Rockwell Automation Allen-Bradley DM2 Benutzerhandbuch

Application Technique

Pneumatic Safety Valves Safety Function

Products: GuardLogix Controller, E-stop Button, Safety I/O Module, DM2Pneumatic Safety Valve

Safety Rating: CAT. 3, PLd to ISO 13849-1: 2008

Topic Page

Important User Information 2

General Safety Information 3

Introduction 3

Safety Function Realization: Risk Assessment 4

Pneumatic Safety Valves Safety Function 4

Safety Function Requirements 4

Functional Safety Description 5

Bill of Material 5

Setup and Wiring 5

Configuration 7

Calculation of the Performance Level 15

Verification and Validation Plan 17

Additional Resources 20

2Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016

Pneumatic Safety Valves Safety Function

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are

required to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may

be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss.

Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will

cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for

Personal Protective Equipment (PPE).

Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016 3

Pneumatic Safety Valves Safety Function

General Safety Information

Contact Rockwell Automation to learn more about our safety risk assessment services.

Safety Distance Calculations

Non-separating safeguards provide no physical barrier to prevent access to a hazard. Publications that offer guidance for

calculating compliant safety distances for safety systems that use non-separating safeguards, such as light curtains,

scanners, two-hand controls, or safety mats, include the following:

EN ISO 13855:2010 (Safety of Machinery – Positioning of safeguards with respect to the approach speeds of

parts of the human body)

EN ISO 13857:2008 (Safety of Machinery - Safety distances to prevent hazardous zones being reached by upper

and lower limbs

ANSI B11:19 2010 (Machines – Performance Criteria for Safeguarding)

Separating safeguards monitor a moveable, physical barrier that guards access to a hazard. Publications that offer

guidance for calculating compliant access times for safety systems that use separating safeguards, such as gates with limit

switches or interlocks (including SensaGuard™ switches), include the following:

EN ISO 14119:2013 (Safety of Machinery – Interlocking devices associated with guards - Principles for design

and selection)

EN ISO 13855:2010 (Safety of Machinery – Positioning of safeguards with respect to the approach speeds of

parts of the human body)

EN ISO 13857:2008 (Safety of Machinery - Safety distances to prevent hazardous zones being reached by upper

and lower limbs

ANSI B11:19 2010 (Machines – Performance Criteria for Safeguarding)

In addition, consult relevant national or local safety standards to assure compliance.

Introduction

This safety application technique explains how to wire, configure, and program a Compact GuardLogix controller and

POINT Guard I/O™ module to monitor a dual-channel E-stop device. If the E-stop is actuated, or a fault is detected in

the monitoring circuit, the GuardLogix® controller de-energizes the final control device, in this case, a DM2® pneumatic

safety valve from ROSS Controls.

IMPORTANT This application example is for advanced users and assumes that you are trained and experienced in safety system requirements.

ATTENTION: Perform a risk assessment to make sure that all task and hazard combinations have been identified and addressed.The risk assessment can require

additional circuitry to reduce the risk to a tolerable level. Safety circuits must consider safety distance calculations, which are not part of the scope of this

document.

ATTENTION: While safety distance or access time calculations are beyond the scope of this document, compliant safety circuits must often consider a safety

distance or access time calculation.

4Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016

Pneumatic Safety Valves Safety Function

This example uses a Compact GuardLogix controller, but is applicable to any GuardLogix controller. The Safety

Integrity Software Tool for the Evaluation of Machine Applications (SISTEMA) software calculations that are shown

later in this document must be recalculated if different products are used.

Safety Function Realization: Risk Assessment

The required performance level is the result of a risk assessment and refers to the amount of the risk reduction to be

conducted by the safety-related parts of the control system. Part of the risk reduction process is to determine the safety

functions of the machine. In this application, the performance level required (PLr) by the risk assessment is Category 3,

Performance Level d (CAT. 3, PLd), for each safety function. A safety system that achieves CAT. 3, PLd, or higher, can

be considered control reliable. Each safety product has its own rating and can be combined to create a safety function that

meets or exceeds the PLr.

Pneumatic Safety Valves Safety Function

This application technique includes one safety function: the removal of power or energy from the hazard by actuation of

any of the emergency stop push buttons.

Safety Function Requirements

Pressing any one of the series-wired E-stop buttons stops and prevents hazardous motion by removing power to the

pneumatic safety valve. When the E-stop button is reset, the hazardous motion and power to the pneumatic safety valve

do not resume until a secondary action (the Reset button is pressed and released) occurs. Faults at the E-stop button,

wiring terminals, or safety controller are detected before the next safety demand. This emergency stop function is

complementary to any other safeguards on the machine and does not reduce the performance of other safety-related

functions.

The safety function in this application technique meets or exceeds the requirements for Category 3, Performance Level d

(CAT. 3, PLd), per ISO 13849-1 and control reliable operation per ANSI B11.19.

From: Risk Assessment (ISO 12100)

1. Identification of safety functions

2. Specification of characteristics of each function

3. Determination of required PL (PLr) for each safety function

To: Realization and PL Evaluation

Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016 5

Pneumatic Safety Valves Safety Function

Functional Safety Description

Hazardous motion is interrupted or prevented by actuation of any of the emergency stop buttons (ES1, ES2, or ES3).

Each E-stop is considered a separate safety function. The E-stop buttons are connected in series to a pair of safety inputs

of a safety input module (SI1). The pneumatic safety valve is connected to a pair of safety outputs of a safety output

module (SO1). The I/O modules are connected via CIP Safety™ through an EtherNet/IP™ network to the safety

controller (SC1). The safety code in SC1 monitors the status of the E-stop buttons by using a pre-certified safety

instruction named Dual Channel Input Stop (DCS). When all conditions are satisfied, and no faults are detected on the

input modules, and a Reset button is pressed and released, a secondary certified function block called Configurable

Redundant Output (CROUT) checks the status of the final control device, a pneumatic safety valve. The safety

controller then issues an output signal to the safety output module (SO1) to switch on a pair of safety outputs to energize

the pneumatic safety valve.

Bill of Material

This application technique uses these products.

Setup and Wiring

For detailed information on how to install and wire, refer to the publications listed in the Additional Resources.

System Overview

The 1734-IB8S input module monitors the inputs from the E-stops, which are connected in series.

The 1734-IB8S module can source the 24V DC for all input channels to dynamically test the signal wiring for shorts to

24V DC and channel-to-channel shorts. If a fault occurs, either or both channels are set to low (0), and the controller

reacts by dropping out the pneumatic safety valve. Only after the fault is cleared and the Reset button is pressed and

released does the function block reset.

Cat. No. Description Quantity

800FM-G611MX10 800F reset push button - metal, guarded, blue, R, metal latch mount, one normally-open contact, standard 1

800FM-MT44MX02 800F non-illuminated mushroom operators, twist-to-release, 40 mm (1.58 in.), round metal (type 4/13, IP66), red,

metal latch mount, 0 normally-open contacts, 2 normally-closed contacts, standard, standard pack 1

800F-15YSE112 800F legend plate, 60 mm (2.36 in.) round, universal emergency stop, yellow with black legend text, 22.5 mm (.89

in.) opening 3

DM2CNAxxA21 DM2series pneumatic safety valve – Contact ROSS Controls for proper valve sizing and a specific part number 1

1768-ENBT CompactLogix™ EtherNet/IP bridge module 1

1768-L43S Compact GuardLogix processor, 2.0 MB standard memory, 0.5 MB safety memory 1

1768-PA3 Power supply, 120/240V AC Input, 3.5 A @ 24V DC 1

1769-ECR Right end cap/terminator 1

1734-AENT 24V DC Ethernet adapter 1

1734-TB Module base with removable IEC screw terminals 4

1734-IB8S POINT Guard I/O safety input module 1

1734-OB8S POINT Guard I/O safety output module 1

1783-US05T Stratix 2000™ unmanaged Ethernet switch 1

6Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016

Pneumatic Safety Valves Safety Function

Shorts to 0V DC (and wire off) are seen as an open circuit by the 1734-IB8S input module, and the controller reacts by

dropping out the pneumatic safety valve. If the inputs remain discrepant for longer than the discrepancy time, then the

function block in the controller safety task declares a fault. Only after the fault is cleared, and the Reset button is pressed

and released, does the function block reset.

The final control device is a pneumatic safety valve that is controlled by a 1734-OB8S output module. A feedback circuit

is wired through the normally-open contact and back to an input of the 1734-IB8S module to monitor the pneumatic

safety valve for proper operation. The pneumatic safety valve cannot restart if the feedback circuit is not in the correct

state.

The maximum output current is 1 A for each output point of the 1734-OB8S module.

Primary power consumption for each solenoid is as follows:

•15.8VA inrush

•12.8VA holding on 50 Hz or 60 Hz

•5.8 W on DC

The system has individual Reset buttons for resetting faults and safety outputs. The Reset buttons and the pneumatic

safety valve Ready to Run (N.O. Contacts) and Fault Indicator (N.C. Contacts) are all wired to the 1734-IB8S module

in this example. This configuration is not required for functional safety. These four inputs can be wired to a standard

input module.

Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016 7

Pneumatic Safety Valves Safety Function

Electrical Schematic

Pins 1 and 3 are connected when air pressure is present and the valve is Ready to Run.

If a fault has occurred or pressure is removed from the valve inlet, pins 1 and 2 are connected.

In the event of a fault, remove power from the pilot solenoids (A and B) momentarily, and apply power to the Reset

solenoid to return the valve to Return To Run state. Wait at least 250 ms after removing power from the reset solenoid

before trying to re-energize the pilot solenoids.

Configuration

The Compact GuardLogix controller is configured by using RSLogix 5000® software, version 18 or later. You must first

create a project and add the I/O modules. Then, configure the I/O modules for the correct input and output types. A

detailed description of each step is beyond the scope of this document. Knowledge of the RSLogix™ programming

environment is assumed.

PB2

Fault Reset

PB1

Reset

E-stop 1 E-stop 2 E-stop 3

Air Supply

DM2

Pneumatic

Safety Valve

Air to System

Pin 1: Common

Pin 2: Normally Closed

Pin 3: Normally Open

Pin 4: Not Used

8Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016

Pneumatic Safety Valves Safety Function

Create a Project with a Compact GuardLogix Controller

1. In the RSLogix 5000 software, create a project.

2. In the New Controller dialog box, do the following:

a. From the Type pull-down menu, choose 1768-L43S CompactLogix™ 5343S Safety Controller.

b. From the Revision pull-down menu, choose the appropriate revision for the controller.

c. In the Name box, type an appropriate name for the controller.

d. Click OK.

3. In the Controller Organizer, add the 1768-ENBT module to the 1768 bus.

4. In the Select Module dialog box, select the 1768-ENBT module, and click OK.

Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016 9

Pneumatic Safety Valves Safety Function

5. In the New Module dialog box, do the following:

a. Name the module.

b. Type its IP address.

c. Click OK.

We used 192.168.1.8 for this application example. Yours can be different.

6. In the Controller Organizer, right-click 1768-ENBT module, and choose New Module.

7. In the Select Module dialog box, select the 1734-AENT adapter, and click OK.

10 Rockwell Automation Publication SAFETY-AT128B-EN-P - July 2016

Pneumatic Safety Valves Safety Function

8. In the New Module dialog box, do the following:

a. Name the module.

b. Type its IP address.

c. Click OK.

d. Click Change.

We used 192.168.1.11 for this application example. Yours may be different.

9. From the Chassis Size pull-down menu, choose 3 and click OK.

Chassis size is the number of modules that are inserted in the chassis. The 1734-AENT adapter is considered to be

in slot 0, so for one input and one output module, the chassis size is 3.

10. In the Controller Organizer, right-click the PointIO 3 Slot Chassis adapter and choose New Module.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation DeviceNet ArmorBlock A Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1734-232ASC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1746-BTM Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-BOOLEAN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XBx-EX Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1734-IR2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 20-750-PNET Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1751-SLBA Bedienungsanleitung

Rockwell Automation

Rockwell Automation 193-EGF Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster MSR41 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 2198-R031 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Bulletin 193 E1 PLUS Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 ATEX Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLERED Bedienungsanleitung

Rockwell Automation

Rockwell Automation Kinetix 6000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley IntelliVAC Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung