Rockwell Automation 2711P-RPA Bedienungsanleitung

Installation Instructions

Logic Module, Internal CompactFlash, and RAM

Catalog Numbers 2711P-Rxxxx

About the Components

This document provides information on how to install these components:

•Logic module on a PanelView Plus or PanelView Plus CE device

•Memory (RAM and internal CompactFlash) in the logic module

For complete information on installing, wiring, and troubleshooting the terminals, refer to the

publications listed under Additional Resources.

This document refers to FactoryTalk View ME software that was previously named RSView

ME software.

Topic Page

About the Components 1

Important User Information 2

Safety Precautions 3

About the Logic Module 3

Electrostatic discharge (ESD) wristband 5

Install or Replace RAM 7

Install or Replace the Internal CompactFlash 8

Marine Applications 11

Install a Logic Module 12

Replace a Logic Module 13

Additional Resources 14

www.aotewell.com [email protected]

2Logic Module, Internal CompactFlash, and RAM

Publication 2711P-IN004J-EN-P - September 2009

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that surfaces may reach dangerous temperatures.

Logic Module, Internal CompactFlash, and RAM 3

Publication 2711P-IN004J-EN-P - September 2009

Safety Precautions

Before installing or replacing components and modules, disconnect power from the terminal.

During the installation, be careful not to touch any of the exposed electronic components.

About the Logic Module

The logic module has these features:

•Status indicators

•Input power, DC or AC

•Ethernet port, serial port, two USB ports, CompactFlash card slot

•RAM and internal CompactFlash with firmware or operating system

Logic modules are available as separate catalog numbers for field installation and are shipped

with or without memory installed. If RAM and internal CompactFlash are ordered separately,

you must install these components before attaching the logic module to the display module.

SHOCK HAZARD Disconnect all power from the terminal before installing or replacing any components.

Failure to disconnect power may result in electrical shock or damage to the terminal.

ATTENTION Be careful when touching any of the exposed electronic components to prevent damage

from electrostatic discharge (ESD). Work in a static free environment and wear a properly

grounded ESD wristband.

Logic Module

Display Module

www.aotewell.com [email protected]

4Logic Module, Internal CompactFlash, and RAM

Publication 2711P-IN004J-EN-P - September 2009

PanelView Plus and PanelView Plus CE Logic Modules

Cat. No. Description

PanelView Plus or PanelView Plus CE 700 to 1500 Logic Modules (1)

(1) These logic modules are compatible with any of the 2711P-RWxinternal CompactFlash cards.

2711P-RP Logic module without flash/RAM memory, DC input

2711P-RPA Logic module without flash/RAM memory, AC input(2)

(2) These logic modules are approved for marine applications.

2711P-RPD Logic module without flash/RAM memory, isolated DC input(2)

PanelView Plus 700 to 1500 Logic Modules

2711P-RP1 Logic module with 64 MB flash/64 MB RAM, DC input

2711P-RP1A Logic module with 64 MB flash/64 MB RAM, AC input(2)

2711P-RP1D Logic module with 64 MB flash/64 MB RAM, isolated DC input(2)

2711P-RP2 Logic module with 128 MB flash/128 MB RAM, DC input

2711P-RP2A Logic module with 128 MB flash/128 MB RAM, AC input(2)

2711P-RP2D Logic module with 128 MB flash/ 128 MB RAM, isolated DC input(2)

2711P-RP2DK Conformal-coated logic module with 128 MB flash/128 MB RAM, isolated DC input

2711P-RP2K Conformal-coated logic module with 128 MB flash/128 MB RAM, DC input

2711P-RP3 Logic module with 256 MB flash/256 MB RAM, DC input

2711P-RP3A Logic module with 256 MB flash/256 MB RAM, AC input(2)

2711P-RP3D Logic module, 256 MB flash/256 RAM, isolated DC input(2)

PanelView Plus CE 700 to 1500 Logic Modules

2711P-RP6 PanelView Plus CE logic module with 128 MB flash/128 MB RAM, DC input

2711P-RP6A PanelView Plus CE logic module with 128 MB flash/128 MB RAM, AC input(2)

2711P-RP6D PanelView Plus CE logic module with 128 MB flash/128 MB RAM, isolated DC input(2)

2711P-RP6K PanelView Plus CE conformal-coated logic module with 128 MB Flash/128 MB RAM, DC input

2711P-RP6DK PanelView Plus CE conformal-coated logic module with 128 MB flash/128 MB RAM, isolated

DC input

2711P-RP7 PanelView Plus CE logic module with 256 MB flash/256 MB RAM, DC input

2711P-RP7A PanelView Plus CE logic module with 256 MB flash/256 MB RAM, AC input(2)

2711P-RP7D PanelView Plus CE logic module with 256 MB flash/256 MB RAM, isolated DC input(2)

www.aotewell.com [email protected]

Logic Module, Internal CompactFlash, and RAM 5

Publication 2711P-IN004J-EN-P - September 2009

Required Tools

The following tools are required for installation:

•#1 and #2 Phillips screwdriver

•Electrostatic discharge (ESD) wristband

Component Compatibility for PanelView Plus CE Terminals

It is important to match the series of the internal CompactFlash card with the correct series

of the logic module and software version. The series of the CompactFlash determines the

version of FactoryTalk View ME software and version of the operating system. The logic

module is available with or without memory installed.

Logic Module Compatibility

6189-RPx, 6189-RPRHx, 6189-RPEHx,

2711P-RPx, 2711P-RPx, 2711P-RP6x,

2711P-RP7x

Internal CompactFlash

6189-RW2, 6189-RW3,

6189-RW4, 2711P-RW6,

2711P-RW7, 2711P-RW8

FactoryTalk View ME and

OS Software Version

Series A: 6189-RPxH/A(1)

(1) When upgrading from FactoryTalk View ME software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is

recommended.

Series B: 6189-RWx/B FactoryTalk View ME 3.0

Windows CE 3.0

Series B: 6189-RPxH/B Series C: 6189-RWx/C FactoryTalk View ME 3.10

Windows CE 4.1

Series B: 6189-RPxH/B

Series C: 6189-RPxH/C

Series D: 6189-RPxH/D

Series E: 6189-RPxHx/E

Series F: 2711P-RPxx/F(2)

Series G: 2711P-RPxxx/G(2)

(2) Series F and later logic modules work with PanelView Plus and PanelView Plus CE CompactFlash cards.

Series D: 6189-RWx/D

Series E: 6189-RWx/E

FactoryTalk View ME 3.20

Windows CE 4.1

Series F: 6189-RWx/F

Series G: 6189-RWx/G

Series H: 2711P-RWx/H

FactoryTalk View ME 4.0

Windows CE 4.1

Series J: 2711P-RWx/J FactoryTalk View ME 5.0 or 5.1

Windows CE 4.1

www.aotewell.com [email protected]

6Logic Module, Internal CompactFlash, and RAM

Publication 2711P-IN004J-EN-P - September 2009

Component Compatibility for PanelView Plus Terminals

It is important that you match the series of the internal CompactFlash card with the correct

series of the logic module and software version. The series of the CompactFlash determines

the version of FactoryTalk View ME software. The logic module is available with or without

memory installed.

Compatibility After Upgrade

FactoryTalk View ME terminals are compatible with .MER applications that are the same or a

previous revision. For example, FactoryTalk View ME 3.20 terminals can run .MER

applications for FactoryTalk View ME software, versions 3.0, 3.10, and 3.20.

For PanelView Plus CE devices, the appropriate changes are made to the OS, from Windows

CE software, version 3.0 to 4.1, when upgrading from FactoryTalk View ME software,

version 3.0 to 3.10 or later.

Logic Module Compatibility

2711P-RPx, 2711P-RP1x,

2711P-RP2x, 2711P-RP3x

Internal CompactFlash

2711P-RW1, 2711P-RW2,

2711P-RW3

FactoryTalk View ME

Software Version

Series A: 2711P-RPx/A(1)

(1) Series A logic modules are compatible with series B CompactFlash cards. When upgrading from FactoryTalk View ME

software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is required.

Series B: 2711P-RWx/B FactoryTalk View ME 3.0

Series B: 2711P-RPx/B Series C: 2711P-RWx/C FactoryTalk View ME 3.10

Series B: 2711P-RPx/B

Series C: 2711P-RPx/C

Series D: 2711P-RPx/D

Series E: 2711P-RPxx/E

Series F: 2711P-RPxx/F(2)

Series G: 2711P-RPxxx/G(2)

(2) Series F and later logic modules work with PanelView Plus and PanelView Plus CE CompactFlash cards.

Series D: 2711P-RWx/D

Series E: 2711P-RWx/E

FactoryTalk View ME 3.20

Series F: 2711P-RWx/F

Series G: 2711P-RWx/G

Series H: 2711P-RWx/H

FactoryTalk View ME 4.0

Series J: 2711P-RWx/J FactoryTalk View ME 5.0 or 5.1

Logic Module, Internal CompactFlash, and RAM 7

Publication 2711P-IN004J-EN-P - September 2009

Install or Replace RAM

The logic module is available with or without RAM installed. If ordered separately, you must

install the RAM before attaching the logic module to the display module.

RAM Memory Modules

Follow these steps to install or replace RAM.

1. Turn the logic module over to expose the circuit board.

2. Locate the RAM module on the circuit board.

3. Pull the metal retaining clips away from the module and slide out the RAM module.

4. Insert the new RAM module at a 45° angle and snap down.

Cat. No. Description

2711P-RR64 64 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals

2711P-RR128 128 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals

2711P-RR128K Conformal-coated 128 MB SODIMM RAM for PanelView Plus and PanelView

Plus CE terminals

2711P-RR256 256 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals

RAM

Module

CompactFlash Card

Retaining Clip

Screw

Retaining Clips

8Logic Module, Internal CompactFlash, and RAM

Publication 2711P-IN004J-EN-P - September 2009

Install or Replace the Internal CompactFlash

The logic module is available with or without CompactFlash installed. If ordered separately,

you must install the CompactFlash before attaching the logic module to the display module.

Internal CompactFlash

Follow these steps to replace the internal CompactFlash.

1. Turn the logic module over to expose the circuit board.

2. Unscrew and remove the retaining clip that secures the internal CompactFlash card.

3. Pull out the internal CompactFlash card.

4. Insert the new internal CompactFlash card.

5. Reattach the retaining clip.

Cat. No.(1)

(1) The 2711P-RP, 2711P-RPD, and 2711P-RPA logic modules are compatible with any of the internal CompactFlash options.

Description

2711P-RW1 64 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus

logic modules

2711P-RW2 128 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus

logic modules

2711P-RW3 256 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus

logic modules

2711P-RW6 128 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE

logic modules

2711P-RW7 256 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE logic

modules

2711P-RW8 512 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE logic

modules

www.aotewell.com [email protected]

Logic Module, Internal CompactFlash, and RAM 9

Publication 2711P-IN004J-EN-P - September 2009

Battery Precautions

Replace the Battery in PanelView Plus Terminals

Follow these steps to replace the battery in the logic module of PanelView Plus or PanelView

Plus CE terminals.

1. Disconnect power from the terminal.

2. Place the terminal, display side down, on a flat stable surface.

3. Detach the communication module, if attached, from the logic module by removing

the four screws.

4. Loosen the six captive screws that attach the logic module to the display module.

5. Carefully lift the logic module away from the terminal and turn over to expose the

circuit board.

WARNING When you connect or disconnect the battery, an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure that power is removed or the

area is nonhazardous before proceeding.

For safety information on the handling of lithium batteries, including handling and

disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication

AG 5-4. Replace the battery only with the indicated catalog number.

Do not dispose of battery in a fire or incinerator. Dispose of used batteries in accordance

with local regulations.

Store batteries in a cool, dry environment. We recommend 25 °C (77 °F) with 40…60%

relative humidity. You may store batteries for up to 30 days between -45…85 °C

(-49…185 °F), such as during transportation. To avoid possible leakage, do not store

batteries above 60 °C (140 °F) for more than 30 days.

Logic Module

Communication Module

Screw

Captive

Screw

Display Module

10 Logic Module, Internal CompactFlash, and RAM

Publication 2711P-IN004J-EN-P - September 2009

6. Locate the battery on the circuit board.

7. Remove the battery by lifting up the side of the battery.

8. Insert the new battery.

9. Reattach the logic module by aligning the two connectors on the bottom of the

module with the connectors on the terminal.

10. Push down on the logic module until it is firmly seated.

11. Tighten the six captive screws that secure the logic module to a torque of 0.58 N•m

(5…7 lb•in).

12. Reattach the communication module, if necessary, and tighten the four screws to a

torque of 0.58 N•m (5…7 lb•in).

Lift up the edge of the

battery indicated by

the arrow.

www.aotewell.com [email protected]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation ControlLogix 1756 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix DeviceNet... Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-IV16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLSBATASSY3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1756-DM Series Leitfaden

Rockwell Automation

Rockwell Automation Micro800 2080-MEMBAK-RTC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley POINT I/O B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-M02AE Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley 1770-KFC15 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SLC ControlNet 1747-SCNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Sprecher + Schuh CEP7 Benutzerhandbuch

Rockwell Automation

Rockwell Automation Trusted TMR Expander Interface Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-BOOLEAN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungsanleitung

Rockwell Automation

Rockwell Automation D2-3563 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung