Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Publication 1756-IN611A-EN-P - February 2010

Installation Instructions

FactoryTalk Historian Machine Edition

Module

Catalog Number 1756-HIST1G and 1756-HIST2G

Use this document as a guide to install the FactoryTalk Historian Machine

Edition Module. Note that this document describes hardware installation

only. For configuration information, refer to the FactoryTalk Historian ME

User’s Guide, publication number 1756-UM611A-EN-E, available on the

FactoryTalk Historian ME Installation CD.

The following table lists the contents of this document and where to find

specific information.

Topic See Page

Important User Information 3

Environment and Enclosure Information 4

Prevent Electrostatic Discharge Information 4

Removal and Insertion Under Power (RIUP) Capability 5

North American Hazardous Location Approval 6

North American Hazardous Location Approval 7

Identify FactoryTalk Historian ME Module Components 9

Prepare the Chassis for Module Installation 11

Determine Module Slot Location 12

Install the Module in the Chassis 13

Remove or Replace the Module (when applicable) 14

Install or Remove the Module Under Power 15

Wire the Ethernet Connector 16

2FactoryTalk Historian Machine Edition Module

Publication 1756-IN611A-EN-P - February 2010

Connect the Module to the Ethernet Network 16

Apply Chassis Power 17

Check Power Supply and Module Status 17

LED Indicator Information 18

Four-character LED Display 19

Application Status 21

Port (Ethernet) LED Information 23

Where to Find Information on Configuring the Module 23

How to Upgrade and Reinstall the Firmware 22

Specifications 24

Topic See Page

FactoryTalk Historian Machine Edition Module 3

Publication 1756-IN611A-EN-P - February 2010

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State

Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or

online at http://www.ab.com/manuals/gi) describes some important differences between solid

state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid state equipment, all persons responsible for

applying this equipment must satisfy themselves that each intended application of this

equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular installation,

Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the

examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information,

circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of

Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations when

necessary.

WARNING

Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or

death, property damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and

understanding of the product.

Attention

Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you:

•identify a hazard.

•avoid a hazard.

•recognize the consequence.

Shock Hazard

Labels may be located on or inside the equipment (e.g., drive or motor) to alert

people that dangerous voltage may be present.

4FactoryTalk Historian Machine Edition Module

Publication 1756-IN611A-EN-P - February 2010

Environment and Enclosure Information

Burn Hazard

Labels may be located on or inside the equipment (e.g., drive or motor) to alert

people that surfaces may have dangerous temperatures.

Attention

This equipment is intended for use in a Pollution Degree 2 industrial

environment in overvoltage Category II applications (as defined in IEC

publication 60664-1) at altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due

to conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts.The enclosure must have

suitable flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if

non-metallic. The interior of the enclosure must be accessible only by the use

of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by different

types of enclosure. Also, see the appropriate sections in this publication, as

well as the Allen-Bradley publication 1770-4.1 (“Industrial Automation Wiring

and Grounding Guidelines”), for additional installation requirements pertaining

to this equipment.

Important User Information

FactoryTalk Historian Machine Edition Module 5

Publication 1756-IN611A-EN-P - February 2010

Prevent Electrostatic Discharge Information

Attention

This equipment is sensitive to electrostatic discharge, which can cause internal

damage and affect normal operation. Follow these guidelines when you handle

this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when not in

use.

6FactoryTalk Historian Machine Edition Module

Publication 1756-IN611A-EN-P - February 2010

Removal and Insertion Under Power (RIUP) Capability

Ethernet Network Communications Connections

North American Hazardous Location Approval

WARNING

When you insert or remove the module while backplane power is on, an electrical

arc can occur. This could cause an explosion in hazardous location installations. Be

sure that power is removed or the area is nonhazardous before proceeding. Repeated

electrical arcing causes excessive wear to contacts on both the module and its

mating connector. Worn contacts may create electrical resistance that can affect

module operation.

WARNING

If you connect or disconnect the communications cable with power applied to this

module or any device on the network, an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure that power is removed or

the area is nonhazardous before proceeding.

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

Products marked “CL I, DIV 2, GP A,

B, C, D” are suitable for use in Class

I, Division 2 Groups A, B, C, D,

hazardous locations and

nonhazardous locations only. Each

product is supplied with markings on

the rating nameplate indicating the

hazardous location temperature code.

When combining products within a

system, the most adverse temperature

code (lowest “T” number) may be

used to help determine the overall

temperature code of the system.

Combinations of equipment in your

system are subject to investigation by

the local authority having jurisdiction

at the time of installation.

Les produits marqués “CL I, DIV 2, GP A,

B, C, D” ne conviennent qu’à une

utilisation en environnements de Classe I

Division 2 Groupes A, B, C, D dangereux

et non dangereux. Chaque produit est livré

avec des marquages sur sa plaque

d’identification qui indiquent le code de

température pour les environnements

dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de

température le plus défavorable (code de

température le plus faible) peut être utilisé

pour déterminer le code de température

global du système. Les combinaisons

d’équipements dans le système sont

sujettes à inspection par les autorités

locales qualifiées au moment de

l’installation.

FactoryTalk Historian Machine Edition Module 7

Publication 1756-IN611A-EN-P - February 2010

WARNING

EXPLOSION

HAZARD

•Do not disconnect

equipment unless

power has been

removed or the

area is known to

be nonhazardous.

•Do not disconnect

connections to

this equipment

unless power has

been removed or

the area is known

to be

nonhazardous.

Secure any

external

connections that

mate to this

equipment by

using screws,

sliding latches,

threaded

connectors, or

other means

provided with this

product.

•Substitution of

components may

impair suitability

for Class I,

Division 2.

•If this product

contains batteries,

they must only be

changed in an

area known to be

nonhazardous.

AVERTISSEMENT

RISQUE D’EXPLOSION

•Couper le courant

ou s’assurer que

l’environnement est

classé non

dangereux avant de

débrancher

l'équipement.

•Couper le courant

ou s'assurer que

l’environnement est

classé non

dangereux avant de

débrancher les

connecteurs. Fixer

tous les connecteurs

externes reliés à cet

équipement à l'aide

de vis, loquets

coulissants,

connecteurs filetés

ou autres moyens

fournis avec ce

produit.

•La substitution de

composants peut

rendre cet

équipement

inadapté à une

utilisation en

environnement de

Classe I, Division 2.

•S’assurer que

l’environnement est

classé non

dangereux avant de

changer les piles.

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

8FactoryTalk Historian Machine Edition Module

Publication 1756-IN611A-EN-P - February 2010

Identify FactoryTalk Historian ME Module Components

Use the following figures to identify the external features of the FactoryTalk

Historian ME Module.

FactoryTalk Historian ME Module Front View

In the following figure, the FactoryTalk Historian ME Module is shown from

the front view with the four-character LED display, LED indicators (BAT,

STS, OK), and Ethernet port locations identified.

FactoryTalk Historian Machine Edition Module 9

Publication 1756-IN611A-EN-P - February 2010

FactoryTalk Historian ME Module Side View

In the following figure, the FactoryTalk Historian ME Module is shown from

the side view with the backplane and compact flash card slot location

identified.

IMPORTANT

All data on the compact flash card is locked to Historian

ME modules. It cannot be read by any other device.

10 FactoryTalk Historian Machine Edition Module

Publication 1756-IN611A-EN-P - February 2010

Prepare the Chassis for Module Installation

Before you install the module, you must install and connect a ControlLogix

chassis and power supply.

For information on installing these products, refer to the publications listed

below.

Chassis

Type

Chassis

Installation

Power

Supply

Power

Supply

Installation

Series B: 1756-A4, -A7, -A10,

-A13, -A17

Pub. No.

1756-IN080

1756-PA72/B Pub. No.

1756-5.67

1756-PB72/B

1756-PA75/A Pub. No.

1756-5.78

1756-PB75/A

Power

Supply

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Sprecher + Schuh CEP7 Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLBRED20 SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation CENTERLINE 2100 LVMCC Bedienungs- und Wartungshandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 1718 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1734-OE4C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley EtherNet/IP Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 193-EGF Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster MSR41 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1768-L43 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLERED20Y Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLSBATASSY3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 2198-R031 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation DeviceNet ArmorBlock A Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSCAP24-6 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix B Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung