Ricoh Ri 100 Kurzanleitung
1
RICOH Ri 100 Notes for Wireless LAN Users
This manual explains how to connect the machine to the network via a wireless LAN interface in
the infrastructure mode.
In the infrastructure mode, communication is established via a wireless LAN access point.
DSA072
Ad hoc mode is not supported.•
Ethernet and wireless LAN settings cannot be enabled at the same time.•
Checking Your Wireless Network Environment
Before using the wireless LAN, configure the following settings and make the check.
1. Before configuring the wireless LAN settings, configure the machine’s IP address or
make DHCP enabled.
For details about configuring the machine's IP address, see "Preparing for Printing", Operat-
ing Instructions .
2. Check that the access point is operating.
CHV600
2
3. Plug the wireless LAN cable into the Ethernet port before configuring the wireless
LAN settings.
DSA343
Selecting the Configuration Method
The configuration method depends on the access point being used.
"Easy Setup" is a function for automatically configuring the wireless LAN settings. The actual
name of the function may vary depending on the access point being used. See the access point
manual.
Page 3
”Easy Setup Using the
Push Button”
Page 7
”Manual setting”
Easy Setup
“PBC Method”
Easy Setup
“PIN Method” Manual setting
Does the access point support "Easy Setup" of the wireless LAN?
Is there a push button
on the access point?
Page 5
”Easy Setup Using a
PIN Code”
YesNo
Yes No
CHV626
Manual setting:• Page 7 "Configuring Settings Using Web Image Monitor"
Manual setting:• Page 12 "Configuring Settings Using the Control Panel"
3
Easy Setup Using the Push Button
1. Turn the machine on.
DSB151
2. Press the [ /Menu] key.
3. Press the [ ] or [ /Menu] key to display the [Host Interface] menu, and then press the
[#Enter] key.
<Menu>
Host Interface
4. Press the [ ] or [ /Menu] key to display [Wireless LAN], and then press the [#Enter]
key.
<Host Interface>
Wireless LAN
5. Press the [ ] or [ /Menu] key to select [Easy Setup], and then press the [#Enter]
key.
<Wireless LAN>
Easy Setup
6. Press the WPS button on the access point.
WPS
CHV607
4
7. Press the [ ] or [ /Menu] key to select [PBC Method], and then press the [#Enter]
key.
<Easy Setup>
PBC Method
If the access point cannot be detected within 120 seconds, the search session expires.
If the connection attempt has failed, press the [#Enter] key again. If the problem persists,
check whether the access point is working properly.
Configuration is complete when connection to the access point is confirmed.
8. After you have made all the settings, press the [Escape] key.
9. Print the configuration page to check whether the machine has successfully con-
nected to the access point.
Load the print media in the cassette.
If the wireless LAN signal is reported as being unavailable (0%) on the configuration page,
the machine is not connected to the access point.
How to print the configuration page
the [ /Menu] key [List/Test Print] [Config. Page] the [#Enter] key
5
Easy Setup Using a PIN Code
1. Turn the machine on.
DSB151
2. Press the [ /Menu] key.
3. Press the [ ] or [ /Menu] key to display the [Host Interface] menu, and then press the
[#Enter] key.
<Menu>
Host Interface
4. Press the [ ] or [ /Menu] key to display [Wireless LAN], and then press the [#Enter]
key.
<Host Interface>
Wireless LAN
5. Press the [ ] or [ /Menu] key to select [Easy Setup], and then press the [#Enter]
key.
<Wireless LAN>
Easy Setup
6. Press the [ ] or [ /Menu] key to select [Display PIN], and then press the [#Enter]
key.
<Easy Setup>
Display PIN
7. Check the machine's PIN.
6
8. Enter the machine's PIN on the access point web page.
CHV609
For details, see the manual supplied with the wireless LAN access point.
9. Execute WPS (PIN system) from the access point's web page.
10. Press the [Escape] key.
11. Press the [ ] or [ /Menu] key to select [PIN Method], and then press the [#Enter]
key.
<Easy Setup>
PIN Method
If the connection attempt has failed, press the [#Enter] key again. If the problem persists,
check whether the access point is working properly.
Configuration is complete when connection to the access point is confirmed.
12. After you have made all the settings, press the [Escape] key.
13. Print the configuration page to check whether the machine has successfully con-
nected to the access point.
Load the print media in the cassette.
If the wireless LAN signal is reported as being unavailable (0%) on the configuration page,
the machine is not connected to the access point.
How to print the configuration page
the [ /Menu] key [List/Test Print] [Config. Page] the [#Enter] key
7
Manual Setting
If you cannot confirm the settings of the access point being used or the access point does not
support WPS, configure the wireless LAN settings manually.
You can configure the settings using Web Image Monitor or the control panel. This manual mainly
explains configuration using Web Image Monitor.
Configuring Settings Using Web Image Monitor
Connect the machine and computer with an Ethernet cable before configuring the settings.•
DSA345
Check the security method employed by the access point being used.•
Check the machine's IP address.•
the [ /Menu] key [Host Interface] [Network Setup] [IPv4 Address]
1. Launch the Web browser.
2. In the address bar, enter "http://(machine's IP address or host name)/".
3. Click [Administrator Login].
DSB201
A dialog box for entering the user name and password appears.
4. Enter the user name and password, and then click [OK].
If this is the first time to log in, enter "admin" as the user name and leave the password
blank.
8
5. In the menu area, click [Settings].
6. Click [Wireless LAN Settings].
7. Specify the wireless LAN settings.
If the security method is WEP
1
2
3
DSB202
1. Enter the network name of the access point.
2. Select [WEP].
3. Enter the password for the access point, and then select the [Apply] check box.
9
If the security method is WPA
1
2
DSB203
1. Enter the network name of the access point.
2. Select [WPA].
10
If the WPA authentication method is WPA-PSK or WPA2-PSK•
1
2
DSB205
1. Select [WPA-PSK] or [WPA2-PSK].
2. Enter the PSK (Pre-Shared Key), and then select the [Apply] check box.
Configure other settings if needed.
Andere Handbücher für Ri 100
10
Inhaltsverzeichnis
Andere Ricoh Multifunktionsdrucker Handbücher
Ricoh
Ricoh D093 Bedienungsanleitung
Ricoh
Ricoh Pro C5300S Bedienungsanleitung
Ricoh
Ricoh SP C260SFNw Bedienungsanleitung
Ricoh
Ricoh MP 7503SP Kurzanleitung
Ricoh
Ricoh Priport JP5000 Bedienungsanleitung
Ricoh
Ricoh H545 Bedienungsanleitung
Ricoh
Ricoh P C600 Bedienungsanleitung
Ricoh
Ricoh Aficio MP 8000 S/P Service-Handbuch
Ricoh
Ricoh G065 Bedienungsanleitung
Ricoh
Ricoh CL1000N Bedienungsanleitung
Ricoh
Ricoh C9020L Bedienungsanleitung
Ricoh
Ricoh Aficio MP 161 Gebrauchsanweisung
Ricoh
Ricoh Aficio SP C242SF Bedienungsanleitung
Ricoh
Ricoh Martini-C3.5 Bedienungsanleitung
Ricoh
Ricoh C217 Bedienungsanleitung
Ricoh
Ricoh MP 501SPF Bedienungsanleitung
Ricoh
Ricoh V-C3 D081 Kurzanleitung
Ricoh
Ricoh Aficio FX200 Handbuch
Ricoh
Ricoh Aficio MP C2050 Bedienungsanleitung
Ricoh
Ricoh SP 220SNW Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
