Reliable F1-56-300 Series Bedienungsanleitung

Model F1-56-300 Pendent

Model F1-56-300 Upright

F1-56-300 Series Sprinklers Summary

Sprinkler

Model

K-Factor gpm/psi1/2

(lpm/bar1/2)Orientation Listings & Approvals Max. Working Pressure

psi (bar)

Sprinkler

Identication

Number (SIN)

F1-56-300 5.6 (80)

Upright

cULus 300 (20.7)

RA2525

Pendent RA2514

Table A

Note: Not all versions of the product are shown.

Features

• Standard coverage standard-response sprinklers

• 300 psi (20.7 bar) rated

• Upright and pendent deflectors

• Low prole, compact design

• Available in a wide variety of nishes

Product Description

Reliable Model F1-56-300 series sprinklers are 300 psi (20.7 bar)

rated, standard-response standard spray automatic re sprinklers

utilizing a 5.0 mm glass bulb thermal element.

Pendent sprinklers may be installed exposed or surface mounted

using escutcheons such as the Reliable Models B, C, or HB

(reference Technical Bulletin 204). When installed recessed, the

Model F1-56-300 series sprinklers are specically listed with and

may only be installed with Reliable listed recessed escutcheons.

Refer to the technical information on the following pages for

specic listings for recessed and concealed installations and refer

to Figure 3 for dimensional information.

When tted with an approved water shield, these sprinklers may

considered intermediate sprinklers for use in racks, below grated

walkways, and other areas where intermediate level sprinklers are

required.

Table A provides a summary of the approvals and availability

of specic Model F1 series sprinkler congurations. Additional

technical information for each sprinkler model is provided on the

following pages.

Note: This bulletin may contain information on New and Legacy

sprinklers that reflects a dimensional change only.

Sprinkler Identication Number (SIN), application, performance,

and listings/approval are not otherwise affected. Sprinklers with

New frames will include the sufx “N” in the order.

www.reliablesprinkler.com

K-factor 5.6 (80)

F1-56-300 Series

Standard Response Sprinklers

Bulletin 075 October 2022

Model F1-56-300 Upright Sprinkler SIN RA2525

Technical Specications

Style: Upright

Threads: 1/2” NPT or ISO 7-R1/2

Nominal K-Factor: 5.6 (80 metric)

Max. Working Pressure: 300 psi (20.7 bar)

Material Specications

Thermal Sensor: 5 mm Glass Bulb

Sprinkler Frame: Brass Alloy

Cap: Bronze Alloy

Sealing Washer: Nickel with PTFE

Load Screw: Copper Alloy

Deflector: Brass Alloy

Sprinkler Finishes

(See Table B)

Sensitivity

Standard response

Temperature Ratings

135°F (57°C)

155°F (68°C)

175°F (79°C)

200°F (93°C)

286°F (141°C)

360°F (182°C)

Guards & Shields (New Frame)

F-1 Guard

F-3 Guard with Shield

Guards and Shields (Legacy Frame)

C-3 Guard with Shield

D-1 Guard

D-3 Guard with Shield

Sprinkler Wrench

Model W2

Model J (New frame with guard installed)

Model JD (Legacy frame with guard installed)

Listings and Approvals

cULus Listed

Model F1-56-300 Upright Sprinkler Components and Dimensions Figure 1

Deflector

Glass Bulb

(3 mm)

Wrench Flat

Threads

1 3/8" [33mm]

Cap/Seal Assembly

Load Screw

2 3/8" [60mm]

F1_HALF_UPR

Bulletin 075

October 2022

Page 2 of 6

www.reliablesprinkler.com

Model F1-56-300 Pendent Sprinkler SIN RA2514

Technical Specications

Style:

Pendent

Recessed Pendent

Threads: 1/2” NPT or ISO 7-R1/2

Nominal K-Factor: 5.6 (80 metric)

Max. Working Pressure: 300 psi (20.7 bar)

Material Specications

Thermal Sensor: 5 mm Glass Bulb

Sprinkler Frame: Brass Alloy

Cap: Bronze Alloy

Sealing Washer: Nickel with PTFE

Load Screw: Copper Alloy

Deflector: Brass Alloy

Sprinkler Finishes

(See Table B)

Sensitivity

Standard response

Temperature Ratings (1)

135°F (57°C)

155°F (68°C)

175°F (79°C)

200°F (93°C)

286°F (141°C)

360°F (182°C)

Recessed Escutcheons

Model F1

Model F2

Model FP

Guards & Shields (New Frame)(2)

F-7 Guard

F-8 Guard/Shield Kit

S-1 Shield

Guards and Shields (Legacy Frame)

D-1 Guard

D-5 Guard with Shield

S-1 Shield

Sprinkler Wrenches

Model W2 (non-recessed)

Model W4 (recessed or concealed)

Model J (New frame with guard installed)

Model JD (Legacy frame with guard installed)

Listings and Approvals

cULus Listed

Notes:

1. 286°F (141°C) and higher temperature rated sprinkler not listed for recessed use.

2. Not suitable for recessed pendent installation.

Model F1-56-300 Pendent Sprinkler Components and Dimensions Figure 2

F1FR_HALF_PEND_INT

Deflector

Glass Bulb

(3 mm)

Wrench Flat

Threads

3 1/4" [83mm]

2 1/4" [57mm]

1" [25mm]

Load Screw

Cap/Seal

Assembly

Shown with Optional S-1 Water

Shield (Ordered Separately)

Note: Please refer to Figure 3 for recessed installation.

Bulletin 075

October 2022

Page 3 of 6

www.reliablesprinkler.com

Models F1 & F1FR Pendent Sprinkler

with Model F1 Recessed Escutcheon

3/4" (19mm) Nominal Adjustment

2-7/8" (72 mm) Dia.

1-3/4"

(44 mm)

2-1/4"

(57 mm) Dia.

Hole in Ceiling

1-15/16"

(49 mm) Dia.

Minimum

Recess

Maximum

Recess

(25 mm)

Face of Fitting

to Face of Ceiling

1-1/8" (29 mm) at

Max. Recess

3/8" (10 mm) at

Min. Recess

Models F1 & F1FR Pendent Sprinkler

with Model FP Recessed Escutcheon

1/2" (13mm) Nominal Adjustment

(25 mm)

2-5/16"

(59 mm) Dia.

Minimum

Recess Maximum

Recess

1/2"

(12 mm)

3-3/16" (78 mm) Dia.

Face of Fitting

to Face of Ceiling

1-1/2" (38 mm) at

Max. Recess

1" (25 mm) at

Min. Recess

2-7/8" (72 mm) Dia.

1-3/4"

(44 mm)

Minimum

Recess

Maximum

Recess

1-1/4"

(32 mm)

Face of Fitting

to Face of Ceiling

7/8" (22 mm) at

Max. Recess

3/8" (10 mm) at

Min. Recess

2-1/4"

(57 mm) Dia.

Hole in Ceiling

1-15/16"

(49 mm) Dia.

2-1/2"

(64 mm) Dia.

Hole in Ceiling

Models F1 & F1FR Pendent Sprinkler

with Model F2 Recessed Escutcheon

1/2" (13mm) Nominal Adjustment

F1_REC_PEND

Reducing

Fitting

Reducing

Fitting

Reducing

Fitting

Note: Model FP recessed assemblies may not be used where the

pressure in the space above the ceiling is positive with respect to

the protected area. Ensure that the openings in the Model FP cup

are unobstructed following installation.

Vented Cup

Recessed Installation: Pendent Sprinklers Figure 3

FP Recessed Escutcheon

F1 Recessed Escutcheon

(F2 Similar)

Bulletin 075

October 2022

Page 4 of 6

www.reliablesprinkler.com

Installation

Model F1 Series sprinklers must be installed in accordance

with NFPA13 and the requirements of all applicable authorities

having jurisdiction. Model F1-56-300 Series sprinklers must be

installed with the Reliable sprinkler installation wrench identied

in this Bulletin. Any other wrench may damage the sprinkler. The

Models W2 and W4 wrenches have two sets of jaws. Use the

smallest set of jaws that t on the wrench flats of the sprinkler.

A leak tight sprinkler joint can be obtained with a torque of 6

to 18 lb-ft (11 to 24 N.m). Do not tighten sprinklers over the

maximum recommended installation torque. Exceeding the

maximum recommended installation torque may cause leakage or

impairment of the sprinkler.

Glass bulb sprinklers have orange bulb protectors or protective

caps to minimize bulb damage during shipping, handling and

installation. Reliable sprinkler installation wrenches are designed

to install sprinklers with bulb protectors in place. Remove the bulb

protector at the time when the sprinkler system is placed in service

for re protection. Removal of the bulb protector before this time

may leave the bulb vulnerable to damage. Remove bulb protectors

by undoing the clasp by hand. Do not use tools to remove bulb

protectors.

Standard Finishes Special Application Finishes

Sprinkler F1, F2 and FP(2)

Escutcheons Sprinkler F1, F2 and FP(2)

Escutcheons

Bronze Brass Electroless Nickel PTFE(3) Bright Brass

Chrome Chrome Bright Brass(4) Satin Chrome

White Polyester(3) White Polyester Satin Chrome Custom Color Polyester

Custom Color Polyester(3)

Lead(3)

Wax(3)(6)

Wax over Lead(3)(6)

Notes:

1. Paint or any other coating applied over the factory nish will void all approvals and warranties.

2. Model FP escutcheons utilize a galvanized steel cup with a nished trim ring.

3. cULus Listed as corrosion resistant.

4. For 200°F (93°C) maximum temperature rated sprinklers only.

5. Clear wax used on ordinary temperature rated sprinklers; brown wax used on intermediate temperature rated sprinklers. Brown wax may be used on

high temperature rated sprinklers where the ambient temperature does not exceed 150°F (66°C).

Finishes(1) Table B

Wrenches

Model W2 (upright, pendent) Model W4

(recessed, concealed pendent)

Model J (with guard installed)

Maintenance

Reliable Model F1-56-300 series sprinklers should be inspected

and the sprinkler system maintained in accordance with NFPA

25, as well as the requirements of any Authorities Having

Jurisdiction.

Prior to installation, sprinklers should remain in the original

cartons and packaging until used. This will minimize the potential

for damage to sprinklers that could cause improper operation or

non-operation.

Do not clean sprinklers with soap and water, ammonia liquid or

any other cleaning fluids. Remove dust by gentle vacuuming

without touching the sprinkler.

Replace any sprinkler which has been painted (other than factory

applied). A stock of spare sprinklers should be maintained to

allow quick replacement of damaged or operated sprinklers.

Failure to properly maintain sprinklers may result in inadvertent

operation or non-operation during a re event.

Bulletin 075

October 2022

Page 5 of 6

www.reliablesprinkler.com

P/N 9999970624

Bulletin 075

October 2022

Page 6 of 6

www.reliablesprinkler.com

Guarantee

For the guarantee, terms, and conditions, visit www.

reliablesprinkler.com.

Ordering Information

Specify the following when ordering:

Model

• F1-56-300

Deflector/Orientation

• Upright

• Pendent

Temperature Rating

• See sprinkler technical specications

Sprinkler Finish

• See Table B

Recessed Escutcheon*

• F1

• F2

• FP

Escutcheon Finish

• See Table B

Sprinkler Wrench

• Model W2 (upright, non-recessed pendent)

• Model W4 (recessed & concealed pendent)

• Model J (with guard installed)

Note: 286°F (141°C) and higher temperature rated sprinklers are not listed to be used recessed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Reliable Bewässerungssystem Handbücher

Reliable

Reliable KFR56 Series Bedienungsanleitung

Reliable

Reliable F156 Series Bedienungsanleitung

Reliable

Reliable RFC43 LL Benutzerhandbuch

Reliable

Reliable G6-80 K8.0 Bedienungsanleitung

Reliable

Reliable SWC Handbuch

Reliable

Reliable G6-80 Handbuch

Reliable

Reliable G5-56 Dry Bedienungsanleitung

Reliable

Reliable F1 LO Bedienungsanleitung

Reliable

Reliable DDX PrePaK Wartungshandbuch

Reliable

Reliable G Series Bedienungsanleitung

Reliable

Reliable F3QR80 Series Bedienungsanleitung

Reliable

Reliable DD56-6 Handbuch

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable GXLO Series Handbuch

Reliable

Reliable Sidewall Concealer SWC Bedienungsanleitung

Reliable

Reliable F156 Series Handbuch

Reliable

Reliable G4-300 Bedienungsanleitung

Reliable

Reliable Concealer G4A Bedienungsanleitung

Reliable

Reliable F1FR56-300 Series Bedienungsanleitung

Reliable

Reliable DH80 Dry Bedienungsanleitung

Reliable

Reliable G5-56 Handbuch

Reliable

Reliable F1FR Series Handbuch

Reliable

Reliable Pantman F1 Bedienungsanleitung

Reliable

Reliable F1 Res 30 LL Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Bedienungsanleitung

Johnson Controls

Johnson Controls tyco ESFR-17 Bedienungsanleitung

Victaulic

Victaulic VicFlex I-VICFLEX.AQC-U Bedienungsanleitung