Rimage Everest II Montageanleitung

Align the Everest II Printer

When the Everest printer is installed, it may need to be aligned to the lift arm.

Tools Needed: T25 Torx driver

Before you begin:

 Install the Everest Printer

 Power on the Rimage DiscLab. Wait for the unit to initialize.

 Note: The Everest printer takes 2 to 3 minutes to complete the initialization.

1. Select Diagnostic 4, Jog Lift Diagnostic.

a. Press and hold the Operator Button to place the unit in diagnostics mode. The Operator

Panel indicates when to release the button.

b. When the Operator Panel displays 01 CYCLE OUTPUTS DIAGNOSTIC, press the Operator

Button four times and hold on the fourth press. This selects the JOG LIFT DIAGNOSTIC

TEST. The Lift Arm moves down toward the Print Drawer as the Print Drawer opens.

c. When the Operator Panel prompts you to place a disc, place a disc on the print pad.

2. Check the printer alignment.

a. Press the Operator Button to move the Lift Arm closer to the Print Pad.

b. Press the Operator Button again and the Lift Arm moves down and picks up the disc.

c. Manually rotate the Lead Screw counterclockwise to move the Lift Arm down to the Print Pad.

3. Check the disc alignment.

To see if the disc is centered, observe the gap

between the edge of the disc and the raised edges

as shown by the arrows.

If the disc is not centered side-to-side on the Print

Pad, continue to step 3.

If the side-to-side alignment is correct, go to step

Lift Arm

Print Pad

Disc

Lead Screw

Print Pad

Print Drawer

112063_A October 29, 2004 1

Align the Everest II Printer

3. If necessary, perform a side-to-side alignment.

a. Loosen the two torx side-to-side alignment

screws.

b. Slide the printer until the side gaps are equal.

-Important! Slide the entire printer, not the drawer.

c. Tighten the two side-to-side alignment screws.

Front to back alignment screw

Side-to-side alignment screws

4. If necessary, perform a front-to-back alignment.

a. Turn the front-to-back alignment screw until

there is a 1/16” (1.5mm) gap between the

front edge of the disc and the raised edge of

the Disc Retainer.

 Tip: You can use the T25 Torx driver, or 5/32”

Allen wrench, to turn the front-to-back alignment

screw.

b. When the printer is aligned, rotate the Lead

Screw to raise the Lift Arm up about 1.0” (2.5

cm).

5. Exit diagnostics.

a. Press and hold the Operator Button to exit

Diagnostic Test 4. The disc is lifted up to the

top output tray and released.

b. Press the Operator Button fourteen times and

hold on the last press to exit Diagnostics.

c. Press the Operator Button one more time to

close the Print Drawer.

Disc Retainer

Distance

Lift Arm

Print Pad

Lead Screw

112063_A October 29, 2004 2

Inhaltsverzeichnis

Andere Rimage Drucker Handbücher

Rimage

Rimage 480i Betriebsanleitung

Rimage

Rimage Autostar II Bedienungsanleitung

Rimage

Rimage Desktop 360i Bedienungsanleitung

Rimage

Rimage Autostar II Bedienungsanleitung

Rimage

Rimage Desktop 360i Referenzhandbuch

Rimage

Rimage Prism Bedienungsanleitung

Rimage

Rimage Prism Service-Handbuch

Rimage

Rimage 480i Bedienungs- und Sicherheitshinweise

Rimage

Rimage CDPR6 Bedienungsanleitung

Rimage

Rimage Everest Bedienungsanleitung

Rimage

Rimage Prism Bedienungsanleitung

Rimage

Rimage Autostar II Bedienungsanleitung

Rimage

Rimage 5400N Disc Copy Station Bedienungsanleitung

Rimage

Rimage EverestTM Printer Bedienungsanleitung

Rimage

Rimage Desktop 360i Gebrauchs- und Pflegehandbuch

Rimage

Rimage Amigo II Bedienungsanleitung

Rimage

Rimage AutoEverest AutoPrinter Bedienungsanleitung

Rimage

Rimage Everest III Bedienungsanleitung

Rimage

Rimage Allegro 100 Bedienungsanleitung

Rimage

Rimage Amigo II Montageanleitung

Rimage

Rimage Prism III Bedienungsanleitung

Rimage

Rimage Autostar II Bedienungs- und Sicherheitshinweise

Rimage

Rimage Amigo II Bedienungsanleitung

Rimage

Rimage Amigo II Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung