ResMed Stellar 150 Bedienungsanleitung

ResMed Stellar 150 Client Version

How to power on/off

When unit is plugged in and screen remains dark, flick the ON/Standby switch at the back of the unit next

to the power cord inlet. The screen will light up and the unit will exhale once. The screen will display the

time and date. To power off, flick switch at back of unit, the screen will prompt the user to answer Yes/No

to power off. Select your response by turning the push dial to highlight Yes or No, then press the dial to

make your choice.

How to Start/ stop

To start the blower press the start/stop button that is lit up below the push dial. The blower will be

initiated. To stop the blower press start/stop and the screen will prompt the user to confirm Yes/No to

stop blower. Select YES/NO by turning the push dial and press the push dial to make your choice.

Monitor

Setup

Info

Push

Dial

silver/

black

Start/

Stop

Battery

life %

Power

source

indicator

Alarm

signal

light

Alarm

Mute

On/Standby switch

A/C Power cord connection

To Access Parameter Menu

1. Press and hold Push Dial and Setup button together until screen

displays the heading Clinical Mode

2. Notice the highlighted box at the bottom left of the screen that

reads “5 Minutes Set Time” this indicates the time available to

access parameter settings before the unit returns to Client Mode.

(An Audible ‘beep’ will warn of the 5 minute time limit ending).

3. Press Push Dial. The screen will now display Treatment screen,

two beeps will be heard along with flashing red light visible at alarm signal.

4. Press the Setup button with the two check marks to enter Clinical Settings.

To Make Parameter Changes

1. Using the Push Dial, turn the dial to highlight the box that is labeled with the parameter you

wish to change.

2. Press the Push Dial and the blue highlight turns yellow.

3. While the box is yellow, turn the dial to change the setting.

4. Press the Push Dial again and the box returns to the blue highlight with the new setting

displayed.

5. The “Advanced settings” when chosen will display additional parameters.

6. Scroll through all settings and adjust as required.

7. To Access the Alarms Settings Page, press the double check mark button (Setup button) and

adjust as required

8. to Access the Options Page (Learn Circuit, Smart Start, etc.) press the double check mark button

(Setup Button) and adjust as required.

9. To display the main Treatment Page, press the Monitor button (lung symbol)

10. To lock the back menu, either wait 5 minutes for it to automatically lock or press and hold the

dial and the set up button at the same time. A padlock symbol will appear in the top right corner

of the screen. Unit will beep twice and visually flash red to indicate it is locked.

Exit parameter menu the last blue box on this page 3/3 will allow the user to return to the

previous screen.

Maintenance of Stellar 150 BiPAP: Replace the air filter every six months (or more often if

necessary). The air filter is not washable or reusable. Remove the air filter cover at the back of the device.

Remove and discard the old air filter. Insert a new filter. Refit the air filter cover. Wipe the exterior of the

device with a damp cloth (and mild detergent if needed).

Internal Battery In case of a power disruption (AC), the device will operate using the internal battery.

Battery life is displayed as a % in the top left corner of the display screen. The battery duration depends

on the state of charge and the device settings. Under normal conditions, the battery should last about 2

hours. The internal battery can take up to 3 hours to recharge.

Battery Maintenance: The manufacturer recommends that the internal battery be discharged and

recharged every six months. To discharge the battery: remove the power cord while the Stellar

150 is turned on (stand-by or in operation) and let the

device operate with the internal battery to a charge level of 50%. To recharge the internal battery:

plug the power cord into the AC power outlet. An orange/red light will flash next to the battery

symbol on the display screen in the “Power Source Indicator” area until the battery has recharged

to 100%

Humidification

Humidification is recommended for nasal and upper airway dryness that is a common occurrence

due to the high flow of air being directed through the nasal and oral passages.

Humidifier Maintenance: Included with the BiPAP is a yellow device that acts as a cover plate to

the water chamber when cleaning the inside of the humidifier. DAILY: Drain any residual water

from the humidifier each morning. Refill the chamber half way to the MAX water line with

DISTILLED water. MONTHLY: It is recommended that you wash your water chamber in warm

water, using a mild detergent. Remove mineral deposits in the water chamber by using a solution of

one part household vinegar to ten parts water. Rinse thoroughly with clean water and allow

chamber to air dry.

Revised April 29, 2015

Warming Base

Yellow cover

plate (opt. for

cleaning)

Opaque

“horseshoe”

plug

Water

chamber

Andere Handbücher für Stellar 150

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed S9 Series Bedienungsanleitung

ResMed

ResMed S8 Escape II Auto Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed S9 AutoSet CS-A Technisches Handbuch

ResMed

ResMed VPAP ST-A Bedienungsanleitung

ResMed

ResMed Sullivan Comfort Bedienungsanleitung

ResMed

ResMed AirFit F20 Bedienungsanleitung

ResMed

ResMed Ultra Mirage NVFFM Bedienungsanleitung

ResMed

ResMed VPAP ST Bedienungsanleitung

ResMed

ResMed Elisee 150 Gebrauchsanweisung

ResMed

ResMed S9 Escape Technisches Handbuch

ResMed

ResMed AirSense 10 Bedienungsanleitung

ResMed

ResMed AirSense 11 Bedienungsanleitung

ResMed

ResMed ResScan Bedienungsanleitung

ResMed

ResMed Mirage Kidsta Bedienungsanleitung

ResMed

ResMed AirFit F20 Bedienungsanleitung

ResMed

ResMed AirFit F30 Bedienungsanleitung

ResMed

ResMed AcuCare F1-0 Bedienungsanleitung

ResMed

ResMed AirCurve 10 ST-A Bedienungsanleitung

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed NV Elbow F20 Bedienungsanleitung

ResMed

ResMed Mirage Vista Bedienungsanleitung

ResMed

ResMed AirSense 11 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung