Samson AirLine Bedienungsanleitung

UHF Wireless System

Owners Manual

Handheld Transmitter

Presentation

Transmitter

• AX1 Handheld Transmitter

• AL1 Presentation Transmitter

• AR1 Receiver

• UR1 Receiver

• UM1 Receiver

SAMSON

ENGLISH

Introduction 1

QuickStart 2

Guided Tour - AR1 Receiver 4

Guided Tour - UR1 Receiver 6

Guided Tour - UM1 Receiver 9

Guided Tour - AX1 Handheld Transmitter 12

Guided Tour - AL1 Presentation Transmitter 14

Setting Up and Using Your AirLine System 17

Specifications 81

Appendix A: Channel Plan 85

Appendix B: Attaching The Lanyard to the AL1 86

FRANCAIS

Introduction 21

Prise en main 22

Visite guidée – Récepteur AR1 24

Visite guidée – Récepteur UR1 26

Visite guidée – Récepteur UM1 29

Visite guidée – Emetteur main AX1 32

Visite guidée – Emetteur de presentation AL1 34

Configuration et utilisation des systèmes AirLine 37

Spécifications 81

Appendix A: Tableau de conversion de fréquence 85

Appendix B: Attaching The Lanyard to the AL1 86 Samson Technologies Corp.

575 Underhill Blvd.

P.O. Box 9031

Syosset, NY 11791-9031

Phone: 1-800-3-SAMSON (1-800-372-6766)

Fax: 516-364-3888

Table of Contents

Produced by On The Right Wavelength for Samson Technologies Corp.

Printed August 2000

DEUTSCHE

Einleitung 41

Schneller Einstieg 42

Übersicht - Empfänger AR1 44

Übersicht - Empfänger UR1 46

Übersicht - Empfänger UM1 49

Übersicht - Hand-Sender AX1 52

Übersicht - Presentation-Sender AL1 54

Konfiguration und Betrieb der AirLine-Systeme 57

Technische Daten 81

Anhang A: Frequenzzuordnung der Empfangskanäle 85

Anhang B: Attaching The Lanyard to the AL1 86

ESPANOL

Introducción 61

Arranque rápido 62

Recorrido guiado –Receptor AR1 64

Recorrido guiado –Receptor UR1 66

Recorrido guiado –Receptor UM1 69

Recorrido guiado –Transmisor manual AX1 72

Recorrido guiado –Transmisor de presentation AL1 74

Ajuste y uso de su sistema AirLine 77

Especificaciones 81

Apéndice A: Tabla de conversión de frecuencias 85

Apéndice B: Attaching The Lanyard to the AL1 86

Welcome to Samson AirLine—the wireless system for the new millenium! Wireless microphone and instrument systems were

originally developed to eliminate cables, providing unparalleled freedom of movement. AirLine takes this concept to a new level with

transmitters so small, lightweight and aerodynamic, they are nearly invisible, providing a completely “hassle-free” user experience.

To create the world’s smallest wireless transmitters, we developed new proprietary technology. Featuring miniaturized circuitry and the

ability to operate on a single tiny AAA battery (with 14 hours typical battery life), these transmitters also feature significantly improved

wireless reception and sound quality. What’s more, the AR1 micro receiver developed especially for the AirLine system is actually

smaller than the typical wireless transmitter.

There are two different Samson AirLine systems detailed in this manual. Both operate in the 801 - 805 MHz UHF frequency range

and each contains an AR1 micro receiver or one of the receivers from our acclaimed Series One system—either a UR1 true diversity

receiver (for professional performance applications) or a UM1 micro diversity receiver (optimized for the production of professional

audio tracks to accompany your video shoot or live broadcast). The AirLine UHF Microphone System contains an AX1 hand-held

transmitter, which plugs into any standard wired dynamic microphone. The AirLine UHF Presentation System contains an AL1 pre-

sentation transmitter, which contains a built-in electret condenser microphone and connection for an optional lavalier microphone.

In this manual, you’ll find a more detailed description of the features of all AirLine systems, as well as a guided tour through all

components, step-by-step instructions for setting up your system and full specifications. If your AirLine system was purchased in the

United States, you’ll also find a warranty card enclosed—don’t forget to fill it out and mail it! This will enable you to receive online

technical support and will allow us to send you updated information about this and other Samson products in the future. If your

AirLine system was purchased outside of the U. S., contact your local distributor for warranty details. Also, be sure to check out our

website (http://www.samsontech.com) for complete information about our full product line.

SPECIAL NOTE for U.S. purchasers: Should your AirLine system ever require servicing, a Return Authorization number (RA) is

necessary. Without this number, the unit will not be accepted. If your AirLine system was purchased in the United States, please call

Samson at 1-800-372-6766 for a Return Authorization number prior to shipping your system. If possible, return the unit in its original

carton and packing materials. If your AirLine system was purchased outside of the U. S., contact your local distributor for information.

Samson AirLine

Introduction

ENGLISH

If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your

AirLine system in a matter of minutes! Detailed instructions for setting up and using your AirLine system can be found on page 17 of

this manual, and the “Guided Tour”sections on pages 4 - 16 provide full descriptions of all AirLine component controls and displays.

1. Make sure that the supplied receiver and AX1 or AL1 transmitter are factory preset to the same channel.

2. Physically place the receiver where it will be used (if desired, the AR1 receiver model can be wall-mounted using the supplied

holder) and extend its antenna(s) vertically.

3. Set the power switch to your transmitter to the “off”position (away from the arrow) and place a fresh battery in it. Then turn the

transmitter back on momentarily; its LED will flash once and then go off if the battery is sufficiently strong. Once battery strength is

verified, turn the transmitter off.

4. If you are using an AX1, plug its XLR connector into a wired dynamic microphone; make a good tight connection, using the

supplied rubber gasket if necessary. If you are using the AL1 with an external lavalier microphone, make the physical connection

between its input connector and the microphone.

5. Turn your audio system off and make the physical cable connection between the receiver’s balanced or unbalanced output jack

(if necessary, both can be used simultaneously) and a mic level audio input of your amplifier or mixer. If your system contains a UR1

or UM1 receiver, be sure to set its Audio Output Level switch correctly.

6. Turn the Volume, Level or AF Level knob on the receiver completely counterclockwise. Connect the supplied AC adapter to the

receiver and plug it in (or place a fresh battery in the UM1 receiver), but leave its power off for the moment.

7. Turn on the receiver. If your system contains an AR1 or UR1 receiver, its “Power”LED will light steadily red. (Note: the UM1

Samson AirLine QuickStart

ENGLISH

receiver has no such LED.)

8. Turn on your transmitter. If your system contains an AR1 receiver, its “Power/ RF”LED should change color from red to green, indi-

cating that it is receiving valid RF signal and is placed and positioned correctly. If your system contains either a UR1 or UM1 receiver,

one of the “A/B Receiver”LEDs will be lit, showing you whether the (left) “A”or (right) “B”receiver is currently being used. The UR1 /

UM1 meter will also indicate the strength of the incoming RF signal.

9. Turn on your connected amplifier and/or mixer but keep its volume all the way down. If your system contains an AL1 transmitter,

make sure it is unmuted. Set the Volume, Level or AF Level knob on the receiver fully clockwise; this is unity gain.

10. Speak or sing into your mic at a normal performance level while slowly raising the audio input control of your amplifier or mixer

until the desired level is reached. If necessary, use the supplied plastic screwdriver to adjust the transmitter’s Gain trimpot in order to

increase or decrease its signal level. If you are using an AL1 transmitter with the built-in microphone, correct placement is critical to

sound quality. It should be unobstructed by clothing and either clipped to a shirt pocket or lapel, or worn around the neck on the sup-

plied lanyard.

11. Do a walkaround through the intended area of coverage while observing the receiver’s “Power/RF”LED or RF Meter; it should

indicate sufficient RF reception in all areas of coverage (in the case of the AR1, the LED will light steadily green) . Reposition it (or its

antenna) as necessary. If extended range coverage is required, a Samson UR1 or UM1 true diversity receiver (set to the same channel

as the transmitter) should be used

12. If you hear any spurious noise from the receiver output when the transmitter is turned off, use the supplied plastic screwdriver to

adjust the receiver Mute (squelch) level control, slowly turning it clockwise to the point at which the noise disappears.

Samson AirLine

QuickStart

ENGLISH

1: Antenna - This swivel mounting allows full rotation for

optimum placement of the antenna. In normal operation,

the antenna should be placed in a vertical position. It can

be folded inward for convenience when transporting the

AR1. See the “Setting Up and Using Your AirLine System”

section on page 17 in this manual for more information

about antenna positioning.

2: Power On / RF LED - This lights red whenever the AR1 is

powered on and green whenever the AR1 is receiving RF

signal from a transmitter.

3: Peak LED - This LED lights red when output signal from

the AR1 is at the onset of clipping (that is, when it is on the

verge of being distorted). If you see this light during

operation, move the microphone further away or lower the

volume level of your instrument or transmitter. For more

information, see the section entitled “Setting Up and Using

Your AirLine System”on page 17 in this manual.

4: Power switch - Move this switch in the direction of the

arrow to turn power to the AR1 on; move it away from the

arrow to turn power off.

5: Volume control - This knob sets the level of the audio

signal being output through both the AR1 balanced and

unbalanced output jacks (see #6 and #7 on the following

page). Reference level is obtained when the knob is turned

fully clockwise.

Samson AirLine Guided Tour - AR1 Receiver

ENGLISH

6: Unbalanced output* - Use this unbalanced high impedance

(5 - 10 K Ohm) 1/4" jack when connecting the AR1 to consumer

(-10) audio equipment. Wiring is as follows: tip hot, sleeve ground.

7: Balanced output* - Use this electronically balanced low

impedance (600 - 2500 Ohm) XLR jack when connecting the AR1

to professional (+4) audio equipment. Pin wiring is as follows:

Pin 1 ground, Pin 2 high (hot), and Pin 3 low (cold).

8: Mute (squelch) control -

This control determines the

maximum range of the AR1

before audio signal dropout.

Although it can be adjusted

using the supplied plastic

screwdriver, it should

normally be left at its factory setting. See the “Setting Up and UsingYour AirLine System”

section on page 17 in this manual for more information.

9: DC input - Connect the supplied 12 volt 200 mA power adapter here.

WARNING: Do not substitute any other kind of power adapter; doing so can cause

severe damage to the AR1 and will void your warranty.

As shown in the illustration on the left, the supplied AR1 receiver holder can be used to

wall-mount the AR1 in fixed installations.

* If required, both the balanced and unbalanced outputs can be used simultaneously.

Samson AirLine

Guided Tour - AR1 Receiver

Wall-mount AR1 receiver holder

ENGLISH

1: Antennas (A and B) - The

antenna mountings allow full

rotation for optimum placement.

In normal operation, both Antenna

A (the antenna on the left) and

Antenna B (the antenna on the

right) should be placed in a vertical

position. Both antennas can be

folded inward for convenience

when transporting the UR1. See

the “Setting Up and Using the

AirLine System”section on page

17 in this manual for information

about antenna installation and

positioning.

2: AF (Audio Frequency) Level control - This knob sets the level of the audio signal being output through both the balanced and

unbalanced output jacks on the rear panel (see #2 and #4 on page 8 in this manual). Reference level is obtained when the knob is

turned fully clockwise (to its “10”setting).

3: Peak LED - This LED lights yellow when output signal from the UR1 is at the onset of clipping (that is, when it is on the verge of

being distorted). If you see this light during operation, move the microphone further away or lower the output level of your

instrument or transmitter. For more information, see the section entitled “Setting Up and Using the AirLine System”on page 17 in

this manual.

Samson AirLine Guided Tour - UR1 Receiver / Front Panel

ENGLISH

SAMSON

UHF RECEIVER

351

446

4: A/B Receiver LEDs - When signal is being received, one of these will be lit green, showing you whether the (left) “A”or (right) “B”

receiver is currently being used. The UR1 constantly scans its two antennas and automatically selects whichever is receiving the

strongest, clearest signal. This True Diversity switching is completely inaudible, but it effectively increases overall range while vir-

tually eliminating potential interference and phase cancellation problems.

5: RF (Radio Frequency) Level meter - This five-segment meter (similar to theVU bar meter used on audio devices) indicates the

strength of the UHF signal being received. When all segments are lit, the incoming RF signal is at optimum strength; when only the

left-most segment is lit, the incoming RF signal is at minimum strength. If no segments are lit, no signal is being received; check to

ensure that the transmitter is on and that it is set to the same channel as the UR1. See the “Setting Up and Using the AirLine System”

section on page 17 in this manual for more information.

6: Power LED - This lights red whenever the UR1 is turned on.

7: Mute (squelch) control - This control determines the maximum range of the UR1 before audio signal dropout. Although it can be

adjusted using the supplied plastic screwdriver, it should normally be left at its factory setting. See the “Setting Up and Using the

AirLine System”section on page 17 in this manual for more information.

8: Power switch - Use this to turn the UR1 power on and off. When the receiver is on, the Power LED (see #6 above) is lit.

Samson AirLine

Guided Tour - UR1 Receiver / Front Panel

ENGLISH

1: DC input - Connect the supplied

12 volt 160 mA power adapter here,

using the strain relief as shown in the

illustration below. WARNING: Do not

substitute any other kind of power

adapter; doing so can cause severe

damage to the UR1 and will void your

warranty.

2: Unbalanced output* - Use this

unbalanced high impedance (5K

Ohm) 1/4" jack when connecting the

UR1 to consumer (-10) audio

equipment. Wiring is as follows:

tip hot, sleeve ground.

3: Audio Output Level switch - Sets

the audio output level attenuation of

the balanced output (see #4 below) to

-20 dBm (line level) or -40 dBm

(mic level). See “Setting Up and

Using the AirLine System”on page 17.

4: Balanced output* - Use this electronically balanced low impedance (600 Ohm) XLR jack when connecting the UR1 to professional

(+4) audio equipment. Pin wiring is as follows: Pin 1 ground, Pin 2 high (hot), and Pin 3 low (cold).

* If required, both the unbalanced and balanced outputs can be used simultaneously.

Samson AirLine Guided Tour - UR1 Receiver / Rear Panel

ENGLISH

UNBALANCED

OUTPUT BALANCED SWITCH BALANCED OUTPUT

XLR:

1 GND

2 HOT

3 COLD

LINE:

-20dBm600Ω

MIC:

-40dBm600Ω

MIC LINE

POWER RATING

DC 12V, 1.9W(160mA)

-10dB 5KΩ

DC INPUT

1234

AC CABLE LOCK

CAUTION:

USE SAMSON

AC ADAPTOR

ONLY

CABLE LOCK: LOOP THRU AND TIE

Using the strain relief: Gather up a loop of wire and pass it through the strain relief,

then pass the adapter plug through the loop in order to create a knot.

Andere Handbücher für AirLine

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Samson Mikrofonsystem Handbücher

Samson

Samson AIRLINE CR77 Bedienungsanleitung

Samson

Samson STAGE 412 Bedienungsanleitung

Samson

Samson Stage 212 Bedienungsanleitung

Samson

Samson Concert 288x Bedienungsanleitung

Samson

Samson EXPEDITION XP40iw Bedienungsanleitung

Samson

Samson UHF Synth 32 Bedienungsanleitung

Samson

Samson AirLine Bedienungsanleitung

Samson

Samson AIRLINE CR77 Bedienungsanleitung

Samson

Samson Concert 88 Bedienungsanleitung

Samson

Samson DK705 Bedienungsanleitung

Samson

Samson AIRLINE CR77 Bedienungsanleitung

Samson

Samson Concert UHF Bedienungsanleitung

Samson

Samson VHF Micro VHF Micro TRUE DIVERSITY WIRELESS Bedienungsanleitung

Samson

Samson CB88 Bedienungsanleitung

Samson

Samson WSM Wireless System Manager for Windows 95 Bedienungsanleitung

Samson

Samson Airline 88 Bedienungsanleitung

Samson

Samson SYNTH32 Bedienungsanleitung

Samson

Samson STAGE 5H Bedienungsanleitung

Samson

Samson CONCERT 88X Bedienungsanleitung

Samson

Samson S-Combine Bedienungsanleitung

Samson

Samson AirLine 77 AH1N Bedienungsanleitung

Samson

Samson Concert 77 Bedienungsanleitung

Samson

Samson AirLine 88 Series Bedienungsanleitung

Samson

Samson Stage 266: Dual Handheld Wireless System Bedienungsanleitung

Beliebte Mikrofonsystem Handbücher anderer Marken

Paso

Paso R824 Bedienungsanleitung

Naxa

Naxa NAM-982 Bedienungsanleitung

Motorola

Motorola PMNN4461 Bedienungsanleitung

Xvive

Xvive U3 Bedienungsanleitung

Tekon

Tekon DUOS Bedienungsanleitung

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Bedienungsanleitung

Devine

Devine WMD-IE Bedienungsanleitung

LG LF-D7150 Bedienungsanleitung

GE S768DAV Bedienungsanleitung

LD U305 HBH 2 Bedienungsanleitung

Chainway

Chainway URA8 Bedienungsanleitung

ORATOR

ORATOR D860TD Bedienungsanleitung

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Bedienungsanleitung

Alpha Technologies

Alpha Technologies RBMS Bedienungsanleitung

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Bedienungsanleitung

Shure

Shure UA844 Bedienungsanleitung

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Bedienungsanleitung

Pyle

Pyle PDWM5000 Bedienungsanleitung