Regulus 16942 Bedienungsanleitung

www.regulus.eu

1ph heating element w. conn.&switch

Installation and Operation Manual

SINGLE-PHASE HEATING ELEMENT

with connector and switch

│2

REGULUS - Single-phase heating element - www.regulus.eu

1 General .................................................................................................................................................. 3

1.1 Application ............................................................................................................................ 3

1.2 Installation .............................................................................................................................. 3

1.3 Maintenance .......................................................................................................................... 3

1.4 Disposal ................................................................................................................................. 3

2 Single-phase heating element with connector and switch ..................................................................... 3

2.1 Technical description ............................................................................................................ 3

2.2 Dimensions ........................................................................................................................... 3

2.3 Connection to power supply .................................................................................................. 4

2.4 Wiring diagram ....................................................................................................................... 4

2.4.1 Wiring diagram of the heating element .................................................................. 4

2.5 Commissioning, operation and possible faults ...................................................................... 4

2.5.1 DHW heating in a hot water storage tank ............................................................. 5

2.5.2 Heating fluid heating in a thermal store ................................................................. 5

2.5.3 Heating element state during operation ................................................................. 5

2.5.4 Possible faults ........................................................................................................ 5

3 │

REGULUS - Single-phase heating element - www.regulus.eu

1 - General

1.1 - Application

This electric heating element is designed to heat sanitary water in a hot water storage tank or heating fluid in a

thermal store, incl. DUO Thermal Stores. This heating element is not designed to heat fluids in stainless steel

vessels.

1.2 - Installation

Screw the el. heating element into the respective threaded sleeve (G 6/4” F) with the cable gland pointing

downwards. Sealing cord, hemp, Teflon tape or semi-permanent thread sealant should be used to avoid leaks.

1.3 - Maintenance

Clean the exterior of the heating element with a soft cloth and a suitable detergent. Never use abrasive clean-

ers or solvents.

If the element is used in extra hard water, it is recommended to remove sediments at least once a year.

Unplug the element before cleaning. Then drain water from the tank and dismount the heating element.

Scratch the hard deposits on the heating rod with a plastic or wooden spatula and flush with water. Be careful

not to damage the protective nickel layer on the heating rod. Then reinstall the element according to this in-

struction manual, fill the tank with water, air-bleed and pressurize it. Check the threaded connection for leaks.

Finally, reconnect the heating element to the mains.

1.4 - Disposal

IMPORTANT INFORMATION ON PROPER DISPOSAL OF E-WASTE AS REQUIRED BY THE

EC DIRECTIVE 2002/96/EC (WEEE)

Do not dispose of this product as unsorted municipal waste. Please dispose of this

product by returning it to the point of sale or to your local municipal collection point for

recycling.

Respecting these rules will help to preserve, protect and improve the quality of

the environment, protect human health and utilize natural resources prudently and

rationally. The crossed out wheeled bin with marking bar, printed ether in the Manual

or on the product itself, identifies that the product must be disposed of at a

recycling collection site. WEEE Registration Number: 02771/07-ECZ

2 - Single-phase heating element with

connector and switch

2.1 - Technical description

The electric heating element consists of a nickel-plated heating rod with G 6/4“ outer thread, a safety capillary

thermostat with manual reset in case of a temperature drop below 40 °C, set to 99 °C and +0 °C, -10 °C toler-

ance, 3× 1.5 mm² power supply cable with a connector. The power supply cable is 5 m long. IP 40 protection.

2.2 - Dimensions

230 V

output power supply model code material

non-heat-

ing

end LN

heating rod

length L

min. hot wa-

ter storage

tank size

min. thermal store size

[kW] [mm] [mm]

2.0 1/N/PE AC 230V ETT-N-2,0 16942 nickel-plated copper 180 350 RGC 120 H PS 200 HSK 390 DUO 390

3.0 1/N/PE AC 230V ETT-N-3,0 16943 nickel-plated copper 180 450 RBC 200 PS 200 HSK 390 DUO 390

│4

REGULUS - Single-phase heating element - www.regulus.eu

2.3 - Connection to power supply

The electric heating element connects to a solar controller connector 1/N/PE AC 230V 50Hz by a flexible

power cord. Do not use the element if the power supply cord or connector is damaged. All repairs shall be

performed by a specialized company.

2.4 - Wiring diagram

2.4.1 - Wiring diagram of the heating element

2.5 - Commissioning, operation and possible faults

WARNING!

THE OUTGOING HOT WATER SHALL NOT BE LEAD THROUGH COMMON PLASTIC PIPES. THE PIPING

USED SHALL BE RESISTANT TO TEMPERATUREs OF 100 °C AT LEAST.

IF PLAIN COMMON PLASTIC PIPING IS USED, ITS SERVICE LIFE IS SIGNIFICANTLY REDUCED UN-

DER TEMPERATURES OVER 60 °C. WHEN COMBINED WITH IMPROPER PIPE FIXING THAT PRE-

VENTS/RESTRICTS ITS DILATATION, THE PIPE SERVICE LIFE MIGHT BE JUST SEVERAL HOURS!

IN ORDER TO TIGHTEN THE HEATING ELEMENT, NEVER GRASP ON THE PLASTIC BOX BUT USE

THE HEXAGON INSTEAD.

Water in direct contact with the heating element shall not exceed the values given in the chart below. The

manufacturer bears no responsibility for defects (e.g. limescale deposits on the heating element) caused by

unsuitable operation conditions.

Table of limit values for total dissolved solids in hot water

Description pH Total dissolved solids (TDS) Ca Chlorides Mg Na Fe

Max. value 6.5-9.5 600 mg/l 40 mg/l 100 mg/l 20 mg/l 200 mg/l 0.2 mg/l

5 │

REGULUS - Single-phase heating element - www.regulus.eu

2.5.2 - Heating fluid heating in a thermal store

Fill the heating system with heat transfer fluid, airbleed it and pressurize to the working pressure. Set the de-

sired temperature via the solar controller.

2.5.3 - Heating element state during operation

When the safety temperature is reached, the safety thermostat will cut off the heating element from power

supply. The safety thermostat features no automatic reset. After the tank cools down to below 40 °C, unscrew

the lid of the heating element and reset it by pressing the button. The heating element is ready again.

2.5.4 - Possible faults

If the tank gets overheated without any other heat source used (the solar controller probably does not turn off

the heating element when the set temperature is reached), call your service provider.

If the heating element shows signs of another defect, disconnect it from the mains immediately and call your

service provider.

2.5.1 - DHW heating in a hot water storage tank

In order to heat water in the hot water storage tank, open the cold water inlet, fill the tank with water and air-

bleed it by opening the hot water tap. Set the desired temperature via the solar controller.

It is recommended to set the temperature to 60 °C. This temperature guarantees the best operation of the

heating element, offering also:

- protection against Legionella

- cost reduction

- slower deposit formation

REGULUS spol. s r.o.

E-mail: sales@regulus.eu

Web: www.regulus.eu

v1.0-06/2018

SINGLE-PHASE HEATING ELEMENT

with connector and switch

WARRANTY CERTIFICATE

Model: .......................................................................................

Serial number: .......................................................................

Seller: .......................................................... Date of purchase: ...............................

1. The warranty period is 24 months from the date of purchase

2. The product shall be installed and commissioned by a competent company or a person

trained by the Manufacturer.

3. When claiming warranty, this Warranty Certificate must be submitted together with the

purchase receipt.

4. The warranty is valid only when the technical conditions set by the Manufacturer,

installation manual and instructions in the documentation and on the product itself are

respected.

5. The warranty does not cover defects caused by external conditions or improper working

conditions, defects caused by normal wear and tear, further when the product is not used

in compliance with its purpose and when the defect was caused by mechanical damage

to the product, improper handling, tampering by a third person, improper installation,

improper stocking, natural disaster etc.

COMMISSIONING

Company: …………………....................……………..

Date: ……………….................................……..

Rubber stamp print and signature of the technician:

WARRANTY CONDITIONS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regulus Boiler Handbücher

Regulus

Regulus RDC 200Z Bedienungsanleitung

Regulus

Regulus THERMAL STORE HSK 400 P+ Bedienungsanleitung

Regulus

Regulus RegulusHBOX 212 CTC 3/3 Bedienungsanleitung

Regulus

Regulus R0BC 200 Bedienungsanleitung

Regulus

Regulus PS2F N+ Series Bedienungsanleitung

Regulus

Regulus NBC 170 HP Bedienungsanleitung

Regulus

Regulus PS 400 K+ Bedienungsanleitung

Regulus

Regulus LYRA 1000 DVS Betriebsanleitung

Regulus

Regulus THERMAL STORE HSK 400 PR+ Betriebsanleitung

Regulus

Regulus R2DC 200 Bedienungsanleitung

Regulus

Regulus PS 100 IZ Bedienungsanleitung

Regulus

Regulus PSWF 500 N+ Bedienungsanleitung

Regulus

Regulus R2BC 200 Bedienungsanleitung

Regulus

Regulus RBC 300 HP Bedienungsanleitung

Regulus

Regulus RDC 160 Bedienungsanleitung

Regulus

Regulus R2DC 160 Bedienungsanleitung

Regulus

Regulus RBC 300 Bedienungsanleitung

Regulus

Regulus RBC 200HP Bedienungsanleitung

Regulus

Regulus RegulusBOX Bedienungsanleitung

Regulus

Regulus R2BC 200 Bedienungsanleitung

Regulus

Regulus RGC 120H Bedienungsanleitung

Regulus

Regulus HSK 500 Bedienungsanleitung

Regulus

Regulus R2GC 250 Bedienungsanleitung

Regulus

Regulus R0BC Series Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung