Satec PRO PM335 Gebrauchsanweisung

BG0635 REV.A1 ENGLISH PRO PM335 Quickstart www.satec-global.com

PRO PM335 Quick Start Manual

This guide instructs the user on installation, wiring, configuring and operating the PM335

multi-meter. This guide does not substitute the full user manual or the detailed safety

instructions. to download the manual and other related material, please visit our website:

www.satec-global.com

Warning! Only a licensed electrician may perform installations and wiring of the

PM335.

Figure 1: PM335 front panel

INSTALLATION

The PM335 is designed for 4-inch round / 92x92mm square panel mounting.

Please note to leave room for future expansion: when a basic units (no modules), it is

recommended to maintain a minimal gap of 30-100mm to the right (when facing front panel)

of the unit, allowing future installation of additional detachable SATEC modules (depending on

number of added modules: 17.8mm each).

PRO PM335 QuickStart www.satec-global.com

ELECTRICAL CONNECTIONS

The following steps correspond with a low-voltage three phase network (figure 2):

1. Make sure all power sources are disconnected.

2. Make sure that your designated power supply corresponds with the unit's rating.

3. Connect the power supply (bottom-left of front panel) via 12 AWG wires and a

designated circuit breaker.

4. Standard external current transformers: connect the CT's (14 AWG minimum) "+" pole

to the device's I1+current input (unit’s bottom right of rear end, as in figure 2) and the

"-" pole to the adjacent I1- current input. Repeat this for the following two phases, I2

and I3.

Verify proper polarity in your connections in accordance with the arrow printed on the

external CTs.

“HACS” CTs: connect the red/white wire to the "+" terminal and the black/orange

(colors vary according to the CT model) wire to the "-" terminal.

5. Connect the voltage measurement inputs (22-12 AWG; bottom-center of rear end).

6. Connect the com wire (26-12 AWG, shielded) to COM1 (RS485, top-left of rear-end).

7. Power-on the unit.

Figure 2: Electrical wiring

PRO PM335 QuickStart www.satec-global.com

BASIC CONFIGURATION AND OPERATION

The PRO PM335 is operated via the LCD display, 2 LEDs and 4 pushbuttons (figure 1: front

panel).

When powered on, the device will default to displaying voltages, for basic setup back up (<-

button) to the home screen navigate with arrows to “setup” (select with ), enter default

password (“9”) and select (“apply”). Open “general setup” to reveal “basic setup” for

configuration.

Figure 3: Screenshot sequence for basic setup

PRO PM335 QuickStart www.satec-global.com

CONNECTING OPTIONAL SATEC MODULES

1. DO NOT HOT-SWAP. When adding modules, make sure the unit is disconnected from

power supply

2. Remove cover (sticker on right side of unit) to reveal port

3. Attach the module tightly and tighten the clips

4. Power on the unit

GENERAL INFORMATION AND SYSTEM DEFAULTS

1. Default password: 9

2. Default IP: 192.168.0.203 (ETH1)

3. Default current mode (HACS model): Alternating Current (AC)

4. Default serial com settings (RS485): 19,200 Baudrate; address = 1

5. For convenient configuration please use SATEC’s PAS engineering software, connecting

your PC to the USB port (type C) at the right side of the front panel

To download PAS (free): www.satec-global.com/power-analysis-software

make sure to update .exe file with the most recent update available on webpage

Copyright © 2021 SATEC Ltd.

Inhaltsverzeichnis

Andere Satec Messgerät Handbücher

Satec

Satec PM135 Gebrauchsanweisung

Satec

Satec expertmeter EM720 Bedienungsanleitung

Satec

Satec PM172EH Series Bedienungsanleitung

Satec

Satec PM174 Series Bedienungsanleitung

Satec

Satec PM130 series Bedienungsanleitung

Satec

Satec PM290 Bedienungsanleitung

Satec

Satec PM130 PLUS Bedienungsanleitung

Satec

Satec Expertmeter PM180 Montage- und Bedienungsanleitung

Satec

Satec PNA295-1 Bedienungsanleitung

Satec

Satec PM130 PLUS Gebrauchsanweisung

Satec

Satec C191HM Bedienungsanleitung

Satec

Satec PM130P Bedienungsanleitung

Satec

Satec PM172P Bedienungsanleitung

Satec

Satec System 295 Bedienungsanleitung

Satec

Satec PRO EM235 Gebrauchsanweisung

Satec

Satec Expertmeter Series Bedienungsanleitung

Satec

Satec expertmeter EM720 Bedienungsanleitung

Satec

Satec PM130 series Bedienungsanleitung

Satec

Satec PM172P Betriebsanleitung

Satec

Satec PM172P Bedienungsanleitung

Satec

Satec PM172 Series Bedienungsanleitung

Satec

Satec PM130 series Bedienungsanleitung

Satec

Satec expertmeter EM720 Bedienungsanleitung

Satec

Satec PM290 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung