.

Released electrolyte is corrosive

and may cause damage to the eyes

or skin. It may be toxic if swallowed.

4. Exercise care in handling batteries

in order not to short the battery with

conducting materials such as rings,

bracelets, and keys. The battery or

conductor may overheat and cause

burns.

5. Charge the battery provided with or

identified for use with this product

only in accordance with the instruc-

tions and limitations specified in this

manual.

6. Observe proper polarity orienta-

tions between the battery and bat-

tery charger.

7. Use only the required size and type

AC adapter.

SAVE THESE INSTRUCTIONS

43-727.fm Page 7 Monday, December 20, 1999 4:28 PM

CONTENTS

Installation ............................................................................................................. 10

Mounting the Phone ......................................................................................... 10

On a Desk .................................................................................................. 10

On a Wall Plate or Wall .............................................................................. 11

Connecting and Charging the Battery Pack ..................................................... 12

Setting the Dialing Mode .................................................................................. 14

Setting the Ringers ........................................................................................... 14

Turning the Ringers On or Off .................................................................... 14

Setting the Handset's Ringer Volume ........................................................ 15

Telephone Operation ............................................................................................ 16

Making and Receiving Calls ............................................................................. 16

Out of Range Signal ......................................................................................... 16

Adjusting the Handset Volume ......................................................................... 16

Using Redial ..................................................................................................... 16

Using Flash ....................................................................................................... 17

Using Tone Services On a Pulse Line .............................................................. 17

Using the Intercom ........................................................................................... 17

Paging from the Base to the Handset ........................................................ 18

Paging from the Handset to the Base ........................................................ 18

Memory Dialing ................................................................................................. 18

Storing a Number ....................................................................................... 18

Entering a Pause ....................................................................................... 19

Dialing a Memory Number ......................................................................... 19

Chain-Dialing Service Numbers ................................................................. 19

Testing Stored Emergency Numbers ......................................................... 20

Using a Headset ............................................................................................... 20

TAD Operation ....................................................................................................... 21

Using the Handset to Control the TAD ............................................................. 21

Setting the Number of Rings ............................................................................ 21

Setting the Day and Time ................................................................................. 22

Selecting an Outgoing Message ....................................................................... 23

Recording an Outgoing Message ..................................................................... 23

Setting the TAD to Answer Calls ...................................................................... 24

Screening Calls ................................................................................................ 25

Recording a Memo ........................................................................................... 25

Recording Telephone Conversations ................................................................ 25

Using the Handset ..................................................................................... 26

Using the Base ........................................................................................... 26

43-727.fm Page 8 Monday, December 20, 1999 4:28 PM

Playing Messages ............................................................................................ 26

Deleting Messages ........................................................................................... 27

Adjusting the TAD's Volume ............................................................................. 27

Remote Operation ................................................................................................. 28

Using the Toll-Saver ......................................................................................... 28

Setting the Remote Operation Pin .................................................................... 28

Accessing the TAD Remotely .................................................................... 28

Troubleshooting .................................................................................................... 30

Care and Maintenance .......................................................................................... 32

Replacing the Battery Pack .............................................................................. 33

The FCC Wants You To Know .......................................................................... 34

Lightning ........................................................................................................... 34

43-727.fm Page 9 Monday, December 20, 1999 4:28 PM

INSTALLATION

MOUNTING THE PHONE

You can place the TAD-727's base on a

desk or table, mount it on a standard

wall plate, or mount it directly on a wall.

Choose a location that is:

• near an AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls or

filing cabinets, wireless intercoms,

alarms, and room monitors

• away from other cordless phones

The base's location affects the hand-

set's range. If you have a choice of sev-

eral locations, try each to see which

provides the best performance.

Caution: You must use a Class

2 power source that supplies 9

volts DC and delivers at least

500 mA. Its center tip must be set to

negative and its plug must fit the TAD-

727's DC 9V AC ADAPTER jack. The sup-

plied RadioShack adapter was specifi-

cally designed for your TAD-727. Use

only the supplied adapter. Using an

adapter that does not meet these speci-

fications could damage the TAD-727 or

the adapter.

Notes:

• Your telephone connects directly to

a modular phone line jack. If your

phone line jack is not a modular

jack, you can update the wiring

yourself, using jacks and adapters

available from your local

RadioShack store. Or, you can let

the telephone company update the

wiring for you.

• The USOC number of the jack to be

installed is RJ11C, or RJ11W for a

wall plate jack.

On a Desk

Follow these steps when you place the

base on a desk or table.

1. Plug one end of the supplied long

modular cord into the TEL LINE jack

on the back of the base.

2. Plug the modular cord's other end

into a modular phone line jack.

3. Insert the supplied AC adapter's

barrel plug into the DC 9V AC

ADAPTER jack on the back of the

base.

43-727.fm Page 10 Monday, December 20, 1999 4:28 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-548 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack 43-3533 Bedienungsanleitung

Radio Shack

Radio Shack 43-329 Bedienungsanleitung

Radio Shack

Radio Shack 43-5862 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1017 Bedienungsanleitung

Radio Shack

Radio Shack 43-3570 Bedienungsanleitung

Radio Shack

Radio Shack ET-1110 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack 2-Line 900 MHz Handsfree Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3537 Bedienungsanleitung

Radio Shack

Radio Shack ET-550 Bedienungsanleitung

Radio Shack

Radio Shack 43-3887 Bedienungsanleitung

Radio Shack

Radio Shack 43-3817 Bedienungsanleitung

Radio Shack

Radio Shack ET-905 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack ET-1126 Bedienungsanleitung

Radio Shack

Radio Shack 5.8 GHz Multi-Handset Expandable Cordless Telephone with Digital... Bedienungsanleitung

Radio Shack

Radio Shack 43-3549 Bedienungsanleitung

Radio Shack

Radio Shack ET-1123 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack TAD-734 Bedienungsanleitung

Radio Shack

Radio Shack 43-1088 Bedienungsanleitung

Radio Shack

Radio Shack 43-3577 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung