Rockwell Automation Allen-Bradley PowerFlex 70 Bedienungsanleitung

Logix5000 Control Systems: Connect PowerFlex 70 Drives

over a DeviceNet Network

Catalog Numbers Logix5000 Controllers, PowerFlex 70 Drives

Quick Start

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety

Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from

your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some

important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference,

and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the

use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Allen-Bradley, CompactLogix, ControlLogix, Integrated Architecture, KwikLink, Logix5000, PowerFlex, Rockwell Software, Rockwell Automation, RSLogix, RSNetWorx, and TechConnect are trademarks of Rockwell

Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012 3

Table of Contents

Preface

About This Publication

Before Using This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Other Logix5000 Control System Quick Starts . . . . . . . . . . . . . . . . . . . . . . . 8

Where to Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How Hardware is Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Required Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 1

Prepare the PowerFlex 70 Drive

Hardware

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Follow These Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mount the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Wire Power to the Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Set the Node Address and Communication Rate. . . . . . . . . . . . . . . . . . . . 17

Connect the DeviceNet Adapter to the Drive . . . . . . . . . . . . . . . . . . . . . . 18

Connect the Drive to the DeviceNet Network. . . . . . . . . . . . . . . . . . . . . . 19

Chapter 2

Create DeviceNet Network Software

Files

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Follow These Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Set the 1769-SDN Scanner Module’s Node Address . . . . . . . . . . . . . . . . 26

Create a DeviceNet Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Associate the DeviceNet Configuration File with an

RSLogix 5000 Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Create a DeviceNet Scanlist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 3

Use a PowerFlex 70 Drive in an

RSLogix 5000 Project

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Follow These Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Create DeviceNet Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Download the Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Test the PowerFlex 70 Drive Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012

Table of Contents

Notes:

Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012 5

Preface

About This Publication

This quick start provides examples and procedures for including PowerFlex®70 drives in a

Logix5000controllers control system over a DeviceNet network. The programming examples

are not complex, and offer easy solutions to verify that devices are functioning and

communicating properly.

Before Using This Publication

You can only complete the tasks described in this publication after first completing some

prerequisite tasks with a Logix5000 controller. For example, before you can add a PowerFlex 70

drives to an RSLogix5000 project, as described in Chapter 3, you must first create the project.

For more information on how to complete these tasks with specific Logix5000 controllers, see

the Integrated Architecture: Logix5000 Control Systems Quick Starts Quick Reference,

publication IASIMP-QR024.

IMPORTANT

This publication describes example tasks you complete when using PowerFlex 70 drives on a DeviceNet network. The

tasks described are not the only tasks you can complete with the PowerFlex 70 Drives on a DeviceNet network. You will

likely need to complete additional tasks when using PowerFlex 70 drives in specific Logix5000 control systems.

For more information on how to use the all of the PowerFlex 70 drives’ functionality in specific Logix5000 control

system, see Additional Resources on page 11.

IMPORTANT

Consider the following before using this publication:

•Multiple Logix5000 controllers support the use of a DeviceNet network. The specific hardware used and software

configuration parameter settings vary by Logix5000 controller. This quick starts describes how to use PowerFlex 70

drives over a DeviceNet network in a CompactLogix5370 L3 control system.

The example graphics shown in Table 1 - Required Tasks to Complete before Using This Quick Start on page 6 are for

CompactLogix 5370 L3 controllers. Depending on the Logix5000 controller you are using, the specific steps to

complete the tasks described in the table might vary.

•The tasks described in this publication are written with the assumption that you have already installed the

CompactLogix 5370 L3 control system and it is powered.

6Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012

Preface

This table describes the tasks you must complete before using this publication.

Table 1 - Required Tasks to Complete before Using This Quick Start

Task Description

PreparetheLogix5000

control system

hardware

Assembling the control system and connecting to the DeviceNet network. At minimum, your system must

include a controller, DeviceNet scanner module to access the DeviceNet network and the components required

to install a DeviceNet network. For example, you need an external power source to power a DeviceNet network.

For example purposes, this quick start describes how to use a CompactLogix 5370 L3 controller with a 1769-SDN

scanner module. Your computer accesses the controller via an EtherNet/IP network. The tasks described in

Chapter 2 and Chapter 3 are done so with CompactLogix 5370 L3 controller and 1769-SDN scanner module.

We recommend that you use those components to complete the steps described. If you use a different

Logix5000 controller and DeviceNet scanner module, you can complete the tasks in these chapters but you must

account for any hardware differences.

For more information on installing a DeviceNet network, see the DeviceNet Media Design and Installation Guide,

publication DNET-UM072.

This task does not include installation of remote hardware components, for example, PowerFlex 70 drives,

used over the network included in your application.

Prepare the computer Installing required software, for example RSLogix 5000 software, on your complete

1 (Front)

2 (Rear)

00:00:BC:2E:69:F6

Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012 7

Preface

Configure the network Completing tasks associated with configuring the DeviceNet network with RSNetWorxfor DeviceNet software,

such as setting the node address for the DeviceNet scanner module your controller uses to access the DeviceNet

network.

This quick start uses a CompactLogix 5370 L3 controller with a 1769-SDN scanner module, and the tasks

described in Chapter 2 and Chapter 3 are done so with that controller and scanner module. We recommend that

you use those components and corresponding software files with this quick start.

If you use a different Logix5000 controller and DeviceNet scanner module and corresponding DeviceNet network

software files, you can complete the tasks in Chapter 2 and Chapter 3 but you must account for any software

differences.

Create an

RSLogix 5000 project

Creating a project used with your Logix5000 controller that includes all required control system components.

Your project must include the DeviceNet scanner module used by your controller to access the DeviceNet

network.

This quick start uses a CompactLogix 5370 L3 controller with a 1769-SDN scanner module, and the tasks

described in Chapter 2 and Chapter 3 are done so for that controller and scanner module. We recommend that

you use those components with this quick start.

If you use a different Logix5000 controller and DeviceNet scanner module and corresponding RSLogix 5000

software files, you can complete the tasks in Chapter 2 and Chapter 3 but you must account for any software

differences.

IMPORTANT: For more information on how to create an RSLogix 5000 project that can be associated with your

DeviceNet configuration file, see Associate the DeviceNet Configuration File with an RSLogix 5000 Project.

Table 1 - Required Tasks to Complete before Using This Quick Start

Task Description

8Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012

Preface

Other Logix5000 Control System Quick Starts

This quick start describes how to use a single component-type over a single network in a

Logix5000 control system. Typically, though, a Logix5000 control system includes more than

the controller, communication module, and a single component over a single network.

For example, if a Logix5000 control system operates on a DeviceNet network, the system might

use remote I/O modules, HMI devices, and drives in addition to the controller and

communication modules.

For a complete list of Logix5000 control system quick starts that describe how to use other

devices in Logix5000 control systems, see the Integrated Architecture: Logix 5000 Control

Systems Quick Starts Quick Reference, publication IASIMP-QR024.

The beginning of each chapter contains the following information. Read these sections before

beginning work in each chapter:

•Before You Begin - This section lists the tasks you must complete before starting the

chapter.

•What You Need - This section lists the tools that are required to complete the tasks in the

current chapter. This includes, but is not limited to, hardware and software.

•Follow These Steps - This section illustrates the steps in the current chapter.

Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012 9

Preface

Where to Start

Prepare the PowerFlex 70

Drive Hardware

Required Tasks

Described in the appropriate Logix5000 controller quick start

1. Prepare the Controller Hardware

2. Prepare the Computer

3. Configure the Network

4. Create RSNetWorx for DeviceNet and RSLogix 5000 Software Projects

page 13

Create DeviceNet

Network Software Files

page 21

Logix5000

Controller

Use a PowerFlex 70 Drive in

an RSLogix 5000 Project

page 41

10 Rockwell Automation Publication IASIMP-QS030A-EN-P - July 2012

Preface

How Hardware is Connected

This quick start demonstrates the following Logix5000 control system that uses PowerFlex 70

drives on a DeviceNet network.

Required Software

To complete examples in this quick start, you need this software.

Software Required Software Version, min Required for This Task

RSLogix 5000 20.00.00 or later(1)

(1) RSLogix 5000 software, version 20.00.00 or later, is required for use of this quick start because the example Logix5000 controller, and associated tasks, described herein are completed in a

CompactLogix 5370 L3 control system. CompactLogix 5370 control systems require RSLogix 5000 software, version 20.00.00 or later. If you connect a PowerFlex 70 drive over a DeviceNet network in a

Logix5000 control system that uses a different controller, the minimum software version may differ.

Change RSLogix 5000 projects to use

PowerFlex 70 drives.

RSNetWorx for DeviceNet 11.00.00 Modify DeviceNet configuration file to

include the PowerFlex 70 Drives described in

this publication.

DeviceNet Tag Generator 20.00.00 or later Generate new programs and tags in your

RSLogix 5000 project.

Logix5000

Controller with

DeviceNet

Scanner Module

Computer Connected to

Logix5000 Controller

DeviceNet Power Supply

1606-XLDNET8

PowerFlex 70 Drive with

20-COMM-D Adapter

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-PLUS Bulletin 150 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation 1769-L30ER Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorStart Bulletin 280G Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 7000 Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley G Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation MicroLogix 1000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1336 PLUS Bedienungsanleitung

Rockwell Automation

Rockwell Automation SMC Dialog Plus Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 750-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1502 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 525 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1785 PLC-5 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756 ControlLogix Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 23PFC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 45MLA Bedienungsanleitung

Rockwell Automation

Rockwell Automation ARMORSTART 280D Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch