Roland TrueVIS VG-640 Bedienungsanleitung
Thank you very much for purchasing this product.
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read
through this manual completely and store it in a safe location.
Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
The contents of this manual and the specications of this product are subject to change without notice.
This manual and the product have been prepared and tested as much as possible. If you nd any misprints or
errors, please inform Roland DG Corp.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur through use
of this product, regardless of any failure to perform on the part of this product.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur with respect
to any article made using this product.
R2-160322
Setup Guide
1
Company names and product names are trademarks or registered trademarks of their respective holders.
http://www.rolanddg.com/
Copyright © 2015-2016 Roland DG Corporation
Contents
Contents........................................................................................................1
1.Installation Environment.............................................................................2
Deciding On an Installation Site ................................................................................................. 2
Temperature and Humidity .......................................................................................................... 3
Installation Space ............................................................................................................................. 3
2.Included Items............................................................................................4
3.Assembly and Ink Filling ............................................................................5
Checks before Operations............................................................................................................. 5
Step 1: Assembling the Stand and Attaching the Printer.................................................. 6
Step 2: Installing the Media Holders........................................................................................10
Step 3: Installing the Drain Bottle.............................................................................................13
Step 4: Removing the Retainers................................................................................................14
Step 5:
Adjusting the Ink Tube and Axing a Label (Only When Using Four Colors)....
15
Step 6: Connecting the Cables ..................................................................................................16
Step 7: Initial Settings ...................................................................................................................17
Step 8: Ink Filling.............................................................................................................................19
4.Installing the Cutting Tool .........................................................................26
Step 1: Assembling the Cutting Tool .......................................................................................26
Step 2: Installing the Cutting Tool ............................................................................................27
5.Network Settings ......................................................................................29
Step 1: Make the Network Settings for the Computer......................................................29
Step 2: Make the Network Settings on the Printer.............................................................31
Step 3: Make the Port Settings for the Software RIP..........................................................34
This document is the setup guide for both the VG-640 and the VG-540. This document uses the following
notation to distinguish between the two models where necessary.
VG-640 — 64-inch model
VG-540 — 54-inch model
Also, most of the gures in this document depict the VG-640.
2
Deciding On an Installation Site
Install the machine in a quiet, stable location oering good operating conditions. An unsuitable location can
cause accidents, re, faulty operation, or breakdown.
WARNING Install the machine in a location that is level, stable, and able to bear the
weight of the machine.
The total weight of the machine may reach over 290 kg (639.3 lb.) for the 64-inch
model, 260 kg (573.1 lb.) for the 54-inch model. Installation in an unsuitable
location may cause a major accident, including tip over, fall, or collapse.
WARNING Never install this machine outside or in any location where exposure to
water or high humidity may occur.
Current leakage may cause electrical shock, electrocution, or combustion and
re.
WARNING Never install the machine close to any ammable object or in a gas-lled
location.
Combustion or explosion may occur.
WARNING Install the machine in a clean, brightly lit location.
Working in a location that is dark or cluttered may lead to an accident, such
as becoming caught in the machine as the result of an inadvertent stumble.
WARNING Position the machine so that the power plug is within immediate reach
at all times.
This is to enable quick disconnection of the power plug in the event of an emer-
gency. Install the machine next to an electrical outlet. Also, provide enough
empty space to allow immediate access to the electrical outlet.
CAUTION Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard or danger of com-
bustion due to ink fumes.
Unsuitable Installation Sites
Locations subject to large uctuations in temperature or humidity
Locations subject to shaking or vibration
Locations where the oor is tilted, not level, or unstable
Dusty locations
Locations exposed to direct sunlight
Locations near air-conditioning or heating equipment
Locations exposed to water or moving air
Locations exposed to considerable electrical or magnetic noise or other forms of electromagnetic
energy
1. Installation Environment
1. Installation Environment
3
Temperature and Humidity
Maintain the specied temperature and humidity even when the machine is not in use. Failure to do so may
result in malfunction.
Installation Space
The space shown in the gure is required in order to use this machine.
1,000 mm (39.4 in)
4,500 mm (177.2 in) (64-inch model)
4,000 mm (157.5 in) (54-inch model)
3,500 mm (137.8 in) (64-inch model)
3,000 mm (118.2 in) (54-inch model)
Unit space
Work space
2,000 mm (78.7 in)
During operation: Temperature 20 to 32°C (68 to 90°F), humidity: 35 to 80%RH (no condensation)
During non-operation: Temperature 5 to 40°C (41 to 104°F), humidity: 20 to 80%RH (no condensation)
4
The following items are included with the machine. Make sure they are all present before proceeding.
Power cord (1)
Arms
(1 each for right and left) Casters (2) Stand legs
(1 each for right and left)
Stand stay (1) Shafts (2)
Media holders/retaining
screws
(1 each for right and left)
Shaft clamps (2)
Middle pinch rollers * **
(The quantity varies de-
pending on the model.)
Media clamps*
(1 each for right and left)
Replacement wiper (1) Drain bottles (2) Tray pad (3) Hexagonal
wrench (1) Pipe (1)
TR cleaning liquid pouches
(2) Blade holder (1) Blade (1) Pin (1) Bolts (40) Washers
(22)
Replacement blades for
separating knife (1) Cable clamp (1) Tweezers (1) Cleaning
liquid (1)
Cleaning
sticks
Setup Guide (this docu-
ment) (1)
Read this rst (1)
User's Manual (1)
Inkjet printer mainte-
nance guide (1)
Cartridge-slot label (for
4 colors) (2) *** Software RIP (1)
* The media clamps and the middle pinch rollers are installed on the machine.
** (6) for the 64-inch model and (5) for the 54-inch model.
*** With the factory default settings, these labels are axed to the platen at the location where the front
cover opens.
2. Included Items
5
Checks before Operations
CAUTION Unloading and emplacement are operations that must be performed by
8 persons or more.
Tasks that require undue effort when performed by a small number of persons
may result in physical injury. Also, if dropped, such items may cause injury.
Completed Drawing
Necessary Tools
Hexagonal wrench
(large) Pipe*
* Use this when the hexagonal wrenches are too small to easily tighten bolts.
3. Assembly and Ink Filling
3. Assembly and Ink Filling
6
Step 1 : Assembling the Stand and Attaching the Printer
Procedure
A Place the caster on the stand leg.
Place the stand leg with the tabletop plate facing down, and then place the caster on top of the stand
leg. The casters have no particular front and rear orientation.
Tabletop plate
B Lightly tighten the bolts in the 4 upper locations and then in the 4 locations on the sides.
For the 4 upper locations, rst tighten the bolts in the narrow slots. In this way you can attach the caster
in the correct position.
Use washers in the 4 locations on the sides.
Tighten
temporarily
Bolts: 8
Washers: 4
NarrowWide
Tighten the
bolt here rst.
3. Assembly and Ink Filling
7
C Fully tighten the bolts in the 4 upper locations and then in the 4 locations on the sides.
Use the pipe when tightening the bolts in the upper locations. When tightening the bolts fully, tighten
them securely. Loose bolts may cause the stand to wobble.
Tighten fully
Bolts: 8
Washers: 4
Pipe
D
Assemble the opposing stand leg by following the same procedure from step Ato step C.
E Position the stand legs parallel to each other and separated by approximately 1,800 mm
(70.9 in.) for the 64-inch model or approximately 1,500 mm (59.1 in.) for the 54-inch model.
Position the legs so that the L-shaped brackets face the inside and the bent side of the tabletop plate
faces down for each leg.
About 1,800 mm (70.9 in.) (64-inch model)
About 1,500 mm (59.1 in.) (54-inch model)
Set this part on the bottom.
F Place the stand stay on the stand legs.
Place the stand stay so that its inside touches the L-shaped brackets and the stand legs in order to make
the 2 stand legs parallel.
Position the surface
with attachment holes
toward the casters.
3. Assembly and Ink Filling
8
G Lightly tighten the bolts in the order of 1, 2.
Use a washer for each bolt.
Tighten
temporarily
Bolts: 6
Washers: 6
H Fully tighten the bolts in the order of 1, 2.
Before tightening the bolts, check once more that the 2 stand legs are parallel. If the inside of the stand
stay is touching the L-shaped brackets and the stand legs, the stand legs will be parallel.
When tightening the bolts fully, tighten them securely. Loose bolts may cause the stand to wobble.
Tighten fully
Bolts: 6
Washers: 6
Andere Handbücher für TrueVIS VG-640
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Roland Drucker Handbücher
Roland
Roland VersaCamm VP-540i Bedienungsanleitung
Roland
Roland VersaCamm SP-300V Bedienungsanleitung
Roland
Roland SOLJET PROIII XC-540 Bedienungsanleitung
Roland
Roland PNC-1600 Bedienungsanleitung
Roland
Roland TrueVIS VF2-640 Bedienungsanleitung
Roland
Roland FLATJET FLJ-300 Bedienungsanleitung
Roland
Roland SolJet Pro II V SC-545EXW Bedienungsanleitung
Roland
Roland HB-12 Bedienungsanleitung
Roland
Roland FJ-42 Bedienungsanleitung
Roland
Roland VS-540 Bedienungsanleitung
Roland
Roland SP-540i Bedienungsanleitung
Roland
Roland Soljet EJ-640 Bedienungsanleitung
Roland
Roland Soljet Pro III XJ-640 Bedienungsanleitung
Roland
Roland LEC-300 Betriebsanleitung
Roland
Roland Soljet Pro III XJ-740 Bedienungsanleitung
Roland
Roland CX-500 Installations- und Betriebshandbuch
Roland
Roland SP-540i Bedienungsanleitung
Roland
Roland VersaEXPRESS RF-640 Bedienungs- und Wartungshandbuch
Roland
Roland Soljet Pro III XJ-540 Bedienungs- und Wartungshandbuch
Roland
Roland VS-640i Betriebsanleitung
