Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Publication 1756-IN001A-US-P - May 2000

Installation Instructions

ControlLogix

Multi-Vendor Interface Module

Catalog Number 1756-MVI

Use this manual as a guide to install the ControlLogix™

Multi-Vendor Interface Module. The following table identifies what

this manual contains and where to find specific information.

Topic See Page

European Communities (EC) Directive Compliance 3

Preventing Electrostatic Discharge 4

Identify Module Components 5

Prepare the Chassis for Module Installation 6

Identify Module Features 6

Set the Configuration Jumpers 7

Determine Module Slot Location 9

Install the Module in the Chassis 10

Remove or Replace the Module (when applicable) 11

Installing or Removing the Module While Power Is Applied 12

Install the Serial Adapter Cables 12

Apply Chassis Power 14

Check Power Supply and Module Status 14

Reading the Status Indicators 15

Perform a Quick Start 16

Connect the Console 16

Configure the Module 16

Test the Module 18

Specifications 19

CUL Hazardous Location Approval 20

2ControlLogix Multi-Vendor Interface Module

Publication 1756-IN001A-US-P - May 2000

Throughout this manual we use the following note to make you

aware of safety considerations:

Attention statements help you to:

•identify a hazard

•avoid a hazard

•recognize the consequences

We use the following note to call attention to critical information:

Allen-Bradley And ControlLogix are trademarks of Rockwell Automation.

ATTENTION

Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage or economic loss.

IMPORTANT

Identifies information that is critical for successful

application and understanding of the product.

ControlLogix Multi-Vendor Interface Module 3

Publication 1756-IN001A-US-P - May 2000

European Communities (EC) Directive Compliance

If this product has the CE mark it is approved for installation within

the European Union and EEA regions. It has been designed and

tested to meet the following directives.

EMC Directive

This product is tested to meet the Council Directive 89/336/EC

Electromagnetic Compatibility (EMC) by applying the following

standards, in whole or in part, documented in a technical

construction file:

•EN 50081-2 EMC — Generic Emission Standard, Part 2 —

Industrial Environment

•EN 50082-2 EMC — Generic Immunity Standard, Part 2 —

Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage, by applying the safety requirements of EN 61131-2

Programmable Controllers, Part 2 - Equipment Requirements and

Tests. For specific information required by EN 61131-2, see the

appropriate sections in this publication, as well as the Allen-Bradley

publication Industrial Automation Wiring and Grounding Guidelines

For Noise Immunity, publication 1770-4.1.

This equipment is classified as open equipment and must be

mounted in an enclosure during operation to provide safety

protection.

4ControlLogix Multi-Vendor Interface Module

Publication 1756-IN001A-US-P - May 2000

Preventing Electrostatic Discharge

The Multi-Vendor Interface module is sensitive to electrostatic

discharge.

ATTENTION

This module is sensitive to electrostatic discharge.

Electrostatic discharge can damage integrated

circuits or semiconductors if you touch backplane

connector pins. Follow these guidelines when you

handle the module:

•Touch a grounded object to discharge static

potential.

•Wear an approved wrist-strap grounding device.

•Do not touch the backplane connector or

connector pins.

•Do not touch circuit components inside the

module.

•If available, use a static-safe work station.

•When not in use, keep the module in its

static-shield bag.

ControlLogix Multi-Vendor Interface Module 5

Publication 1756-IN001A-US-P - May 2000

Identify Module Components

The 1756-MVI module is shipped with the following six

components:

•1 - 1756-MVI Module

•3 - Serial Adapter Cables

•1 - 1756-MVI Installation Instructions

•1 - CD ROM (1756-MVID only)

Check your order to make sure that you received all of these

components. If you did not receive all of these components, contact

your local Allen-Bradley representative.

1756-MVI Installation Instructions

1756-MVI Module

CD ROM

(1756-MVID only)

Serial Adapter Cables

6ControlLogix Multi-Vendor Interface Module

Publication 1756-IN001A-US-P - May 2000

Prepare the Chassis for Module Installation

Before you install the MVI module, you must install and connect a

ControlLogix chassis (1756-A4, 1756-A7, 1756-A10, or 1756-A13) and

power supply (1756-PA72 or 1756-PB72). To install these products,

refer to publications 1756-5.1 and 1756-5.2.

Identify Module Features

Use the figure below to identify the external features of the module.

20805-M

chassis

power

supply

1756-A4

Chassis

Power

Supply

Backplane

Connector

Channel and

Module Status

Indicators

Door

Port 1

Port 2

Port 3

Wiring

Label

FRONT VIEW

Flash

Card

PRT2PRT3 SETUP

SIDE VIEW

NOTE: Jumpers are located on the back of

circuit board when viewed from this side.

PRT1

PRT2

PRT3

Compact

(Optional)

ControlLogix Multi-Vendor Interface Module 7

Publication 1756-IN001A-US-P - May 2000

Set the Configuration Jumpers

Before installing the 1756-MVI module in the chassis, set the

module’s configuration jumpers on the module’s printed circuit

board.

1. The module ships with the Setup jumper in the Setup position

(see the figure on the following page). The Setup jumper

causes the module to boot with console port PRT1 enabled at

19200 baud, no parity, 8 data bits and 1 stop bit.

Note: When the Setup jumper is removed, the module will

boot with the configuration set in the BIOS Setup Menu. This

configuration is described in detail in the Quick Start section

of this manual. See “Configure the Manual” on page 16.

2. To enable communications on Port 2 and Port 3, place a

jumper in the RS232, RS422, or RS485 position for each port.

The module ships with the jumpers in the RS232 position

(default).

8ControlLogix Multi-Vendor Interface Module

Publication 1756-IN001A-US-P - May 2000

The configuration jumper positions are shown in the following

figure.

PRT2SETUP PRT3

IN = SETUP MODE

OUT = APPLICTION

MODE

RS232

RS422

RS485

RS422

RS232

ControlLogix Multi-Vendor Interface Module 9

Publication 1756-IN001A-US-P - May 2000

Determine Module Slot Location

You can install the module in any slot in the ControlLogix chassis.

You can also install multiple MVI modules in the same chassis. The

figure below shows chassis slot numbering in a 4-slot chassis. Slot 0

is the first slot and is always the leftmost slot in the rack (the first

slot to the right of the power supply).

Power Supply

Slot 0

Slot 1

Slot 2

Slot 3

Chassis

10 ControlLogix Multi-Vendor Interface Module

Publication 1756-IN001A-US-P - May 2000

Install the Module in the Chassis

Align the circuit board with top and

bottom guides in the chassis.

Slide the module into the chassis.

Make sure the module backplane

connector properly connects to the

chassis backplane.

The module is properly installed

when it is flush with the power

supply or other installed modules.

Circuit Board

Andere Handbücher für Allen-Bradley ControlLogix 1756-MVI

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation 2711P-RPA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Bulletin 193 E1 PLUS Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorBlock MaXum 1792D-8BT8PE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation AB quality Allen-Bradley 1746-INT4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1734-IR2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1734-232ASC Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-M02AE Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSCAP24-6 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Kinetix 6000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation 1336 PLUS Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSBUFFER24 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EN2TSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley EtherNet/IP Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung