Rockwell Automation Allen-Bradley ArmorBlock 1732E-IB8M8SOER Bedienungsanleitung

ArmorBlock EtherNet/IP Dual

Port 8-point Sequence of

Events Input and Scheduled

Output Modules

Catalog Numbers 1732E-IB8M8SOER, 1732E-OB8M8SR

User Manual Original Instructions

2Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021

ArmorBlock EtherNet/IP Dual Port 8-point Sequence of Events Input and Scheduled Output Modules User Manual

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize

themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to

be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use

or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which

may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage,

or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage

may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach

dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc

Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory

requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021 3

Table of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Who Should Use this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Download Firmware, AOP, EDS, and Other Files . . . . . . . . . . . . . . . . . . . . 7

Studio 5000 Logix Designer Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Summary of Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 1

About ArmorBlock Modules Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Hardware/Software Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Use of the Common Industrial Protocol (CIP). . . . . . . . . . . . . . . . . . . . . . 10

Understand the Producer/Consumer Model . . . . . . . . . . . . . . . . . . . . . . . 10

Specify the Requested Packet Interval (RPI) . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 2

Module Overview and Features Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

EtherNet/IP Network Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction to CIP Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

What is IEEE 1588 PTP (Precision Time Protocol)? . . . . . . . . . . . . . . 13

CIP Sync Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

What is CIP Sync? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

What is Time Stamping? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Introduction to the Sequence of Events Input Module . . . . . . . . . . . . . . 14

High Performance Sequence of Events Applications in the Logix

Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

First Fault Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Time Stamped I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

High Speed Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Motion Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Global Position Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Introduction to Scheduled Output Module . . . . . . . . . . . . . . . . . . . . . . . . 16

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

High Speed Product Reject . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 3

Use the Modules in an

ArmorBlock System

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Differences Between Module and Standard I/O . . . . . . . . . . . . . . . . . . . . 19

Similar Functionality to Standard ArmorBlock. . . . . . . . . . . . . . . . . . . . . 20

Chapter 4

Install Your Module Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Install the Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021

Table of Contents

Set the Network Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Mount the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Wire the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Power Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 5

Configure the Module for Your

EtherNet/IP Network

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Configuration Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Gateway Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Set the Network Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Use the Rockwell Automation BootP/DHCP Utility . . . . . . . . . . . . . . . . . 30

Save the Relation List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Use DHCP Software to Configure Your Module . . . . . . . . . . . . . . . . . . . . 33

Chapter 6

Configure the Module Using

Studio 5000 Logix Designer

Software

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Set Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Create an Example Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Configure Your I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Overview of the Configuration Process in

Studio 5000 Logix Designer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Add a New Bridge and Module to Your Project . . . . . . . . . . . . . . . . . . . . . 37

Add the Local EtherNet/IP Bridge to the I/O Configuration . . . . . . 38

Add the I/O module as a child of the 1756-EN2T module . . . . . . . . . 39

Use the Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Change the Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Download Your Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Edit Your Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Access Module Data in Studio 5000 Logix Designer Software. . . . . . . . 45

Configure Studio 5000 Logix Designer and the 1756-EN2T

Communication Module for CIP Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 7

Common Features of the 1732E-

IB8M8SOER and 1732E-OB8M8SR

Modules

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Communications Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Electronic Keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Module Inhibiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Module Fault Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Fully Configurable via Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Producer/Consumer Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Status Indicator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021 5

Table of Contents

Chapter 8

Specific Features of the 1732E-

IB8M8SOER Sequence of Events

Input Module

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Determine Module Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Operational Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Timestamp Latching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Software-configurable Input Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Sync to Master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Chapter 9

Specific Features of the 1732E-

OB8M8SR Scheduled Output

Module

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Determine Module Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Operational Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Time-Scheduled Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Configurable Point-Level Output Fault States. . . . . . . . . . . . . . . . . . . . . . 56

Output State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Chapter 10

Usethe Sequence of Events Input

and Scheduled Output Modules

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Use the Sequence of Events Input Module . . . . . . . . . . . . . . . . . . . . . . . . . 60

How Does 1732E-IB8M8SOER Store Timestamp Data? . . . . . . . . . . 60

Use Timestamp Latching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Use Timestamp Capture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Operational Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Manage the Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Module Sends Data to the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Copy Relevant Input Data to a Separate Data Structure . . . . . . . . . 69

Acknowledge Timestamp Latching Timestamp Data . . . . . . . . . . . . 70

Sort the Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Propagate a Signal From Input Pin to Ethernet . . . . . . . . . . . . . . . . . 72

Per Point Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Use the Scheduled Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Usage with MAOC Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

I/O Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Schedule Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Chapter 11

Troubleshoot the Module Troubleshoot the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Determine Fault Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Chapter 12

Interpret Status Indicators Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Appendix A

Module Tags Fault and Status Reporting Between the Module and Controllers . . . . 83

Module Tag Names and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Tags Used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

6Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021

Table of Contents

Appendix B

Data Tables Communicate with Your Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Connection Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Appendix C

Connect to Networks via

Ethernet Interface

ArmorBlock Module and Ethernet Communication . . . . . . . . . . . . . . . 101

ArmorBlock Module and PC Connections to the Ethernet Network . 101

Connecting to an Ethernet Network . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

EtherNet/IP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Duplicate IP Address Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Configure Ethernet Communications on the ArmorBlock Module . . 103

Configure Using Studio 5000 Logix Designer Software . . . . . . . . . . . . 104

Enable or Disable the Web Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Configure Using Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Appendix D

ArmorBlock Embedded Web

Server

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Browser Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Enable or Disable the Web Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Access the Home Page of the Web Server . . . . . . . . . . . . . . . . . . . . . . . . . 107

Log On to the Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Navigate the

ArmorBlock I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Access Diagnostic Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021 7

Preface

About This Publication This manual is a reference guide for the 1732E-IB8M8SOER, 1732E-OB8M8SR

modules. It describes the procedures you use to install, wire, troubleshoot,

configure, and use your module.

Rockwell Automation recognizes that some of the terms that are currently

used in our industry and in this publication are not in alignment with the

movement toward inclusive language in technology. We are proactively

collaborating with industry peers to find alternatives to such terms and

making changes to our products and content. Please excuse the use of such

terms in our content while we implement these changes.

Who Should Use this Manual Use this manual if you are responsible for designing, installing, programming,

or troubleshooting control systems that use ArmorBlock® EtherNet/IP™ Dual

Port 8-point Sequence of Events Input and Scheduled Output Modules.

You should have a basic understanding of electrical circuitry and familiarity

with relay logic. If you do not, obtain the proper training before using this

product.

Download Firmware, AOP,

EDS, and Other Files

Download firmware, associated files (such as AOP, EDS, and DTM), and access

product release notes from the Product Compatibility and Download Center at

rok.auto/pcdc.

Studio 5000 Logix Designer

Application

The Studio 5000 Logix Designer® application is the re branding of

RSLogix 5000® software and will continue to be the product to program

Logix 5000™ controllers for discrete, process, batch, motion, safety, and drive

based solutions.

Summary of Changes This publication contains the following new or updated information. This list

includes substantive updates only and is not intended to reflect all changes.

Topic Page

Updated template throughout

Added inclusive language acknowledgment 7

Added section Enable or Disable the Web Server 104, 106

Corrected web server user name and password details 107

8Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021

Preface

Additional Resources These documents contain additional information concerning related products

from Rockwell Automation.

You can view or download publications at rok.auto/literature.

Resource Description

ArmorBlock Dual-Port EtherNet/IP 8-Point Digital Modules 1732E-WD002 Information on wiring the ArmorBlock Dual-Port EtherNet/IP 8-point Digital Modules.

1732E ArmorBlock 2 Port Ethernet Module Installation Instructions,

publication 1732E-IN007 Information on installing the ArmorBlock EtherNet/IP module.

ControlLogix Sequence of Events Module User Manual, publication 1756-UM528 A manual on how to install, configure and troubleshoot the ControlLogix Sequence of Events

module in your ControlLogix application.

EtherNet/IP Embedded Switch Technology Application Guide,

publication ENET-AP005 A manual on how to install, configure and maintain linear and Device Level Ring (DLR) networks

using Rockwell Automation® EtherNet/IP devices with embedded switch technology.

EtherNet/IP Modules in Logix 5000 Control Systems User Manual,

publication ENET-UM001 A manual on how to use EtherNet/IP modules with Logix 5000 controllers and communicate with

various devices on the Ethernet network.

Integrated Architecture and CIP Sync Configuration Application Techniques,

publication IA-AT003 A manual on how to configure CIP Sync with Integrated Architecture products. and applications.

EtherNet/IP Network Devices User Manual, ENET-UM006 Describes how to configure and use EtherNet/IP devices to communicate on the EtherNet/IP

network.

Ethernet Reference Manual, ENET-RM002 Describes basic Ethernet concepts, infrastructure components, and infrastructure features.

System Security Design Guidelines Reference Manual, SECURE-RM001 Provides guidance on how to conduct security assessments, implement Rockwell Automation

products in a secure system, harden the control system, manage user access, and dispose of

equipment.

Industrial Components Preventive Maintenance, Enclosures, and Contact Ratings

Specifications, publication IC-TD002 Provides a quick reference tool for Allen-Bradley® industrial automation controls and

assemblies.

Safety Guidelines for the Application, Installation, and Maintenance of Solid-state

Control, publication SGI-1.1

Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides general

guidelines for the application, installation, and maintenance of solid-state control in the form of

individual devices or packaged assemblies incorporating solid-state components.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website, rok.auto/certifications. Provides declarations of conformity, certificates, and other certification details.

Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021 9

Chapter 1

About ArmorBlock Modules

Overview This chapter is an overview of the ArmorBlock family of modules. You will need

to understand the concepts discussed in this chapter to configure your module

and use it in an EtherNet/IP control system. The following table guides you

where to find specific information in this chapter.

Module Features The module features include:

• Use of EtherNet/IP messages encapsulated within standard TCP/UDP/IP

protocol.

• Common application layer with ControlNet® and DeviceNet®.

• Interfacing via Category 5 rated twisted pair cable.

• Half/full duplex 10 Mbit or 100 Mbit operation.

• Mounting on a wall or panel.

• Communication supported by RSLinx® software.

• IP address assigned via standard DHCP tools.

• I/O configuration via Studio 5000 Logix Designer software.

• No network scheduling required.

• No routing tables required.

• Supports connections from multiple controllers simultaneously.

Hardware/Software

Compatibility

The module and the applications described in this manual are compatible with

the following firmware versions and software releases.

Contact Rockwell Automation if you need software or firmware upgrades to

use this equipment.

Topic Page

Module Features 9

Hardware/Software Compatibility 9

Use of the Common Industrial Protocol (CIP) 10

Understand the Producer/Consumer Model 10

Specify the Requested Packet Interval (RPI) 10

Product Firmware Revision / Software Version

1732E-IB8M8SOER and 1732E-OB8M8SR Firmware revision 1.001 or later

1756-EN2T, 1756-EN2TR, 1756-EN3TR 3.x version when using Studio 5000 Logix Designer v18 or later

Studio 5000 Logix Designer(1)

(1) Studio 5000 Logix Designer is the replacement for RSLogix 5000 (since v21). It provides one software package for discrete,

process, batch, motion, safety and drive-based applications.

18 or later

Studio 5000 Logix Designer Add-on Profile 3.01.01 or later

RSLinx software 2.56 or later

10 Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021

Chapter 1 About ArmorBlock Modules

For a complete ControlLogix® compatibility matrix, see the Integrated

Architecture® and CIP Sync™ Configuration Application Technique,

publication IA-AT003.

Use of the Common

Industrial Protocol (CIP)

The 1732E-IB8M8SOER and 1732E-OB8M8SR modules use the Common

Industrial Protocol (CIP™). CIP is the application layer protocol specified for

EtherNet/IP, the Ethernet Industrial Protocol. It is a message-based protocol

that implements a relative path to send a message from the “producing” device

in a system to the “consuming” devices.

The producing device contains the path information that steers the message

along the proper route to reach its consumers. Because the producing device

holds this information, other devices along the path simply pass this

information; they do not need to store it.

This has two significant benefits:

• You do not need to configure routing tables in the bridging modules,

which greatly simplifies maintenance and module replacement.

• You maintain full control over the route taken by each message, which

enables you to select alternative paths for the same end device.

Understand the Producer/

Consumer Model

The CIP “producer/consumer” networking model replaces the old source/

destination (“master/slave”) model. The producer/consumer model reduces

network traffic and increases speed of transmission. In traditional I/O

systems, controllers poll input modules to obtain their input status. In the CIP

system, input modules are not polled by a controller. Instead, they produce

their data either upon a change of state (CoS) or periodically. The frequency of

update depends upon the options chosen during configuration and where on

the network the input module resides. The input module, therefore, is a

producer of input data and the controller is a consumer of the data.

The controller can also produce data for other controllers to consume. The

produced and consumed data is accessible by multiple controllers and other

devices over the EtherNet/IP network. This data exchange conforms to the

producer/consumer model.

Specify the Requested

Packet Interval (RPI)

The Requested Packet Interval (RPI) is the update rate specified for a

particular piece of data on the network. This value specifies how often to

produce the data for that device. For example, if you specify an RPI of 50 ms, it

means that every 50 ms the device sends its data to the controller or the

controller sends its data to the device.

RPIs are only used for devices that exchange data. For example, a ControlLogix

EtherNet/IP bridge module in the same chassis as the controller does not

require an RPI because it is not a data-producing member of the system; it is

used only as a bridge to remote modules.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation 1734-OE4C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T8834 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DM2 Benutzerhandbuch

Rockwell Automation

Rockwell Automation 1606-XLERED Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1734-IR2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley IntelliVAC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-M02AE Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLBRED20 SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1718 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 ATEX Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SLC 500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 794-IRT8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLERED20Y Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX Integra Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation SILVER Technology HARRY HI 1734-WS Bedienungsanleitung

Rockwell Automation

Rockwell Automation AB quality Allen-Bradley 1746-INT4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 Series Handbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung