Rockwell Automation Allen-Bradley 1606-XLP60BQ Bedienungsanleitung

Reference Manual

egaPegaP

1. Intended Use .......................................................3

2. Installation Requirements...................................3

3. AC-Input...............................................................4

4. Input Inrush Current ...........................................5

5. Output .................................................................6

6. Hold-up Time.......................................................7

7. DC-Input...............................................................7

8. Efciency and Power Losses................................8

9. Functional Diagram.............................................9

10. Front Side and User Elements.............................9

11. Terminals and Wiring........................................10

12. Lifetime Expectancy and MTBF.........................10

13. EMC ....................................................................11

14. Environment ......................................................12

15. Protection Features ...........................................13

16. Safety Features ..................................................13

17. Dielectric Strength ............................................14

18. Certications ....................................................15

19. Physical Dimensions and Weight ..................... 16

20. Application Notes ............................................. 17

20.1. Peak Current Capability ...........................17

20.2. Back-feeding Loads ..................................17

20.3. Charging Batteries ...............................18

20.4. External Input Protection .........................18

20.5. Parallel Use to Increase Output Power ....18

20.6. Daisy Chaining of Outputs .......................19

20.7. Inductive and Capacitive Loads ................19

20.8. Series Operation .......................................20

20.9. Operation on Two Phases ........................20

20.10. Use Without PE on the Input ...................20

20.11. Use in a Tightly Sealed Enclosure ............21

20.12. Mounting Orientations ............................22

Bulletin 1606 Switched Mode Power Supplies

CatalogNumber: 1606-XLP60BQ

Index

•PEand symbol—PE is the abbreviation for Protective Earth and has the same meaning as the symbol .

•Earth,Ground—This document uses the term “earth” which is the same as the U.S. term “ground”.

• T.b.d.—To be defined, value or description will follow later.

• AC 230V—A figure displayed with the AC or DC before the value represents a nominal voltage with standard tolerances (usually ±15%)

included. E.g.: DC 12V describes a 12V battery disregarding whether it is full (13.7V) or flat (10V)

• 230Vac—A figure with the unit (Vac) at the end is a momentary figure without any additional tolerances included.

• 50Hz vs. 60Hz—As long as not otherwise stated, AC 230V parameters are valid at 50Hz mains frequency.

•may—A key word indicating flexibility of choice with no implied preference.

•shall—A key word indicating a mandatory requirement.

•should—A key word indicating flexibility of choice with a strongly preferred implementation.

Terminology and Abbreviations

2Rockwell Automation Publication 1606-RM015A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

Power Supply

100-240V Wide Range Input

NEC Class 2 Compliant

Adjustable Output Voltage

Efciency up to 87.2%

Low No-load Losses and Excellent Partial-load Efciency

Compact Design, Width only 45mm

Full Power between -10°C and +60°C

Large International Approval Package

3 Year Warranty

Description

Compact size, light weight, simple installation onto the

DIN rail and the integration of only the highest quality

components are the factors that make this power supply

so easy to deploy and use within seconds.

A rugged electrical and mechanical design as well as a

high immunity against electrical disturbances on the

mains ensure reliable output power. This power

supply offers superior protection for equipment

connected to the public mains network or exposed to

a critical industrial environment.

The XLP family of power supplies offers output voltages

from 5 to 56Vdc and power ratings from 15 to 120W.

Specication Quick Reference

Output voltage DC 12V

Adjustment range 12 - 15V

Output current 4.5A at 12V

3.6A at 15V

Output power 54W

Output ripple < 50mVpp 20Hz to 20MHz

Input voltage AC 100-240V -15% / +10%

AC 100V mains

requires derating

Mains frequency 50-60Hz ±6%

AC Input current 0.91 / 0.54A at 120 / 230Vac

Power factor 0.58 / 0.5 at 120 / 230Vac

AC Inrush current typ. 16 / 32A peak value at 120

/ 230Vac 40°C

and cold start

DC Input 88-375Vdc below 130Vdc

derating required

Efciency 85.3 / 87.2% at 120 / 230Vac

Losses 9.3 / 7.9W at 120 / 230Vac

Temperature range -10°C to +70°C operational

Derating 1.4W/°C +60 to +70°C

Hold-up time typ. 25 / 113ms at 120 / 230Vac

Dimensions 45x75x91mm WxHxD

Weight 250g / 0.55lb

Catalog Numbers

Power Supply 1606-XLP60BQ 12-15V Standard unit

Certication Marks

Ind. Cont. Eq. UL 508

UL 60950-1

Marine

NEC

Class 2

EMC, LVD

Marine RINA

GOST R C-Tick

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

Rockwell Automation Publication 1606-RM015A-EN-P — March 2014 3

Bulletin 1606 Switched Mode Power Supplies

1. Intended Use

•This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office,

communication, and instrumentation equipment.

•Do not use this power supply in equipment where malfunction may cause severe personal injury or threaten human life.

2. Installation Requirements

•This device may only be installed and put into operation by qualified personnel.

•This device does not contain serviceable parts. The tripping of an internal fuse is caused by an internal defect.

•Should damage or malfunction occur during installation or operation, immediately turn power off and send unit to the factory for inspection.

•Mount the unit on a DIN rail so that the terminals are located on the bottom of the unit. For other mounting orientations, refer to derating

requirements in this document.

•This device is designed for convection cooling and does not require an external fan. Do not obstruct airflow and do not cover ventilation grid

(e.g. cable conduits) by more than 30%!

•Keep the following installation clearances: 40mm on top, 20mm on the bottom, 5mm on the left and right sides are recommended when the

device is loaded permanently with more than 50% of the rated power. Increase this clearance to 15mm in case the adjacent device is a heat

source (e.g. another power supply).

SHOCK HAZARD: Do not use the power supply without proper grounding (Protective Earth). Use the terminal on the input

block for earth connection and not one of the screws on the housing.

- Turn power off before working on the device. Protect against inadvertent re-powering

- Make sure that the wiring is correct by following all local and national codes

- Do not modify or repair the unit

- Do not open the unit as high voltages are present inside

- Use caution to prevent any foreign objects from entering the housing

- Do not use in wet locations or in areas where moisture or condensation can be expected

- Do not touch during power-on, and immediately after power-off. Hot surfaces may cause burns.

WARNING: EXPLOSION HAZARDS!

Substitution of components may impair suitability for this environment. Do not disconnect the unit or operate the voltage adjustment or S/P jumper unless

power has been switched off or the area is known to be non-hazardous.

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

4Rockwell Automation Publication 1606-RM015A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

3. AC Input

AC input nom. AC 100-240V -15% / +10%, TN/TT/IT-mains

AC input range

85-264Vac continuous operation,

see Fig. 3-3 for de-rating requirements for AC 100V

mains.

264–300Vac < 0.5s

Allowed voltage L or N to earth max. 264Vac or 375Vdc

Input frequency nom. 50–60Hz ±6%

Turn-on voltage typ. 65Vac

Shut-down voltage typ. see Fig. 3-1

AC 100V AC 120V AC 230V

Input current (rms) typ. 1.06A 0.91A 0.54A at 12V, 4.5A see Fig. 3-3

Power factor *) typ. 0.61 0.58 0.50 at 12V, 4.5A see Fig. 3-4

Crest factor **) typ. 3.2 3.3 3.7 at 12V, 4.5A

Start-up delay typ. 120ms ***) 100ms ***) 90ms see Fig. 3-2

Rise time typ. 40ms 40ms 50ms at 12V, 4.5A, 0mF, see Fig. 3-2

100ms 90ms 110ms at 12V, 4.5A, 4.5mF

Turn-on overshoot max. 200mV 200mV 200mV see Fig. 3-2

*) The power factor is the ratio of the true (or real) power to the apparent power in an AC circuit.

**) The crest factor is the mathematical ratio of the peak value to RMS value of the input current waveform.

***) At low temperatures, start-up attempts may occur which extends the start-up delay time.

Fig. 3-1 Input voltage range Fig. 3-2 Turn-on behavior, denitions

Rated

input range max.

500ms

OUT

300Vac26465

Start-up

delay Rise

Time

Overshoot

- 5%

Output

Voltage

Input

Voltage

Fig. 3-3 Input current vs. output load at 12V Fig. 3-4 Power factor vs. output load at 12V

4.5A

130

0.4

1.2A

Input Current, typ.

0.8

1.0

0.6

0.2

Output Current

1.5 2.5 3.50.5

a) 100Vac

b) 120Vac

c) 230Vac

4.5A

012 4

0.40

0.45

0.50

0.55

0.60

0.65

Power Factor, typ.

a) 100Vac

b) 120Vac

c) 230Vac

Output Current

3.55.05.15.2

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

Rockwell Automation Publication 1606-RM015A-EN-P — March 2014 5

Bulletin 1606 Switched Mode Power Supplies

Fig. 3-5 De-rating requirements for

low input voltages

85Vac

60W

Input Voltage

A...<+45°C

B...<+60°C

90Vac 108Vac

Allowable

Output Power

4. Input Inrush Current

A NTC limits the input inrush current after turn-on of the input voltage. The inrush current is input voltage and

ambient temperature dependent.

The charging current into EMI suppression capacitors is disregarded in the rst microseconds after switch-on.

AC 100V AC 120V AC 230V

Inrush current max. 17A

peak

21A

peak

40A

peak

40°C ambient, cold start

typ. 14A

peak

16A

peak

32A

peak

40°C ambient, cold start

Inrush energy typ. 0.15A

s 0.2A

s 1.0A

s 40°C ambient, cold start

Fig. 4-1 Input inrush current, typical behavior

Fig. 4-2 Input inrush current, zoom into rst peak

Input Voltage

Input Current

Output Voltage

Input Current

Input: 230Vac

Output: 12V, 4.5A

Ambient: 25°C

Input current 2A/DIV

Time basis: 0.5ms / DIV

Input: 230Vac

Output: 12V, 4.5A

Ambient: 25°C

Upper curve: Input current 5A/DIV

Middle curve: Input voltage 100V/DIV

Lower curve: Output voltage 2.5V/DIV

Time basis: 20ms / DIV

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

6Rockwell Automation Publication 1606-RM015A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

5. Output

Output voltage nom. 12V

Adjustment range min. 12-15V guaranteed

max. 16.2V *) at clockwise end position of potentiometer

Factory setting 12.0V ±0.2%, at full load, cold unit

Line regulation max. 10mV 85-264Vac

Load regulation max. 100mV static value, 0A 4.5A

Ripple and noise voltage max. 50mVpp 20Hz to 20MHz, 50Ohm

Output capacitance typ. 3 000μF

Output current nom. 4.5A at 12V, see Fig. 5-1

nom. 3.6A at 15V, see Fig. 5-1

Output power nom. 54W

Short-circuit current min. 6.0A load impedance 250mOhm, see Fig. 5-1

max. 8.0A load impedance 250mOhm, see Fig. 5-1

*) This is the maximum output voltage which can occur at the clockwise end position of the potentiometer due to tolerances. There is no

guarantee this value can be achieved. The typical value is about 15.8V.

Fig. 5-1 Output voltage vs. output current,

typ.

Output Voltage

16V

9A32154

678

Adjustment

Range

Output Current

a) 100Vac

b) 120Vac

c) 230Vac

Peak current capability (up to several milliseconds)

The power supply can deliver a peak current which is higher than the specied short term current. This helps to start

current demanding loads or to safely operate subsequent circuit breakers.

The extra current is supplied by the output capacitors inside the power supply. During this event, the capacitors will be

discharged and causes a voltage dip on the output. Detailed curves can be found in section 22.1.

Peak current voltage dips typ. from 12V to 7V at 9A for 50ms, resistive load

typ. from 12V to 5V at 22.5A for 2ms, resistive load

typ. from 12V to 3.2V at 22.5A for 5ms, resistive load

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

Rockwell Automation Publication 1606-RM015A-EN-P — March 2014 7

Bulletin 1606 Switched Mode Power Supplies

6. Hold-up Time

AC 100V AC 120V AC 230V

Hold-up Time typ. 37ms 56ms 229ms at 12V, 2.25A, see Fig. 6-1

typ. 16ms 25ms 113ms at 12V, 4.5A, see Fig. 6-1

Note: At no load, the hold-up time can be up to several seconds. The green DC-ok lamp is also on at this time.

Fig. 6-1 Hold-up time vs. input voltage Fig. 6-2 Shut-down behavior, denitions

100

120ms

85 120 155 190 230Vac

Input Voltage

Hold-up Time

a) 12V 2.25A typ.

b) 12V 2.25Amin.

c) 12V 4.5A typ.

d) 12V 4.5A min.

a b c

- 5%

Hold-up Time

Zero Transition

Output

Voltage

Input

Voltage

7. DC Input

The power supply can also be supplied from a DC source. Use a battery or similar DC source. For other sources, contact

RA. Connect the + pole to L and the – pole to N. Connect the PE terminal to an earth wire or to the machine ground.

DC input nom. DC 110-300V -20%/+25%

DC input range min. 88-375Vdc continuous operation, reduce output power according

Fig. 7-2 at voltages below 130Vdc

Allowed Voltage L/N to Earth max. 375Vdc IEC 62103

DC input current typ. 0.57A / 0.2A 110Vdc / 300Vdc, at 12V, 4.5A

Turn-on voltage typ. 80Vdc steady state value

Shut-down voltage typ. 30-70Vdc depending on output load

Fig. 7-1 Wiring for DC Input

Fig. 7-2 Allowable output current below

110Vdc input voltage

Load

Power Supply

Battery

internal

fused

60W

80 90 100 110 130Vdc

Input Voltage Vdc

Output Power

120

(b)

(a)

(a) Continuous

(b) Short-term

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

8Rockwell Automation Publication 1606-RM015A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

8. Efciency and Power Losses

AC 100V AC 120V AC 230V

Efciency typ. 83.5% 85.3% 87.2% at 12V, 4.5A (full load)

Power losses typ. 0.45W 0.5W 0.85W at 0A

typ. 4.2W 3.9W 4.2W at 12V, 2.25A (half load)

typ. 10.6W 9.3W 7.9W at 12V, 4.5A (full load)

Fig. 8-1 Efciency vs. output current at 12V,

typ.

Fig. 8-2 Losses vs. output current at 12V,

typ.

Efciency

90%

4.5

0.5 2.521.5

a) 230Vac

b) 120Vac

c) 100Vac

13.534

Output Current

Power Losses

12W

4.5A0.5 2.5 3.51

1.5 234

a) 230Vac

b) 120Vac

c) 100Vac

Output Current

Fig. 8-3 Efciency vs. input voltage at 12V,

4.5A, typ.

Fig. 8-4 Losses vs. input voltage at 12V, 4.5A,

typ.

Efciency

85 120 155 190 225 260Vac

Input Voltage

89%

Power Losses

12W

85 120 155 190 225 260Vac

Input Voltage

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

Rockwell Automation Publication 1606-RM015A-EN-P — March 2014 9

Bulletin 1606 Switched Mode Power Supplies

9. Functional Diagram

Fig. 9-1 Functional diagram

Input Fuse

Input Filter

Output Over-

Voltage

Protection

Input

Rectier

NTC

Inrush

Limiter

Power

Converter

Output

Voltage

Regulator

Output

Filter

OUT

10. Front Side and User Elements

Fig. 10-1 Front side

AOutput Terminals

Screw terminals,

Dual terminals for the negative and positive pole. Both poles are

equal

+ Positive output

-Negative (return) output

BInput Terminals

Screw terminals

L Phase (Line) input

N Neutral conductor input

PE (Protective Earth) input

CDC-on LED (green)

On, when the voltage on the output terminals is > 9V

DOutput voltage potentiometer

(single turn potentiometer)

Turn to set the output voltage. Factory set: 12.0V

All parameters are specified at 12V, 4.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless noted otherwise.

10 Rockwell Automation Publication 1606-RM015A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

11. Terminals and Wiring

All terminals are easy to access when mounted on the panel. Input and output terminals are separated from each

other (input below, output above) to help in error-free wiring.

Input Output

Type screw terminals screw terminals

Solid wire 0.5-6mm

0.5-6mm

Stranded wire 0.5-4mm

0.5-4mm

American Wire Gauge 20-10 AWG 20-10 AWG

Wire stripping length 7mm / 0.275inch 7mm / 0.275inch

Screwdriver 3.5mm slotted or

Pozidrive No 2

3.5mm slotted or

Pozidrive No 2

Recommended tightening torque 1Nm, 9lb.in 1Nm, 9lb.in

Instructions:

a) Use appropriate copper cables that are designed for an operating temperature of:

60°C for ambient up to 45°C and 75°C for ambient up to 60°C minimum.

b) Follow national installation codes and installation regulations!

c) Ensure that all strands of a stranded wire enter the terminal connection!

d) Up to two stranded wires with the same cross section are permitted in one connection point (except PE wire).

e) Do not use the unit without PE connection.

f) Screws of unused terminal compartments should be securely tightened.

g) Ferrules are allowed.

12. Lifetime Expectancy and MTBF

These units are extremely reliable and use only the highest quality materials. The number of critical components such

as electrolytic capacitors has been reduced.

AC 100V AC 120V AC 230V

Lifetime expectancy

34 000h 41 000h 56 000h at 12V, 4.5A and 40°C

180 000h *) 181 000h *) 128 000h *) at 12V, 2.25A and 40°C

95 000h *) 115 000h *) 158 000h *) at 12V, 4.5A and 25°C

MTBF

**)

SN 29500, IEC 61709 1 327 000h 1 458 000h 1 690 000h at 12V, 4.5A and 40°C

2 437 000h 2 639 000h 3 007 000h at 12V, 4.5A and 25°C

MTBF

**)

MIL HDBK 217F 1 085 000h 1 126 000h 1 067 000h at 12V, 4.5A and 40°C; Ground Benign GB40

1 464 000h 1 520 000h 1 445 000h at 12V, 4.5A and 25°C; Ground Benign GB25

*) The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime

expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specied in operational hours and is calculated according to the

capacitor’s manufacturer specication. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years

(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.

**) MTBF stands for Mean Time Between Failure, which is calculated according to statistical device failures, and indicates reliability of a

device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent the life of a product.

The MTBF gure is a statistical representation of the likelihood of a device to fail. A MTBF gure of e.g. 1 000 000h means that

statistically one unit will fail every 100 hours if 10 000 units are installed in the eld. However, it can not be determined if the failed unit

has been running for 50 000h or only for 100h.

Inhaltsverzeichnis

Andere Rockwell Automation Stromversorgung Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE240E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB90EH SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLERED20 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB60EH Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE192BDM Bedienungsanleitung

Rockwell Automation

Rockwell Automation A-B Quality 1606-XLS480G-3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480EP Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-DNENCAT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T823 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120F Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480ERZ Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS80E Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE240EP Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE260F Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLS960EE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB90EQ Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLB120E Bedienungsanleitung

Rockwell Automation

Rockwell Automation FactoryTalk Batch Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE240EDRZ SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE480EH Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLE120F Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLE96B-2 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung