Sangean U-3 Bedienungsanleitung

User Manual

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5.Do not use this apparatus near water.

6. Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9.Do not defeat the safety purpose of the polarized or

grounding-type plug.Apolarized plug has two blades with one

wider than the other.Agrounding type plug has two blades and a

third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your

outlet. consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged. liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. To Reduce the Risk of Fire or Electric Shock,Do not Expose

ThisAppliance To Rain or Moisture.

16. The Shock Hazard Marking andAssociatedGraphical Symbol is

provided on the bottom panel of unit.

17.Apparatus shall not be exposed to dripping or splashing and no

objects filled with liquids, shall not be placed on the apparatus.

Control Tone Control

Aux In LED indicator

Power Button/Sleep

BuzzerAlarm

Buzzer

Light Switch

RadioAlarm

DC Input Socket

Open toAC Cord Compartment

DC Output Socket

Volume Control

Tuning Control/Time Set/Station Scan

FMAntenna

DC Out LED indicator

Band Selection

Speaker

Light

LCDDisplay

Preset station

Battery Compartment

AuxIn Socket

Headphone Socket

10 11

12 13

14 15

16 17

20 21

22 GB

LCD Display Preset Stations

Frequencyunit

HWS BuzzerAlarm

Sleep and Snooze Status

Time Set

Band Indicator

Battery Power

RadioAlarm

Frequency

PM for Clock

Clock

Power the radio

Note:

Insert back up battery prior to main batteries.

Back up battery is to back up the preset stations and also clock.

It is necessary to insert back up battery (2 x UM-3 1.5V, not supplied)

for memory back up even if you useAC power only. Without the back

up battery, time and preset station will get lost if removeAC power

cord fromAC outlet or duringAC power failure.

Back up battery compartment is located inside the main battery

compartment. Insert 2 xAAsize (UM-3) battery and ensure the

battery is inserted in accordance with the diagram shown.

1. Battery operation

Installing the batteries, first turn battery cover fixture anti-clockwise

to loosen and put down the battery cover. Insert 6 xDsize (UM-1)

battery into the compartment. Ensure the battery is inserted in

accordance with the diagram shown.

Close the battery cover and fasten the fixture by turning clockwise.

If the radio is not to be used for any extended period of time,

it is recommended that the battery is removed from the radio.

2. AC operation

Before you plug theAC cord into theAC socket, be sure the voltage

is correct. If you have batteries in the radio and use theAC power

cord, the batteries will automatically be disconnected.

Switch the “Open“ to theAC cord compartment to OPENposition,

pull back the compartment door and cylinder of theAC cord storage,

put out theAC cord to get the required length to theAC socket and

position theAC cord in the cut out in the lower right side of the

compartment door. Close the door.

You can store theAC cord after use in the opposite way you pull out

theAC cord.

3. Powered viaDC IN socket

The radio can be also powered via theDC INsocket which can allow

9-14 Volt DC, which is designed to be powered by the vehicle or the

boat so you can take the radio with you outdoors or on the boat.

An additional cigarette lighter cable is required (not supplied) for

this device.

Setting the clock

1. Clock can be set either the radio is power on or off.

2.Display will show “- : - -“ when the batteries are installed or when

the radio is connected to the mains supply.

3. Press inTuning control (Time Set) knob for more than 2 seconds,

display will flash time set symbol and also the hour digits,

followed by a beep.

4. Rotary Tuning Control (Time Set) knob to set the required hours.

5. Press in Tuning control knob, the minute digits will flash.

6. Rotary Tuning Control button to set required minute.

7. Press in Tuning Control button to complete time setting.

Operating the radio

This radio is equipped with three tuning methods – Scan tuning,

Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band button.

For FM band, be sure to screw in the rubber FM antenna properly

to get best reception. For MW (AM) band, rotate the radio to get

best signal.

3. Press and release Tuning Control /Time Set /Scan knob

(long press the knob more than 2 seconds will activate time

setting), the radio will up search and stop automatically when

it finds a radio station. Press the Scan button again to pick up

the found station.

Note:

The radio will continue to search next available stations if you

do not press Scan button again when it finds a radio station.

4. Rotate the Volume Control and Tone Control to get required

sound level.

5. To turn off the radio, press the Power button.

Display will show OFF.

Manual tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band button.

Adjust the antenna as described above.

3.Asingle press on either rotate theTuning Control knob will

change the frequency in the following increments:

FM: 50 or 100 kHz

MW (AM): 9 or 10 kHz

4. Rotate the Volume Control and Tone Control to get required

sound level.

5. To turn off the radio, press the Power button.

Display will show OFF.

Andere Handbücher für U-3

Inhaltsverzeichnis

Andere Sangean Tragbares Radio Handbücher

Sangean

Sangean WR-1 Bedienungsanleitung

Sangean

Sangean ATS-909X - WORLD BAND RADIOS Bedienungsanleitung

Sangean

Sangean LUNCHBOX Betriebsanleitung

Sangean

Sangean ATS-818 Bedienungsanleitung

Sangean

Sangean DT-120CL Bedienungsanleitung

Sangean

Sangean PR-D12 Bedienungsanleitung

Sangean

Sangean DT-120CL Bedienungsanleitung

Sangean

Sangean PR-D9W - Bedienungsanleitung

Sangean

Sangean Sangean- RCR-3 Bedienungsanleitung

Sangean

Sangean ProTravel PT-50 Bedienungsanleitung

Sangean

Sangean PR-D7 Bedienungsanleitung

Sangean

Sangean PR-D9W - Bedienungsanleitung

Sangean

Sangean WR-2 Bedienungsanleitung

Sangean

Sangean PR-D17 Bedienungsanleitung

Sangean

Sangean DT-120 Betriebsanleitung

Sangean

Sangean DT-120 Bedienungsanleitung

Sangean

Sangean DT-300 Bedienungsanleitung

Sangean

Sangean DT-210 Bedienungsanleitung

Sangean

Sangean LUNCHBOX Bedienungsanleitung

Sangean

Sangean SG-102 Bedienungsanleitung

Sangean

Sangean H201 Betriebsanleitung

Sangean

Sangean TOUGHBOX Bedienungsanleitung

Sangean

Sangean DT-120 Bedienungsanleitung

Sangean

Sangean ATS-909X - WORLD BAND RADIOS Benutzerhandbuch

Beliebte Tragbares Radio Handbücher anderer Marken

Telefunken

Telefunken P5 Bedienungsanleitung

Tait

Tait TP9300 Bedienungsanleitung

Lafayette

Lafayette Guardian 5500 Bedienungsanleitung

Sailor

Sailor SP3300 Bedienungsanleitung

Matra Nortel

Matra Nortel MC 6500 Bedienungsanleitung

Hytera

Hytera PD362i Bedienungsanleitung

Vertex Standard

Vertex Standard VX-P920 Series Bedienungsanleitung

Roberts

Roberts Ecologic 3 Bedienungsanleitung

LENCO

LENCO IPD-5100 Bedienungsanleitung

Baofeng

Baofeng BF-82 Bedienungsanleitung

Trevi

Trevi RA 764 Bedienungsanleitung

M/A-Com

M/A-Com P5100 Series Bedienungsanleitung

Elta

Elta 6699 Bedienungsanleitung

PURE

PURE ONE classic Series II Bedienungsanleitung

Teac

Teac PR130 Bedienungsanleitung

Philips

Philips AE6370 Bedienungsanleitung

Simoco

Simoco SRP9170 Bedienungsanleitung

Audiovox

Audiovox FR14 Bedienungsanleitung