Samsung SU2931 Bedienungsanleitung

Vacuum

Cleaner

SU-2930 Series

FOR HOUSEHOLD USE ONLY

Operating

Instructions

IMPORTANT SAFETY INSTRUCTIONS ......................... 1

ASSEMBLING PARTS ..................................................... 2

OPERATION .................................................................... 3

MAINTENANCE ............................................................... 5

TROUBLESHOOTING ..................................................... 8

Read these instructions before operating the vacuum cleaner

•The design and specification may be different depending on the models.

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지1 i n

IMPORTANT SAFETY INSTRUCTIONS

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical

appliance, basic precautions should always be followed, including the following:

PLEASE READ ALL INSTRUCTIONS

BEFORE USING THIS VACUUM CLEANER.

WARNING: To reduce the risk of fire, electric shock, or injury:

• Do not leave vacuum cleaner unattended when it is plugged in.

• Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• The appliance is not intended for use by young children or infirm persons without supervision.

• Young children should be supervised to ensure that they do not play with the appliance.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug.

• If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors or

dropped in water, take it to a service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull the cord

around sharp edges or corners. Keep cord away from heated surface.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not handle vacuum cleaner or plug with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep openings free

of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• Do not use without dirt cup or filters in place. Empty cup and clean filter frequently when

picking up very fine materials such as powder.

• Turn off all controls before unplugging vacuum cleaner.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible materials such as gasoline or fine wood

standings or use in areas where they may be present.

• Store your vacuum cleaner indoors in a cool, dry area.

• Avoid picking up hard, sharp objects with the cleaner, they may damage the cleaner.

• Always turn off this appliance before connecting or disconnecting the hose, removing the

bottom plate for maintenance.

• Use only on dry, indoor surfaces, never change the plug in any way.

• Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

• Do not touch the brush roller when it is rotating.

• Keep suction away from your face when using nozzles and pipe.

• Do not pull the power cord around sharp corners and do not allow it to become trapped.

• Unplug before connecting turbine nozzle.(only using turbine-brush model)

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지2 i n

Assembling Parts

Identifications of parts

The assembled cleaner will look

like the illustration to the left.

1. Handle

2. Power switch

3. Quick release cord hook

4. Post-Motor Filter

5. Crevice tool

6. Handle release

7. Carrying handle

8. Hose

9. Extension wand

10. Combination tool

11. Cyclone-Lever

12. Dirt Cup

13. Filter Cup

14. Upper Tank

15. Louvers

16. Hose Wand Base

17. Height Adjustment Dial

18. Hose Clip

19. Mini Turbo Brush

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

Step 1. Attaching the Handle

Stand the vacuum

upright and slide the

base of the handle

firmly into the grooves

at the top of the

vacuum body.

Insert the screw provided

into the existing hole.

Tighten the screw securely

with a screwdriver.

Before securing the handle,

please check that the

handle is fitted to the

vacuum body and make

sure there’s no gap.

1-1

1-2 1-3

Step 2. Attaching the Hose and Tools

Slide the extension

wand and the crevice

tool together into the

storage clip.

Attach the Mini Turbo

Brush by putting the

rib at the bottom of

Mini Turbo Brush on

two hooks of Handle.

Snap Mini Turbo

Brush into place as

shown.

1-6 1-7

Line up the tabs on the

base of the Twist Snap

Hose with the

corresponding notches

on the hose collar as

shown.

Slide the end of the

hose wand with tabs

into the Hose Wand

Base.

1-4 1-5

Front Back

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지3 i n

Operation

A. Combination tool:

Two types of cleaning tools are included in

one attachment: rotate for desired tool.

·Use brush side to dust furniture,

blinds, books, lamps, shelves.

·Use upholstery side for curtains,

draperies, cushions, fabrics.

B. Crevice tool:

Use in corners, on stairs, baseboards, and

behind furniture.

C. Extension Wand:

Use with desired attachments and narrow

wand for a longer reach.

D. Mini Turbo Brush :

Use rotating brush action for small areas

such as stairs and upholstery.

Note: Press gently when using Mini Turbo

Brush to gain maximum cleaning. Too much

pressure could cause the brush to stop rotating.

󳢬󳢬option

E. Wooden Floor Brush (Select Models):

Use for bare floors. Swivel head turns to

get into tight spaces and fits under cabinets.

Note: The Wooden Floor Brush does not

store on board.

2-1 2-2 2-3

Carrying handle

The cleaner can also be moved by

using the carrying handle.

2-4 2-5

ON-OFF Switch

1.To turn cleaner on, press the

Power switch.

2.To the cleaner off, press the

Power switch again.

Handle positions

The handle of your cleaner has

three positions; upright for storage

and when using cleaning tools;

operating for general operation on

carpet and floors; low for reaching

under low furniture. Step on handle

release pedal to lower handle.

Transporting cleaner

To move your cleaner from room to

room, put the handle in upright

position, tilt the cleaner back on its

rear wheels and push forward.

󳢬󳢬option

Cleaning Tool attachments

Attachment tools can be used

to clean furniture or drapes, on

stairs or in corners.

When using the attachments,

ensure the vacuum cleaner is

placed firmly on the floor with the

handle in the upright position. Do

not place the vacuum on top of

furniture or steps as the brushroller

may cause damage.

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지4 i n

Carpet height

adjustment

Carpet and rug cleaning takes

place at the nozzle (A).

When it is necessary to raise

and lower the nozzle for

various carpet pile heights,

rotate the nozzle control dial

(B) to the desired setting.

For maximum cleaning

performance, The following

carpet height settings are

recommended:

·Lowest setting: for bare

floors

·Medium setting : for short

and medium pile carpets

·Higher settings: for very

deep pile carpet where

easier pushing effort is

desired, while maintaining

good cleaning performance.

Note: If the cleaner is difficult

to push, rotate knob to the

next higher setting.

2-7 2-8

Cleaning lightweight

flexible rugs

Stand on one end of rug and move

cleaner toward other end or edge.

Before reaching edge, push down on

handle. This will lift up the nozzle(front of

cleaner)and will prevent rug from clinging

to cleaner.

Continue to lift front of cleaner so that

when you have reached the edge, it is

completely off the rug. Move cleaner

back to start again, lower front of cleaner,

and use only forward strokes.

2-6

Operation

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지5 i n

Maintenance

Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will

ensure continued cleaning effectiveness.

When to empty the Dirt Cup

The dirt cup needs to be emptied when the dirt reaches the "Full" line on the side of the Cup.

If more dirt than this accumulates, your cleaner will not operate effectively.

Note: All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming.

Emptying the Dirt Cup

Disconnect cleaner from electrical outlet.

Slide the Cyclone-Lever to the

"Unlock" position.

Grasp handle and pull the Dirt

Cup straight out to remove from

Vacuum.

Empty dirt into garbage container.

Put the Dirt Cup back in the

vacuum and slide the lever to the

"Lock" position.

Cleaning The Circular

Filters.

Grasp the Filter Cup located at

the bottom of the Dirt Cup and twist

counterclockwise to unlock and

remove.

3-2 3-3

Cleaning the Pre/Post-motor Filter

How to clean

Disconnect cleaner from

electrical outlet.

The Pre-Motor Filter protects the

Motor from debris.

It is located underneath the Dirt

Cup and Filter Cup in the

Center of the round part of the

Cyclone-Lever.

Remove the small round Filter

and any debris on top of it.

Rinse

well under warm water, then air

dry thoroughly before replacing.

The Post-Motor Filter assists in

the filtration process to return

clean air to the room. It is

located behind the door on the

front of the Cleaner.

When the filter becomes dirty,

The Hepa-Filter :

Open the door, remove the filter

and replace.

The Hepa-Filter is not

washable and must be

replaced.

Replace the door by inserting

the tabs on the left side and

snapping the right side into

place.

3-5 3-6

Grasp the Circular Filters and twist

to unlock.

Pull straight up to remove.

Separate the Outer foam and

Inner pleated Circular Filters.

Wash each individually by hand

in warm water. Mild detergent

may be used if desired.

Rinse well, then air dry

Thoroughly dry before putting

them back together and

replacing in the Filter Cup The

Filter Cup may be washed In

warm water with a mild

detergent. Make sure it is

completely dry before

reassembling with fliters.

Do not operate cleaner without

Either the Pre-Motor Filter or

Post-Motor Filter in place.

Hepa-Filter

3-4

Pre-Motor

Filter

3-1

Unlock

Position

Lock

Position

Full Line

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지6 i n

Maintenance

The belt

The belt on your cleaner causes the

agitator to rotate and is important for

the effective operation of the

cleaner. The belt is located under

the bottom plate of the cleaner and

should be checked from time to time

to be sure it is in good condition.

When to replace

Disconnect cleaner from

electrical outlet.

To check belt, remove bottom plate

as shown in “How to replace.”

Replace belt if it is stretched, cut or

broken.

Remove agitator and used belt.

Discard used belt.

3-7 3-8

Insert agitator through belt and place

belt in belt guide (C) on agitator.

Should the agitator shield (D)

become dislodged while replacing

the belt or the agitator, reposition it

as shown, noting the placement of its

belt guide (E)

When to replace the

agitator brush roll

When agitator brushes are worn, the

agitator should be replaced.

To check condition of brushes,

disconnect cleaner from electrical

outlet.

Move the edge of a card across

bottom plate while turning agitator.

To maintain cleaning effectiveness,

replace agitator if brushes do not

touch card.

Grasp agitator firmly and fit it into

position by first sliding the end opposite

the belt into the rectangular slot (F) on

side of cleaner.

Pull other side of agitator (G) into place.

Turn agitator, making sure belt is not

pinched between agitator and agitator

shield.

3-10

With lettering on outside of belt and

positioned as shown in box on (D),

slide new belt over motor pulley (B).

3-9

3-11

How to replace

Disconnect cleaner from electrical

outlet.

Remove bottom plate, belt and

agitator following directions in “The

belt” section beginning with Fig. 3-10.

Discard old agitator.

Continue following the directions in

“The belt” section to reposition belt,

new agitator and bottom plate.

Reposition bottom plate and 4

screws. Tighten screws securely.

3-12 3-13

How to replace

Disconnect cleaner from electrical

outlet.

Place handle in low position and turn

cleaner over so bottom side is up.

Remove the 4 screws as shown with

a screw driver.

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지7 i n

Maintenance

Clearing Blockages

Disconnect cleaner from electrical outlet.

The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can

sometimes become clogged. If you notice a change in the sound of the vacuum motor, check for blockages.

Remove the Hose and

disconnect the Wand.

Check for clogs in the vacuum

base, the wand, the hose and

the suction inlet.

If the blockage persists, turn

the vacuum cleaner off and

unplug it. Remove the bottom

plate. Lift up the short hose in

the base of the vacuum.

Inspect the hose for clogs and

remove any obstructions.

Replace the short nozzle hose

and the bottom plate.

Remove Dirt Cup and check

Upper Tank and Louvers.

Check to make sure Louvers

are Installed correctly. To

unlock the Louvers, grasp the

rim and turn Toward the left.

Pull straight down to remove. If

the Louvers are missing or not

locked into place, check and

clear the tube in the center of

the Dirt Cup.

Brush bar Replacement

Remove the tool from the hose,

and turn upside down. Slide the

switch to unlock position.

Remove bottom plate.

And remove brushbar and

discard.

Inspect belt to ensure that it is in

good condition. If broken or

cracked, please replace. (See

below for details.)

With the curved ends facing

down, slide end plates of

brushbar into slots on the tool.

To replace bottom plate, insert

the four tabs on edge of

bottom plate into slots on front

of tool. Pivot bottom plate

down and snap closed.

3-14 3-16

3-15

Use for upholstered furniture, carpeted stairs and hard-to-reach places.

3-17 3-18 3-19

Mini Turbo Brush

3-20 3-21 3-22

Belt Replacement

Grasp turbine and pull firmly to

remove.

Remove belt from turbine pulley.

Replace with new belt.

With flat sides of turbine

retainers pointing down, slide

retainers into grooves in tool

housing and snap into place.

Replace brushbar and bottom

plate.

Cleaning Brushbar

• Cut off pet hairs or threads

surrounding brush by using

scissors.

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지8 i n

Troubleshooting

Check this list of possible problems and solutions before bringing your vacuum to a service center.

Problem: Cleaner won’t run

Possible Cause

Possible Solution

··Not firmly plugged in

··Plug unit in firmly

··No voltage in wall plug

··Check fuse or breaker

··Blown fuse or tripped breaker

··Replace fuse or reset breaker

··Filters blocked or dirty

··Clean filters as per manual instructions

Problem : Poor job of dirt pickup

Possible Cause

Possible Solution

··Full or clogged Dirt Cup

··Empty the Dirt Cup and check for blockages.

··Broken or worn belt

··Replace belt.

··Clogged hose or nozzle

··Clean hose or nozzle area.

··Hole in hose

··Replace hose.

··Dirt Cup improperly installed

··Properly install the Dirt Cup

··Incorrect carpet height setting

··Rotate nozzle control knob to lower setting

··Clogs in air flow passage

··

Clear clogs/clean filters as per manual instructions

Possible Cause

Possible Solution

··Dirt Cup improperly installed

··Re-install the Dirt Cup.

Problem : Dust escapes the Dirt Cup

Possible Cause

Possible Solution

··Strange sound like rushing air

··Check for clogs in hose, nozzle area and or

filters, clear or claen any clogs or blockages

as per manual instructions

Problem : Abnormal sound

Possible Cause

Possible Solution

··Incorrect carpet height setting

··Rotate nozzle control knob to lower setting

Problem : Cleaner hard to push

THis Vacuum cleaner is approved the following.

EMC Directive: 89/336/EEC, 92/31/EEC and 93/68/EEC

Low Voltage Safety Directive: 73/23/EEC and 93/68/EEC

If you have any comments or questions regarding a Samsung products,

contact the SAMSUNG customer care center.

Country

U.K

SOUTH AFRICA

Customer Care Center ☎

0870 242 0303

0860 7267864 (SAMSUNG)

Web Site

www.samsung.com/uk

www.samsung.com/za

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페이지9 i n

MMEEMMOO

DJ68-00294F(0.0) 2007.3.30 6:5 PM 페 이 지 1 0 i n

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Staubsauger Handbücher

Samsung

Samsung SC07F80 series Bedienungsanleitung

Samsung

Samsung SC6360 Bedienungsanleitung

Samsung

Samsung VC-7423V Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung SR8895 Bedienungsanleitung

Samsung

Samsung SC8571 Bedienungsanleitung

Samsung

Samsung SR8825 Bedienungsanleitung

Samsung

Samsung SC9210 Bedienungsanleitung

Samsung

Samsung VS20A95 Series Bedienungsanleitung

Samsung

Samsung SC20M25 Series Bedienungsanleitung

Samsung

Samsung VS20T755 Series Bedienungsanleitung

Samsung

Samsung DJ68 Bedienungsanleitung

Samsung

Samsung SC21F60 Series Bedienungsanleitung

Samsung

Samsung VC-RA84V Series Bedienungsanleitung

Samsung

Samsung SC07M31 Series Bedienungsanleitung

Samsung

Samsung SU8860 Bedienungsanleitung

Samsung

Samsung SC4750 User Manual (Windows 7) Bedienungsanleitung

Samsung

Samsung VAC-7049B Bedienungsanleitung

Samsung

Samsung VC-5815V Bedienungsanleitung

Samsung

Samsung SU4040 Bedienungsanleitung

Samsung

Samsung POWERbot VR20J9250U Series Bedienungsanleitung

Samsung

Samsung sc7400 Bedienungsanleitung

Samsung

Samsung SW7260 Bedienungsanleitung

Samsung

Samsung Jet Bot VR50T95 Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung