Sanitaire Quick Kleen SC899 Bedienungsanleitung

COMMERCIAL UPRIGHT

VACUUM CLEANER

OWNER’S GUIDE

800 SERIES

(Model SC899 pictured)

Index

Important Safeguards.................... 2

General Information....................... 6

Assembly....................................... 6

Use................................................ 8

Fan Chamber .............................. 10

Dust Bag ..................................... 11

Brush Roll Belt............................. 12

Brush Roll (chrome steel)............ 13

Brush Roll (anodized aluminum) 14

Headlight ..................................... 14

Warranty...................................... 15

For location of nearest

Eureka/Sanitaire Warranty Station

or service information call

1-800-282-2886. www.eureka.com

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE USINGTHIS VACUUM CLEANER.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not use outdoors or on wet surfaces.

•Do not leave vacuum cleaner when plugged in.Turn off the switch and unplug the

electrical cord when not in use and before servicing.

•Do not allow to be used as a toy.Close attention is necessary when used by or near

children.

•Use only as described in this manual. Use only manufacturer’s recommended

attachments.

•Do not use with damaged cord or plug. If vacuum cleaner is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, return it to a

service center before using.

•Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord

around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord

away from heated surfaces.

•Connect to a properly grounded outlet only (refer to Grounding Instructions).

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Turn off all controls before unplugging.

•Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.

•Do not handle plug or vacuum cleaner with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep

free of dust, lint, hair, and anything that may reduce airflow.

•This vacuum cleaner creates suction and contains a revolving brush roll.Keep hair,

loose clothing, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

•Do not use without dust bag in place.

•Belt pulleys can become hot during normal use.To prevent burns, avoid touching

the belt pulley when servicing the drive belt.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline, or use in

areas where they may be present.

•Store your cleaner indoors in a cool, dry area.

•Keep your work area well lighted.

•Unplug electrical appliances before vacuuming them.

SAVE THESE INSTRUCTIONS

Grounding Instructions

This appliance must be grounded. If it should malfunction or breakdown, grounding

providesapath of least resistance for electric currenttoreducethe risk of electric shock.

This appliance is equipped with a cord having an equipment-grounding conductor and

grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

DANGER

Improper connection of an equipment-grounding conductor can result in risk of electric

shock. Check with a qualified electrician or service person if you are in doubt as to

whether the outlet is properly grounded. Do not modify the plug provided with the

appliance. If it will not fit the outlet, have proper outlet installed by a qualified technician.

This appliance is for use on a nominal 120 volt circuit and has a grounding plug that

lookslikethe plugillustratedin FigureA.Atemporaryadapter whichlooksliketheadapter

illustrated in Figure B may be used to connect this plug to a two-pole receptacle, as

shown, if a properly grounded outlet is not available.The temporary adapter should be

used only until a properly grounded outlet, Figure A, can be installed by a qualified

electrician.The green colored rigid ear, lug, or the like extending from the adapter must

be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adapter is used, it must be held in place by a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian

Electrical Code.

GROUNDED

OUTLET BOX GROUNDED

OUTLET BOX

FIGURE B

METAL

SCREW

ADAPTER

FIGURE A

GROUNDING BLADE

IS LONGEST OF THE

THREE BLADES

GROUNDING

TAB

CONSEILS DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent

être observées, incluant les suivantes:

LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.

AVERTISSEMENT

Pour réduire le risque de feu, de choc électrique, ou de blessure:

•Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.

•Fermezlecommutateur et débranchez l’appareil lorsque vous nel’utilisezpasou avant

le nettoyage ou l’entretien.

•Nepermettezpasqu’ilsoitutilisécomme jouet.Uneattentionparticulièreestnécessaire

lorsque utilisé par ou près d’un enfant.

•Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les

accessoires recommandés par le fabriquant.

•Ne pas utiliser si le cordon ou la fiche sont endommagès. Si l’aspirateur ne fonctionne

pas comme il le devrait, s’il a été échappé, s’il est endommagé, s’il a été laissé à

l’extérieur ou échappé dans l’eau, retournez-le à un centre de service avant de utiliser.

•Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de

poignée. Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou

bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le cordon à

distance des surfaces chauffantes.

•Branchez toujours l’aspirateur dans une prise à trois (mise à la terre).

•Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour

transporter le courant.

•Fermer tous les contrôles avant débrancher.

•Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le

cordon.

•Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.

•Nepasrien insérerdansles ouvertures.Nepasutilisersidesouverturessontbloquées;

assurez-vous qu’elles soient dégagées de poussière, mousse, cheveux ou toute autre

chose qui pourrait réduire le passage de l’air.

•Cetaspirateurcréedelasuccionetcontientunrouleau-brossetournant.Tenirlesparties

mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie du

corps.

•Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, alumettes ou

cendres chaudes.

•N’utilisez pas sans le sac de poussière en place.

•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour

prevenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la

courroie.

•Portez une attention particulière lorsque vous nettoyez les escaliers.

•Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de

l’essence: Ne pas utiliser dans les endroits où ces liquides pourraient être présents.

•Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.

•Maintenez un bon éclairage à l’endroit où vous travaillez.

•Débrancher les appareils électrique avant de les balayer.

CONSERVEZ CES INSTRUCTIONS

INSTRUCTIONS VISANT LA MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas défaillance ou de panne éventuelles, la

mise à la terre fournit au courant un chemin de moindre résistance qui réduit le

risque de choc électrique. Cet appareil est pourvu d’un cordon muni d’un

conducteur de terre et d’une fiche avec broche de terre. La fiche doit être branchée

dans une prise appropriée correctement installée et mise à la terre conformément

aux règlements et ordonnances municipaux.

AVERTISSEMENT

Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique.

Consulter un électricien ou un technicien d’entretien qualifié si vous n’étes pas certain

que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie avec

l’appareil-si elle ne peut être insérée dans la prise, faire installer une prise adéquate

par un électricien qualifié.

Note. Au Canada, l’utilisation d’un adaptateur temporaire n’est pas autorisée par le

Code canadien de l’électricité.

Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de mise à la terre

semblable à celle illustrée par le Figure A. S’assurer que l’appareil est branché à une

prise de courant ayant la même configuration que la fiche.Aucun adaptateur ne devrait

être utilisé avec cet appareil.

FIGURE A

Boîte de Prise deTerre

LA LAME DE TERRE

EST LA PLUS LONGUE

DES TROIS LAMES

Rating Plate

The model, type, and serial numbers are

indicated on the rating plate located on

the underneath side of the cleaner. For

promptandcomplete service information,

always refer to these numbers when

inquiring about service.

Model & Type ____________________

Serial No. _______________________

HOW TO ASSEMBLE

Assembly Packet

The assembly packet is with the owner’s

guide. The packet contains two 2-part

bolts and two cord hooks. An extra drive

belt is also included with some models.

Step 1

Assemble the Handle

Sliptheupperhandleand thelowerhandle

togetherso thehandle boltholesalign and

the slots in the handle are positioned as

shown in Detail A. Insert a 2-part bolt (A)

in the center of the handle and tighten.

Hold the assembled handle so it curves

away from the cleaner. Then push the

handle into the handle socket (D) at the

rear of the cleaner. Align the holes, insert

the other 2-part bolt (A), and tighten.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or

sharp objects with the cleaner to prevent bag tears, hose clogs, and fan blade breakage

with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional

service information telephone our toll free number for the nearest Eureka/Sanitaire

AuthorizedWarranty Station. Refer toThe Sanitaire CommercialWarranty for complete

service information. You should know the model, type and serial numbers when

you call: USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

DO NOT OIL the motor or the brush roll at any time. The bearings are

permanently lubricated and sealed.

MODEL TYPE SERIAL NO.

VOLTS AMPS. HERTZ

SERVICEINFORMATION:1-800-282-2886

Detail A

Step 2

Attach Upper Cord Hook

Pull the spring on the electrical cord

upward toward the top of the handle.

Make sure slots in handle are positioned

properly, see Detail A.

Insert the lower half of the spring into the

upper cord hook (B), as shown. Snap the

hook into the upper handle, directions

below.

Step 4

Install The Bag

Insert the bag adapter clip (E) on the

bottom of the bag collar into the bag

adapter retainer (F).

Push the bag collar up and forward so

the locator lug slides into the slot

indicated by the arrow. Then turn the

cam latch (G) to lock the bag onto the

rivet (H).

Loop the spring from the top of the bag

onto the bag support located to the back

of the upper cord hook (B).

Step 3

Attach Lower Cord Hook

Insert the power cord into the lower cord

hook (C), as shown. Snap the hook into

the lower handle. Pull up on the cord to

tighten but leave enough slack near the

base so the cord is not strained when the

handle is lowered.Wrap the cord around

the two cord hooks. Fasten the plug to

the cord to prevent unwinding.

3. SNAP opposite inner

tab into place

1. Place inner tab

into slot 2. Press hook

around handle

BAG

SUPPORT

HOOK

HOWTO USE

The upright vacuum cleaner is designed to be used on multiple types of carpeting.Do

not attempt to use the upright vacuum cleaner on bare floors, as damage to the

floor covering may result. Above the floor cleaning tools are available (optional).

Handle Adjustment

With the tip of the foot, press down to

release the handle lock located at the left

rear side of the cleaner.Move the handle

and adjust it to the desired position for

(1) storing upright, (2) operating the

cleaner at a comfortable height for the

user, and (3) cleaning underneath low

furniture.

Power Switch

The power switch is mounted on the

motor hood near the handle. Switch style

varies by model and may differ from the

illustration.A push with the foot turns the

motor ON; push again to turn the motor

OFF.

Edge Kleener®

EdgeKleener featureprovides forimprovedcleaningof carpets near wallsandstationary

furniture. Slots on the sides of the nozzle increase air flow to the edges of the cleaner

and add to the cleaning efficiency of the cleaner. To operate, simply run cleaner along

edge board. Edge Kleener operates instantly and automatically.

Cord Storage

The cleaner has two convenient cord storage hooks attached to the handle.Wind the

cord around the hooks and fasten the plug to the cord to prevent unwinding.

Handle Lock

1. Store

2. Use

3.Clean

Underneath

ON/OFF

Cleaner Height Setting

WARNING: Avoid injury. Keep loose clothing, hair, fingers,and all other parts of

body away from any moving part (such as the revolving brush).Turn

off the switch and unplug the cleaner before changing the cleaner

height setting.

Adjust the vacuum cleaner height setting to match the carpet pile height. Refer to the

following chart of recommended settings for carpet types.

Thefront of the cleaner haseithera knob

or slide adjustment which raises or

lowers the cleaner base to match the

type of carpet. With the cleaner cord

unplugged,set the adjustment according

to the table as a starting point. While

the cleaner is off and disconnected

from the outlet, place the handle in the

operating position, tilt the cleaner back

to remove the weight from the wheels,

and adjust the setting. Then plug the

cleaner into the electrical outlet, turn on

the switch, lower the handle, and pass

thecleaner over the carpet.Ifthe cleaner

is still difficult to push, follow the

procedure and test the cleaner at the

next higher setting. Continue testing the

setting until the cleaner is comfortable

to move. Moving the knob or slide to the

next higher setting raises the brush roll

slightly, making the cleaner easier to

push.However, the brush roll mustmake

contact with the carpet for effective

cleaning.

Recommended

Setting Example of Carpet

Position 1 Low pile as kitchen, indoor,

outdoor

Position 2 Sculptured

Position 3 Plush or thick sculptured

Position 4 Thick plush

Ifthe cleaner hasadditional height settings,they are forthicker

carpets or where easier pushing is desired.

HOWTO MAINTAIN

The instructions given in this booklet serve as a guide to routine maintenance. To avoid

unnecessary service calls, check the bag, belt and brush roll often.

Quick Kleen® Fan Chamber

NOTE: Turn off the switch and unplug the electrical cord before cleaning.

The clear, removable fan chamber cover provides easy

inspection, cleaning, and maintenance of the fan

chamber. Removing the cover provides easy access to

themotorfan. Greasebuildup,dirt, orother obstructions,

visible through the fan cover, should be removed. To

clean the fan area, take off the chrome bottom plate by

releasingthe two camlocks(see BrushRollBelt, Figure

1 and 2). Remove the belt from the motor pulley, then

loosen and remove the screws on either side of the fan

cover, as indicated by the arrows. Push the cam locks

outward against the wheels to lift the cover from the

cleaner base. Dirt and obstructions can easily be

cleared;however, cakedgreasemayneedto bescraped

from the cover and the cleaner. If the fan does not turn

freely, it also should be removed for cleaning. To remove the fan, place a wrench over

themotorpulley. Hold thefanbladeswithonehand andturnthe wrenchcounterclockwise.

Remove the motor pulley and lift the fan off the motor shaft. Clean the area and replace

the fan over the motor shaft. Tighten the motor pulley snugly clockwise with the wrench.

If necessary, replace the fan cover or the gasket with replacement parts.

Be sure the gasket is in place. Reposition the fan cover by first placing the exhaust end

into place between the large rear wheels. Seat the fan cover firmly. Next replace the

belt and bottom plate as the pressure from the bottom plate helps seal the fan cover.

Start the two screws by hand to be sure they are straight, then tighten.

Order fan chamber cover replacement kit (fan cover,gasket,two screws) Part No.

52334.

Cleaner Care

NOTE: Turn off the switch and unplug the electrical cord before cleaning unit.

To keep the vacuum cleaner looking new, it can be wiped with a damp cloth and a mild

soap solution, then thoroughly dried. Never use any type of chemical as chemicals can

damage the cleaner. When not in use, the cleaner should be stored in a clean, dry

place.

Inhaltsverzeichnis

Andere Sanitaire Staubsauger Handbücher

Sanitaire

Sanitaire Z4500 Series Bedienungsanleitung

Sanitaire

Sanitaire DuraLux SC9180 Bedienungsanleitung

Sanitaire

Sanitaire S3530 Series Bedienungsanleitung

Sanitaire

Sanitaire SC881A Handbuch

Sanitaire

Sanitaire Eon quietClean SC5500A Series Bedienungsanleitung

Sanitaire

Sanitaire 600 Series Bedienungsanleitung

Sanitaire

Sanitaire SC6075A Bedienungsanleitung

Sanitaire

Sanitaire System_Pro SP6952 Bedienungsanleitung

Sanitaire

Sanitaire SL4110A Series Bedienungsanleitung

Sanitaire

Sanitaire 880 Series Bedienungsanleitung

Sanitaire

Sanitaire SC3680 Series Bedienungsanleitung

Sanitaire

Sanitaire SC3680 Series Bedienungsanleitung

Sanitaire

Sanitaire SC600 Series Bedienungsanleitung

Sanitaire

Sanitaire S670 Bedienungsanleitung

Sanitaire

Sanitaire S107 Bedienungsanleitung

Sanitaire

Sanitaire SC5700 Series Bedienungsanleitung

Sanitaire

Sanitaire S780 System_Pro Bedienungsanleitung

Sanitaire

Sanitaire Canister Vac Bedienungsanleitung

Sanitaire

Sanitaire SC883A Handbuch

Sanitaire

Sanitaire HydroClean SC930A Bedienungsanleitung

Sanitaire

Sanitaire 580 Series Bedienungsanleitung

Sanitaire

Sanitaire SC2800 Series Bedienungsanleitung

Sanitaire

Sanitaire Quick Kleen SC886 Bedienungsanleitung

Sanitaire

Sanitaire EON QuietPro S5000A Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch