Ruijie XS-S1920 Series Installations- und Betriebsanleitung

Ruijie XS-S1920 Series Switches

Hardware Installation and Reference Guide V1.1

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption Statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the device.

This manual describes the functional and physical features and provides the device installation steps,

hardware troubleshooting, module technical specifications, and specifications and usage guidelines for

cables and connectors.

Audience

It is intended for the users who have some experience in installing and maintaining network hardware. At

the same time, it is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: [email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that

supported by the product, with configuration examples.

Command Reference

Describes the related configuration commands, including

command modes, parameter descriptions, usage guides, and

related examples.

Symbol Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the

device or cause data loss

Hardware Installation and Reference Guide

Product Overview

1Product Overview

The XS-S1920 series switch including the following models:

Table 1-1 XS-S1920

Model

10/100 Base-T

Auto-sensing Ethernet

Port

10/100/1000 Base-T

Auto-sensing

Ethernet Port

1000Base-X SFP

Port

Console

Port

XS-S1920-9GT1SFP-P-E

9 (Ports 1-8 support

PoE+/PoE）

XS-S1920-24T2GT2SFP-LP-E

24 ( Support PoE+/PoE）

XS-S1920-24T2GT2SFP-P-E

24 ( 1-24 ports Support

PoE+/PoE）

XS-S1920-26GT2SFP-LP-E

26 (1-24 ports support

PoE+/PoE）

XS-S1920-26GT2SFP-P-E

26 (1-24 ports support

PoE+/PoE）

The SPF ports are downward compatible with 100Base-FX. 100M optical modules should be used with 100Base-FX.

1000Base-T is compatible with 100Base-TX and 10Base-T in the downlink direction.

1.1 XS-S1920-9GT1SFP-P-E

Technical Specifications

Model

XS-S1920-9GT1SFP-P-E

CPU

Built-in CPU, single-core processor, 500MHz

Flash Memory

32MB

SDRAM

DDRIII 256MB

Optical Module

For details, see Appendix B.

The supported module type may change at any time. Consult us for the latest information.

SFP Port

Supports 1000Base-X and 100Base-FX modules.

Power Supply

AC input

Rated voltage range: 100V to 240V

Maximum voltage range: 90V to 264V

Frequency: 50/60 Hz

Rated current: 2A

Power cord requirement: 10A

EEE

Supported

PoE

Supports PoE and PoE+

Ports 1-8 are PoE/PoE+-capable with the maximum power output of 30W per port. Port 9 does

not support PoE or PoE+.

Hardware Installation and Reference Guide

Product Overview

The overall maximum output power of PoE/PoE+ is 125W.

PoE Mode

Mode A (data pairs 1-2 and 3-6)

Power

Consumption

Less than 11W with no PoE load

Less than 145W with PoE full load

Operating

Temperature

-5℃to 55℃(23°F to 131°F)

Storage

Temperature

-40℃to 70℃(-40°F to 158°F)

Operating Humidity

10% to 90% RH

Storage Humidity

5% to 95% RH

Fan

Not supported

Temperature

Warning

Not supported

Accessing Optical

Module Information

Not supported

EMC Standards

GB9254-2008

Security Standards

GB4943-2011

Earth Leakage

Current

≤1.5mA

Dimensions

(W x D x H)

300 mm x 220 mm x 43.6 mm

Weight

2 kg (with package)

The XS-S1920-9GT1SFP-P-E switch is a class A product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

The label indicates that you should not touch the device when it operates in environments of more than 50℃

(122ºF).

Product Appearance

On the front panel, the XS-S1920-9GT1SFP-P-E Ethernet switch provides nine 10/100/1000Base-T Ethernet ports, one

SFP port, and one Console port. On the back panel, it provides AC power ports.

Figure 1-1 Appearance of XS-S1920-9GT1SFP-P-E

Front Panel

Figure 1-2 Front Panel of XS-S1920-9GT1SFP-P-E

Hardware Installation and Reference Guide

Product Overview

Note:

1. System status LED

2. PoE status LED

3. Console port

4. PoE Mode Switch-Over Button

5. 10/100/1000Base-T auto-sensing Ethernet port

6. Copper port status LED

7. 10/100/1000Base-T auto-sensing Ethernet port

8. 1000Base-X SFP port

9. Copper port status LED

10. SFP port status LED

Back Panel

Figure 1-3 Back Panel of XS-S1920-9GT1SFP-P-E

Note:

1. Grounding pole

2. Hole for anti-theft lock

3. Power cord retention clip

4. AC power port

Heat Dissipation

The XS-S1920-9GT1SFP-P-E adopts natural heat dissipation, thereby ensuring normal function of the device in the

specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to allow

air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.

LEDs

LED

Panel Identification

State

Meaning

Off

The switch is not receiving power.

System status LED

Status

Blinking green

The system is being initialized.

Continuous blinking indicates errors.

Hardware Installation and Reference Guide

Product Overview

Solid green

The switch is operational.

Off

Indicates the switching state.

PoE status LED

PoE

Solid green

Indicates the PoE state.

Off

PoE is not enabled.

Solid green

PoE is enabled. The port is operational.

RJ45 port PoE status

LED

1-8

Blinking green

Indicates PoE overload.

Off

The port is not connected.

Solid green

The port is connected at 10/100/1000 Mbps.

1000Mbps RJ-45 port

status LED

1-9

Blinking green

The port is receiving or transmitting traffic at

10/100/1000 Mbps.

Off

The port is not connected.

Solid green

The port is connected at 100/1000 Mbps.

1000Mbps SFP port

status LED

10F

Blinking green

The port is receiving or transmitting traffic at

100/1000 Mbps.

1.2 XS-S1920-24T2GT2SFP-LP-E

Technical Specifications

Model

XS-S1920-24T2GT2SFP-LP-E

CPU

Built-in CPU, single-core processor, 500MHz

Flash Memory

32MB

SDRAM

DDRIII 256MB

Optical Module

For details, see Appendix B.

The supported module type may change at any time. Consult us for the latest information.

SFP Port

Supports 1000Base-X and 100Base-FX modules.

Power Supply

AC input

Rated voltage range: 100V to 240V

Maximum voltage range: 90V to 264V

Frequency: 50/60 Hz

Hardware Installation and Reference Guide

Product Overview

Rated current: 4A

Power cord requirement: 10A

EEE

Supported

PoE

Supports PoE and PoE+

Ports 1-24 are PoE/PoE+-capable with the maximum power output of 30W per port. Up to 12

ports can provide power to powered devices at the same time.

Ports 25 and 26 do not support PoE or PoE+.

The overall maximum output power of PoE/PoE+ is 185W.

PoE Mode

Mode B (data pairs 4-5 and 7-8)

Power

Consumption

Less than 15W with no PoE load

Less than 215W with PoE full load

Operating

Temperature

-5℃to 55℃(23°F to 131°F)

Storage

Temperature

-40℃to 70℃(-40°F to 158°F)

Operating Humidity

10% to 90% RH

Storage Humidity

5% to 95% RH

Fan

Speed adjustment

Temperature

Warning

Not supported

Accessing Optical

Module Information

Not supported

EMC Standards

GB9254-2008

Security Standards

GB4943-2011

Earth Leakage

Current

≤1.5mA

Dimensions

(W x D x H)

440 mm x 292 mm x 43.6 mm

Weight

4.2 kg (with package)

The XS-S1920-24T2GT2SFP-LP-E switch is a class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate measures.

Product Appearance

On the front panel, the XS-S1920-24T2GT2SFP-LP-E Ethernet switch provides twenty-four 10/100Baes-T Ethernet ports,

two 10/100/1000Base-T Ethernet ports, two 1000M SFP port, and one Console port. On the back panel, it provides AC

power ports.

Figure 1-4 Appearance of XS-S1920-24T2GT2SFP-LP-E

Hardware Installation and Reference Guide

Product Overview

Front Panel

Figure 1-5 Front Panel of XS-S1920-24T2GT2SFP-LP-E

Note:

1. System status LED

2. PoE status LED

3. Console port

4. PoE Mode Switch-Over Button

5. 10/100Base-T auto-sensing Ethernet port

6. Copper port status LED

7. Copper port status LED

8. 10/100/1000Base-T auto-sensing Ethernet port

9. SFP port status LED

10. 1000Base-X SFP port

Back Panel

Figure 1-6 Back Panel of XS-S1920-24T2GT2SFP-LP-E

Note:

1. Grounding pole

2. Vent

3. Power cord retention clip

4. AC power port

Heat Dissipation

The XS-S1920-24T2GT2SFP-LP-E adopts turbine fans for heat dissipation, thereby ensuring normal function of the

device in the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the

cabinet to allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking

vents. Figure 1-7 shows the flow scheme of heat dissipation.

Figure 1-7 Flow Scheme of Heat Dissipation

Hardware Installation and Reference Guide

Product Overview

LEDs

LED

Panel Identification

State

Meaning

Off

The switch is not receiving power.

Blinking green

The system is being initialized.

Continuous blinking indicates errors.

System status LED

Status

Solid green

The switch is operational.

Off

Indicates the switching state.

PoE status LED

PoE

Solid green

Indicates the PoE state.

Off

PoE is not enabled.

Solid green

PoE is enabled. The port is operational.

RJ45 port PoE status

LED

1-24

Blinking green

Indicates PoE overload.

Off

The port is not connected.

100Mbps RJ-45 port

status LED

1-24

Solid green

The port is connected at 10/100 Mbps.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ruijie Schalten Handbücher

Ruijie

Ruijie RG-S6220-48XS6QXS-H Installations- und Betriebsanleitung

Ruijie

Ruijie RG-EG210G-P Bedienungsanleitung

Ruijie

Ruijie RG-S6920-4C Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2900G-E Series Bedienungsanleitung

Ruijie

Ruijie RG-CS86-20XS Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NIS3100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-IS2712G Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-ES Series Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NIS3100 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES200 Series Bedienungsanleitung

Ruijie

Ruijie RG-ES08 Bedienungsanleitung

Ruijie

Ruijie RG-NBS3200 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6910-3C Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SF2920U Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6580-48CQ8QC Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S5300-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-ES106D-P Installations- und Betriebsanleitung

Ruijie

Ruijie RG-CS83 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES05 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6000C-48GT4XS-E Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S8600 Series Bedienungsanleitung

Ruijie

Ruijie RG-S7600 Series Installations- und Betriebsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

Vimar

Vimar 6592 Montageanleitung