RIOTEC ICR6307AB Bedienungsanleitung

1

Programming Quick Guide

iCR6307ABU/iCR6307AB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to the

PC USB port on the PC as below described, Ensure that all connections

are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time before

use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle within

2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan the 3

barcodes on the bottom of cradle sequentially. (Shown on Fig. 3 from

1 to 3). If you are unable to complete this setting within 1 minute,

please re-plug USB cable & re-start the scanner, and try again.

4. Charging issue: Cradle works as charger when putting scanner on it.

Even if the scanner's battery is full, the cradle will continue to supply

power to the scanner. We suggest you to remove scanner from cradle

when scanner is charged fully

*Note: Please install PL-2303 driver for iCR6307AB

LED Indicator Information

Orange LED ON Full charged

Orange LED Flashing Charging / Low battery

Red LED ON Offline / out of service

Green LED ON Good read

Remark:

*When the battery power is too low, the Orange LED will flash and beep once.

Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before turning it

back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A8 for iCR6307ABU or B1 to B8 for iCR6307AB)

iCR6307

BU iCR6307

A1 B1

A2 B2

A3 B3

A4 B4

A5 B5

A6 B6

A7 B7

A8 B8

*Note: Please install PL-2303 driver for iCR6307AB

Trigger Mode

Trigger always

(Trigger available at any time)

Trigger standard (Default)

(Trigger available, after data sent to the device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

High-speed Ultra Slow-speed

Transmission

1transmission

Middle-speed Ultra Slow-speed

Transmission

(Default)

2transmission

Slow-speed Ultra Slow-speed

Transmission 3transmission

Wireless Auto-connection

Wireless Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Wireless Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode. Once you are

back within range, press trigger to connect to the

device. (Default)

2

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway France

Germany

ietnam

Sweden Spain

Denmark Portugal

Switzerland Hungary

Power-saving Mode

Power-saving mode OFF

Powe

-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Powe

-saving mode ON :

Enter power-saving mode after 10-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

*When charging, the scanner will not enter power-saving mode automatically.

How to append a “prefix” or a “suffix” to the

barcode data

prefix suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

1 7

2 8

3 9

Prefix & Suffix TABLE

HEX HID

(SPP) HEX HID

(SPP) HEX HEX HEX HEX

01 CTRL A

(SOH) 19 CTRL Y

(EM) 20 SPACE 38 8 50 P 68 h

02 CTRL B

(STX) 1A CTRL

Z(SUB) 21 ! 39 951 Q 69 i

03 CTRL C

(ETX) 1B ESC

(ESC) 22 " 3A : 52 R 6A j

04 CTRL D

(EOT) 1C CTRL \

(FS) 23 # 3B ;53 S 6B k

05 CTRL E

(ENQ) 1D CTRL ]

(GS) 24 $ 3C < 54 T 6C l

06 CTRL F

(ACK) 1E CTRL ^

(RS) 25 % 3D =55 U 6D m

07 CTRL G

(BEL) 1F CTRL _

(US) 26 & 3E > 56 V 6E n

08 Backspace

(BS) 27 ' 3F ?57 W 6F o

09 Tab

(HT) 28 ( 40 @ 58 X 70 p

0A CTRL J

(LF) 29 ) 41 A59 Y 71 q

0B CTRL K

(VT) 2A * 42 B 5A Z 72 r

0C CTRL L

(FF) 2B + 43 C5B [ 73 s

0D Enter

(CR) 2C , 44 D 5C \ 74 t

0E CTRL N

(SO) 2D - 45 E5D ] 75 u

0F CTRL O

(SI) 2E . 46 F 5E ^ 76 v

10 CTRL P

(DLE) 2F / 47 G5F _ 77 w

11 CTRL Q

(DC1) 30 0 48 H 60 ` 78 x

12 CTRL R

(DC2) 31 1 49 I61 a 79 y

13 CTRL S

(DC3) 32 2 4A J 62 b 7A z

14 CTRL T

(DC4) 33 3 4B K63 c 7B {

15 CTRL U

(NAK) 34 4 4C L 64 d 7C |

16 CTRL V

(SYN) 35 5 4D M65 e 7D }

17 CTRL W

(ETB) 36 6 4E N 66 f 7E ~

18 CTRL X

(CAN) 37 7 4F O67 g

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration End

Configuration

1D Symbologies – 1

ENABLE CODE 39 DISABLE

ENABLE GS1-128

UCC/EAN-128

DISABLE

ENABLE EAN-8 DISABLE

ENABLE EAN-13 DISABLE

1D Symbologies – 2

ENABLE CODE 93 DISABLE

ENABLE CODE 11 DISABLE

ENABLE ISSN DISABLE

ENABLE ISBN DISABLE

ENABLE UPC-E DISABLE

ENABLE UPC-A

DISABLE

ENABLE Interleaved

DISABLE

ENABLE Matrix 25 DISABLE

ENABLE Industrial 25 DISABLE

1D Symbologies – 3

ENABLE CODABAR DISABLE

ENABLE CODE 128 DISABLE

ENABLE MSI DISABLE

ENABLE GS1-Databar

(RSS) DISABLE

ENABLE GS1-Databar

(RSS-Limited) DISABLE

ENABLE GS1-Databar

(RSS-Expand) DISABLE

Quick guide is subject to change without notice. R_151125_02

4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC FS5107A Bedienungsanleitung

RIOTEC

RIOTEC OM7228J Bedienungsanleitung

RIOTEC

RIOTEC OM7320 Bedienungsanleitung

RIOTEC

RIOTEC DC9253AP Bedienungsanleitung

RIOTEC

RIOTEC LS6320E Bedienungsanleitung

RIOTEC

RIOTEC iLS6302ABQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6300FBQ Bedienungsanleitung

RIOTEC

RIOTEC iCR6300CBQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9277L Bedienungsanleitung

RIOTEC

RIOTEC LS6307L Bedienungsanleitung

RIOTEC

RIOTEC FS5100D Bedienungsanleitung

RIOTEC

RIOTEC iLS6303XBU Bedienungsanleitung

RIOTEC

RIOTEC iDC9508K Bedienungsanleitung

RIOTEC

RIOTEC iDC9608K Bedienungsanleitung

RIOTEC

RIOTEC iDC9607A Bedienungsanleitung

RIOTEC

RIOTEC iLS6302KS Bedienungsanleitung

RIOTEC

RIOTEC OM722QJ Bedienungsanleitung

RIOTEC

RIOTEC iDC9607L Bedienungsanleitung

RIOTEC

RIOTEC FS5108J Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6307LS Bedienungsanleitung

RIOTEC

RIOTEC LS6300 Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J BQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6307LBM Bedienungsanleitung

RIOTEC

RIOTEC DC9277A Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iCR6307AB Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken