SCAN 30 Bedienungsanleitung

SCAN 30

INSTRUCTIONS FOR

INSTALLATION AND USE

This manual is accompanied by a

pamphlet with General Instructions

for Installation. Edition 10.04 - GB

MONTERINGSVEJLEDNING

med brugs- og fyringsanvisning

Indhold:

Generelle råd og anvisninger . . . . . . . . . .2-3

Reklamationsret

Type- og miljøgodkendelse

Udpakning

Tilbehør til din pejs

Montering af kakler og fedtsten

Kvalitetskontrol

Anmeldelsespligt

Skorstenstjek

Skorstensløsninger

Bærende underlag

Brændbar eller ikke brændbar væg

Gulvplade

Varmefordeling

Justerskrue

Typeskilt

Produktionsnr.

Servicepakke

Monteringsvejledning. . . . . . . . . . . . . . . . .4-7

Tilslutning til eksisterende/muret skorsten

Tilslutning topafgang til stålskorsten

Forbrændingsluft udefra

Brugs- og fyringsanvisning . . . . . . . . . . . 8-10

Vedligeholdelse af pejseovnen

Håndtering af brændsel

Optænding og fyring

Fejlsøgning . . . . . . . . . . . . . . . . . . . . . . . . 11

SCAN 3

BRUGSANVISNING

TildenneBrugsanvisninghørerogsåen

generelMonteringsvejledning.Udgave03.03-DK

MONTERINGSVEJLEDNING

medbrug

s-ogfyringsanvisning

Indhold:

Generellerådoganvisninger..........2-3

Reklamationsret

Type-ogmiljøgodkendelse

Udpakning

Tilbehørtildinpejs

Monteringafkaklerogfedtsten

Kvalitetskontrol

Anmeldelsespligt

Skorstenstjek

Skorstensløsninger

Bærendeunderlag

Brændbarellerikkebrændbarvæg

Gulvplade

Varmefordeling

Selvlukkendelåge

Justerskrue

Typeskilt

Produktionsnr.

Servicepakke

Monteringsvejledning.................4-7

Tilslutningtileksisterende/muretskorsten

Tilslutningtopafgangtilstålskorsten

Forbrændingsluftudefra

Brugs-ogfyringsanvisning...........8-10

Vedligeholdelseafpejseovnen

Håndteringafbrændsel

Optændingogfyring

Fejlsøgning........................11

Tildennemonteringsvejledninghørerogsåen

separatbrugsanvisningfordenenkeltepejs.

Udgave02/03-DK

Til dennemonteringsvejledning hørerogsåen

separatbrugsanvisning fordenenkelte pejs.

Udgave 02/03 - DK

Approved according to DIN 18891

1 Ashtray. When you open the cover under the door you

have access to the ashtray, which is placed below the

combustion chamber. Attention! Be careful when you

empty ashes from the stove. There may be embers left

for up to 24 hours after the stove was last used.

2 Lid for ashtray. Under the ashtray you will find a lid to

put on top of the ashtray when you carry it out for empty-

ing.

Handle for shaking grate. The stove is equipped with a

shaking grate. When you activate the grate handle, the

ashes from the combustion chamber are emptied into

the ashtray.

4 Regulation for primary air. Turn the air valve in order to

open. The primary air is used when lighting and refuel-

ling the stove. It should always be closed during continu-

ous firing.

The ashtray, shaking grate, and primary air should always

be closed during continuous firing.

Ceramic smoke deflector

Lift up the ceramic smoke deflector and push it sideways

until it is free of the combustion chamber brick. The deflec-

tor can now be removed through the combustion chamber.

You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We are convinced

that your stove will be to your full satisfaction and give you many hours of pleasure if you follow the advice and

instructions of this manual.

Please read this manual as well as the General Instructions for Installation before beginning the installa-

tion.

Congratulations on your new SCAN stove!

Cleaning of the glass

If you need to clean the glass, first make sure the stove

is cold. Open the door completely. Loosen the two bottom

screws to the left and to the right by means of the special

spanner (fig. a). Pivot the door upwards from below while

supporting it with your hand (fig. b) - do not let it fall. If

necessary, you can block the door with a piece of wood

while cleaning it. After cleaning the glass, pivot the door

back and mount the two bottom screws.

SCAN 30

Wood / briquettes Fuel kg/h (beechwood

max. 20% humidity)

SCAN 30 2 kg

Combustion air % 50-100

Primary air % 0

Adjustment of the air

Combustion air

Push the button sideways. Left

position is closed and right

position is open. The air is

used for combustion and regu-

lates the output of the stove.

Wires, wheels, and rails

If the wires, wheels, or rails that lift the door

should be damaged, you can access them by

removing the side panels. Lift them up and pull

them out.

Smooth operation of your wires and wheels

requires regular maintenance with a special

grease purchased through your local authori-

sed dealer.

Handle

The door is opened by pulling up the handle.

Self-closing door (BA 1)

The stove can be delivered with a self-closing

function at the factory.

Adjustment screws

The stove has two adjustment screws on the bot-

tom that can be used for levelling the stove.

Accessories

For this model you can have the following accessories:

• Thin or thick soapstone for

the baking shelf

• Thin or thick ceramic tile for

the baking shelf

• Closed cap for the baking

shelf

• Side panels in stainless steel

• Steel floor plate

• Connection piece for fresh-air

intake

You should read this manual as well as the General Instructions for Installation before beginning the installation.

SCAN 30

Data for calculation of the chimney

Stove

model

SCAN

Connecting

adaptor

Density of

flue gas

flow

g/s

Flue gas

tempera-

ture

Minimum

draft

Density of

flue gas

flow

g/s

Flue gas

temperature

Minimum

draft

0,8

Minimum

draft

30 150 - - - 6,5 345 14 11

With closed doorsWith open doors

Column 2 and 5 show the flue gas temperature in the connecting adaptor

Column 3 and 6 show the lowest/minimum draft in Pa by rated value

Column 7 shows the lowest/minimum draft in Pa by 0.8 x rated value

The stove can be prepared for an

external air supply where fresh air

is let directly into the combustion

chamber (must be mounted from

the factory).

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg

146

533 497

1040

878

150

Warranty conditions

All SCAN wood-burning stoves and inserts are made of first-class mate-

rial and are subject to a strict quality control before they leave the factory.

However, if an error should occur, we back all SCAN wood-burning stoves

and inserts with an extensive, five-year limited warranty.

See also the General Instructions for Installation delivered with your stove

for more details.

Technical info

Rated output: 7 kW

Min./max.: 3 - 9 kW

Weight: 130 - 180 kg

Connection piece, diameter: int. 135 mm / ext. 148 mm

*To the middle of the rear outlet

**Connection piece to fresh-air intake

Distances to flammable materials

(mm)

Production number

Write the production number of your

stove here so that you have it at hand in

case you need to contact us.

You can choose between several floor plates

in different shapes and dimensions for your

stove. Please contact your local authorities

concerning the security distances needed.

SCAN 30

Base plate

Radiation area

Base plate

200

300

800

500

200

300

500

800

Inhaltsverzeichnis

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung