Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Publication 1756-IN588A-EN-P - February 2004

Installation Instructions

EtherNet/IP Web Server Module

Catalog Number 1756-EWEB

Use this manual as a guide to install the EtherNet/IP®We b Ser ve r Modu le.

Note that this document covers hardware installation and some configuration

procedures to get you started. Refer to the EtherNet/IP Web Server Module User

Manual, publication number ENET-UM527, for more detailed configuration

information.

The following table lists the contents of this document and where to find

specific information.

Topic See Page

Important User Information 2

Environment and Enclosure 2

Preventing Electrostatic Discharge 4

European Hazardous Location Approval 4

North American Hazardous Location Approval 5

Identify Module Components 8

Prepare the Chassis for Module Installation 9

Determine Module Slot Location 10

Install the Module 11

Using the Web Server Module 19

Troubleshooting the Module 25

Where to Find More Information on Configuring the Module 26

Specifications 27

Rockwell Automation Support 30

2EtherNet/IP Web Server Module

Publication 1756-IN588A-EN-P - February 2004

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell

Automation sales office or online at http://www.ab.com/manuals/gi) describes some

important differences between solid state equipment and hard-wired electromechanical

devices. Because of this difference, and also because of the wide variety of uses for solid

state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular installation,

Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on

the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission

of Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage, or

economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury or

death, property damage, or economic loss. Attentions help you:

•identify a hazard

•avoid a hazard

•recognize the consequence

SHOCK HAZARD Labels may be located on or inside the drive to alert people that dangerous voltage may

be present.

BURN HAZARD Labels may be located on or inside the drive to alert people that surfaces may be

dangerous temperatures.

EtherNet/IP Web Server Module 3

Publication 1756-IN588A-EN-P - February 2004

Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR Publication 11. Without appropriate precautions,

there may be potential difficulties ensuring electromagnetic compatibility in

other environments due to conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be mounted

within an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The interior of the enclosure

must be accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific enclosure

type ratings that are required to comply with certain product safety

certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by different

types of enclosure. Also, see the appropriate sections in this publication, as

well as the Allen-Bradley publication 1770-4.1 ("Industrial Automation Wiring

and Grounding Guidelines"), for additional installation requirements

pertaining to this equipment.

4EtherNet/IP Web Server Module

Publication 1756-IN588A-EN-P - February 2004

Preventing Electrostatic Discharge

European Hazardous Location Approval

European Zone 2 Certification (The following applies when the product

bears the EEx Marking)

This equipment is intended for use in potentially explosive atmospheres as

defined by European Union Directive 94/9/EC.

The LCIE (Laboratoire Central des Industries Electriques) certifies that this

equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3

equipment intended for use in potentially explosive atmospheres, given in

Annex II to this Directive. The examination and test results are recorded in

confidential report No. 28 682 010.

ATTENTION This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle this

equipment:

•Touch a grounded object to discharge potential

static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component

boards.

•Do not touch circuit components inside the

equipment.

•If available, use a static-safe work station.

•When not in use, store the equipment in

appropriate static-safe packaging.

EtherNet/IP Web Server Module 5

Publication 1756-IN588A-EN-P - February 2004

Compliance with the Essential Health and Safety Requirements has been

assured by compliance with EN 50021.

North American Hazardous Location Approval

The following information applies when operating this equipment in

hazardous locations:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I

Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with markings on the rating

nameplate indicating the hazardous location temperature code. When

combining products within a system, the most adverse temperature code

(lowest "T" number) may be used to help determine the overall temperature

code of the system. Combinations of equipment in your system are subject to

IMPORTANT When using this equipment, consider the following:

•This equipment is not resistant to sunlight or other

sources of UV radiation.

•The secondary of a current transformer shall not be

open-circuited when applied in Class I, Zone 2

environments.

•Equipment of lesser Enclosure Type Rating must be

installed in an enclosure providing at least IP54

protection when applied in Class I, Zone 2

environments.

•This equipment shall be used within its specified

ratings defined by Allen-Bradley.

•Provision shall be made to prevent the rated voltage

from being exceeded by transient disturbances of

more than 40% when applied in Class I, Zone 2

environments.

6EtherNet/IP Web Server Module

Publication 1756-IN588A-EN-P - February 2004

investigation by the local Authority Having Jurisdiction at the time of

installation.

Informations sur l’utilisation de cet équipement en environnements

dangereux:

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une

utilisation en environnements de Classe I Division 2 Groupes A, B, C, D

dangereux et non dangereux. Chaque produit est livré avec des marquages sur

sa plaque d'identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont combinés dans

un système, le code de température le plus défavorable (code de température

le plus faible) peut être utilisé pour déterminer le code de température global

WARNING EXPLOSION HAZARD

•Do not disconnect equipment unless power has

been removed or the area is known to be

nonhazardous.

•Do not disconnect connections to this equipment

unless power has been removed or the area is

known to be nonhazardous. Secure any external

connections that mate to this equipment by using

screws, sliding latches, threaded connectors, or

other means provided with this product.

•Substitution of components may impair suitability

for Class I, Division 2.

•If this product contains batteries, they must only be

changed in an area known to be nonhazardous.

EtherNet/IP Web Server Module 7

Publication 1756-IN588A-EN-P - February 2004

du système. Les combinaisons d'équipements dans le système sont sujettes à

inspection par les autorités locales qualifiées au moment de l'installation.

AVERTISSEMENT RISQUE D’EXPLOSION

•Couper le courant ou s’assurer que

l’environnement est classé non dangereux

avant de débrancher l’équipement.

•Couper le courant ou s’assurer que

l’environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet

équipement à l’aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

•La substitution de composants peut rendre cet

équipement inadapté à une utilisation en

environnement de Classe I, Division 2.

•S’assurer que l’environnement est classé non

dangereux avant de changer les piles.

8EtherNet/IP Web Server Module

Publication 1756-IN588A-EN-P - February 2004

Identify Module Components

Use the following figure to identify the external features of the 1756-EWEB

module.

LINK NET OK

31272-M

Backplane

Connector

Front View

Front

Panel

Side View

Bottom View

Front

Module

RJ45 Cable

Connector located

on underside of module

Backplane

Connector

Web +

MAC ID Label (may be inside here or

at bottom as shown below)

MAC ID Label (may be inside here

or at top as shown above)

EtherNet/IP Web Server Module 9

Publication 1756-IN588A-EN-P - February 2004

Prepare the Chassis for Module Installation

Before you install the module, you must install and connect a ControlLogixTM

chassis and power supply.

For information on installing these products, refer to the publications listed in

the following table.

Chassis

Type

Chassis

Installation

Power

Supply

Power Supply

Installation

Series B: 1756-A4, -A7, -A10, -A13 Pub. No.

1756-IN080

1756-PA72/B Pub. No.

1756-5.67

1756-PB72/B

1756-PA75/A Pub. No.

1756-5.78

1756-PB75/A

20805

1756-A4

Chassis

Power

Supply

10 EtherNet/IP Web Server Module

Publication 1756-IN588A-EN-P - February 2004

Determine Module Slot Location

You can install the module in any slot in the ControlLogix chassis. You can

also install multiple 1756-EWEB modules in the same chassis. The figure

below shows chassis slot numbering in a 4-slot chassis. Slot 0 is the first slot

and is always the left-most slot in the rack (the first slot to the right of the

power supply).

WARNING When you insert or remove the module while

backplane power is on, an electrical arc can occur. This

could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is

nonhazardous before proceeding. Repeated electrical

arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may

create electrical resistance that can affect module

operation.

Power Supply

Slot 0

Slot 1

Slot 2

Slot 3

Chassis

Andere Handbücher für Allen-Bradley 1756-EWEB

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 1746-HSCE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DM2 Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1762-OW16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted CS300 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster MSR41 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-BOOLEAN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Bulletin 193 E1 PLUS Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation SILVER Technology HARRY HI 1734-WS Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLBRED20 SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1797-IE8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSCAP24-6 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Sprecher + Schuh CEP7 Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX Integra Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-HYD02 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung