SCAN 5004 FRL Benutzerhandbuch

5004 FRL

SCAN

ASSEMBLY AND INSTRUCTION MANUAL SCAN 5004 FRL

UK - ASSEMBLY AND INSTRUCTIONS MANUAL

SCAN

5004 FRL

You have purchased a product by one of Europe’s leading manufacturers of wood-bur-

ning stoves, and we are sure that you will have years of pleasure from your purchase.

To make the best possible use of your stove, it is important that you follow our advice

and instructions. Read through this Assembly and Instruction Manual carefully before

you start to assemble your stove.

SCAN

CONGRATULATIONS

ON YOUR NEW SCAN

BUILT-IN STOVE

SCAN 5004 FRL

CONTENTS

¬¬

TECHNICAL DATA 4

Installation 4

Safety 4

Technical data and dimensions 5

Dimension sketch Scan 5004 FRL 6

Type plate 7

Product registrationumber 7

¬¬

ASSEMBLY 8

Additional accessories 8

Disposal of packaging 8

Load-bearing foundation 8

Floor plate 8

Existing chimney and pre-fabricated element chimney 8

Connection between built-in stove and steel chimney 8

Requirements for chimney 9

Trim 9

Internal installation in non-ﬂammable material 9

Minimum distance to ﬂammable materials 9

Building in the stove at a ﬁre wall 9

Safety distance 9

Building into ﬂammable material with ﬁre wall 10

Before building the insert 11

Fresh air intake 12

Closed combustion system 12

Fresh air box 12

Door (Self-closing) 13

Clips for Norway (Large rooms) 14

Heat-storage system 14

Mounting of the heat shields/convection covers 15

Frames 18

Braces 21

Convection air 24

Mounting of convection grate 24

¬¬

INSTRUCTIONS FOR USE 25

Bafﬂe plates 25 Combustion air 25

¬¬

INSTRUCTIONS FOR HEATING 26

Environmentally friendly operation 26

Lighting 26

Using the stove in various weather conditions 26

Continuous operation 27

Warning about over-ﬁring 27

Firing in the spring or autumn 27

General notes 27

The function of the chimney 27

Chimney ﬁre 27

¬¬

HANDLING OF THE FUEL 28

Selecting wood/fuel 28

Preparation 28

Storing 28

Moisture 28

Use of the following as fuel is illegal 28

Caloriﬁc value of the wood 28

¬¬

MAINTENANCE 29

Sweeping the chimney and cleaning the stove 29

Checking the stove 29

Servicing 29

Combustion chamber lining 29

Gaskets 30

Painted surfaces 30

Disposal of stove parts 31

Cleaning the glass 31

¬¬

TROUBLESHOOTING 33

¬¬

WARRANTY 34

YOU GET THE BEST USE OF

THE STOVE BY USING

A TOP-DOWN

LIGHTING METHOD

SEE

"INSTRUCTIONS FOR HEATING"

PLEASE NOTE!

TECHNICAL DATA

INSTALLATION

¬ The house owner is responsible for ensuring that installation and assembly are in accordance with national and local building

regulations as well as the information provided in this Assembly and Instructions Manual

¬ When you install any kind of ﬁreplace or stove, you must inform the local building and housing authorities. In addition you are

obliged to have the installation inspected and approved by a local chimney sweep prior to commissioning

¬ To ensure best-possible functionality and safety for your installation, we advise you to call a professional ﬁtter. Your Scan

dealer will be able to recommend a qualiﬁed ﬁtter in your area. For information on Scan Dealers, please go to

www.scan-stoves.com

SAFETY

Any changes made to the product by the dealer, ﬁtter or user could result in the product and safety functions not functioning as

intended. The same applies to the ﬁtting of accessories or extra equipment not supplied by Scan A/S. This could also be the case

if parts that are necessary for the operation and safety of the stove are dismantled or removed.

TECHNICAL DATA AND DIMENSIONS

Test in compliance with EN 13229

CO Emission at 13% O20,09 %

CO Emission at 13% O21173 mg/Nm3

Dust @ 13% O225 mg/Nm3

Nox@ 13% O281 mg/Nm3

Efﬁciency 83 %

Energy efﬁciency index 110

Energy efﬁciency class A+

Nominel output 7,8 kW

Chimney temperature EN 13229 221 °C

Temperature in ﬂue conn. piece 265 °C

Amount of smoke 6,9 g/sek

Sub-pressure EN 13229 12 Pa

Recommended sub-pressure in

connecting piece 16-20 Pa

Required combustion air supply 20-35 m3/h

Fuel Wood

Fuel consumption 2,2 kg/h

Amount of fuel required to light 1,9 kg

Amount of fuel, max. 3,25 kg

Materials

Steel plate

Cast iron

Galvanised sheet

Chamotte

Surface treatment Senotherm

Max. log length 40 cm

Weight Scan 5004 FRL 210 kg

Weight Scan 5004 FRL

w/heat shield 218 kg

Flue conn. piece internal diameter 175 mm

Flue conn. piece external diameter 200 mm

Approval type Intermittend*

* Intermittent operation in this context means normal use of

a built-in stove. In other words, you should let the ﬁre die

down until only the embers are left before refuelling.

This built-in stove is produced in accordance with type

approval for the product, which also covers the product’s

Assembly and Instruction Manual.

The Declaration of Performance (DoP) is available from

www.scan-stoves.com.

Stove:

Path:

Articlenumber:

Material:

Date:

Constructed/Changed by:

SCAN A/S

DK-5492 Vissenbjerg©

Drawing

number:

Name:

C:\Working Folder\Designs\Scan 5004\95004001.idw

95004001

Målskitse 18-05-2017

Scan 5004

Weight: Area:

N/A N/A

1342

271

567

807

1086

127

267-314*520

733

*Note: Refer to the manual

for distance to combustible floor.

DIMENSION SKETCH SCAN 5004 FRL

All measures are in mm

*NB – remember to check the distance to ﬂammable materials.

AHeight to the beginning of ﬂue connecting piece at top outlet

BCentre of fresh air intake - Inside measure: 132 mm, Outside measure: 149 mm

CFlue conn. piece - Inside measure: 175 mm, Outside measure: 200 mm

SCAN 5004

- SCAN 5004

206A1X0032

2 / 109915

206A1X0032

Type plate Scan 5004 FRL

Product registration number Scan 5004 FRL

PRODUCT REGISTRATIONUMBER

All Scan built-in stoves are provided with a product registration number. Please make a note of this number at the rear page of

this manual; you will always need to quote it when contacting your dealer or Scan A/S.

TYPE PLATE

All Scan built-in stoves are ﬁtted with a type plate that speciﬁes the approval standards and the distance to ﬂammable materials.

The type plate is placed loose in the ﬁreplace.

ASSEMBLY

ADDITIONAL ACCESSORIES

¬ Fresh air box Ø149 cm (see page 12) ¬ Heat-storage stones (see page 14)

¬ Heat shields/convection covers (see page 15) ¬ Frames (see page 18)

¬ Braces with frames (see page 21) ¬ Convection air grid (see page 25)

DISPOSAL OF PACKAGING

Your Scan built-in stove may come supplied with the following packaging:

Wood packaging The wood packaging can be reused and after final use can be incinerated as a CO2neutral

product or sent for recycling

Foam Send for recycling or waste disposal

Plastic bags Send for recycling or waste disposal

Stretch/plastic ﬁlm Send for recycling or waste disposal

LOAD-BEARING FOUNDATION

All items in our product range come under the category of lightweight ﬁreplaces and stoves and do not normally require any

reinforcement of the beam structure. They can be positioned on ordinary beams/ﬂoor.

You should of course make sure that the foundation on which the stove is positioned can indeed support the weight of the stove

and, where applicable, a steel chimney, if you have opted for this solution. In case of doubt about the carrying capacity of the

ﬂoor, please consult a building expert.

FLOOR PLATE

If you are placing the stove on a ﬂammable ﬂoor, you must comply with the national and local regulations on the size of any

non-ﬂammable subsurface required to cover the ﬂoor around the stove.

Your local Scan dealer can advise you on regulations concerning protection of ﬂammable materials in the vicinity of your stove.

The ﬂoor plate’s function is to protect the ﬂoor and ﬂammable material against any sparks that may occur.

EXISTING CHIMNEY AND PRE-FABRICATED ELEMENT CHIMNEY

If you intend to connect your stove to an existing chimney, it makes sense to contact an authorised Scan dealer, or a local chim-

ney sweep, for advice. These experts will also let you know if your chimney needs renovating.

¬ When connecting a pre-fabricated element chimney, follow the manufacturer’s connection instructions for the

relevant chimney type.

CONNECTION BETWEEN BUILT-IN STOVE AND STEEL CHIMNEY

Your Scan dealer, or local chimney sweep, can advise you on choosing a make and type of steel chimney. This ensures that the

chimney will match your wood-burning stove.

REQUIREMENTS FOR CHIMNEY

The chimney must have a minimum internal diameter of 190 mm and have a T400 designation, with G for the soot ﬁre test. The

length should be min. 5 metres.

If you opt to connect the built-in stove with an elbow pipe, you should use a curved elbow, as this gives a better draught.

If you connect the stove with a sharp elbow pipe, the cleansing lid must be placed in the vertical part so that the horizontal part

can be cleaned through here.

If the chimney is ﬁtted with a smoke extractor, it must be possible to adjust it to a suitable draft.

The requirements to the chimney and the ﬂue pipe in terms of safety distances must be met.

¬ Choosing the wrong length or diameter of steel chimney could impair functionality

¬ Always comply exactly with the instructions provided by the steel chimney supplier

TRIM

The trim is mounted, when the surfaces of the covering are ﬁnished.

INTERNAL INSTALLATION IN NON-FLAMMABLE MATERIAL

When building or ﬁtting into structures that do not contain ﬂammable materials, a minimum distance of 10 mm must be main-

tained between the brickwork and the convection hood. This is to prevent cracks in the brickwork caused by the expansion of the

metal while the stove is heating. This construction does not require convection grates except for the convection air produced by

the convection box of the insert. However, please note that without convection grates, the effect of the insert will be lower.

MINIMUM DISTANCE TO FLAMMABLE MATERIALS

Distance to side: 400 mm - back: 400 mm - glass: 800 mm. - ceiling: 800 mm.

You should however assess whether furniture or other items might become excessively dry due to being too close to the stove.

¬ The stove is NOT to be built into ﬂammable materials without the use of a ﬁre wall and heat shields!

BUILDING IN THE STOVE AT A FIRE WALL

We refer to the building sketches on page 10.

SAFETY DISTANCE

European, national and local regulations concerning safety distances for wood-burning stoves and ﬂue pipes must be complied

with.

The stove must be set up so that the stove itself, the ﬂue pipe, and the chimney can all be cleaned.

/ EXISTING BRICKWORK

(WHICH IS NOT PROTECTED BY FIREWALL)

NAVN:

STI:

DIMENSION:

MATERIALE: DATO: SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg©

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 5004\95004002.idw

95004002

Opstillingsafstand m. varmeskjold

16-11-2017 sr

Scan 5004

VÆGT:

AREAL:

N/A

267mm

400mm

300mm

Min. 500 cm2

Min. 750 cm2

A-A ( 1 : 10 )

A A

NAVN:

STI:

DIMENSION:

MATERIALE: DATO: SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg©

TG.NR:

EMNE:

C:\Working Folder\Designs\Scan 5004\95004003.idw

95004003

Opstillingsafstand m. varmeskjold

Scan 5004

VÆGT:

AREAL:

N/A

100mm

25 mm

500 mm*

300mm*

Alle mål er minimusmål.

Møbleringsafstand: 800 mm til rude

Brandbart materiale

Brandmur F.eks. 50 mm Jøtul firewall, 110 mm mursten eller

andet materiale med tilsvarende brandfasthed og isolationsevne.

* Afstand til glas

NAVN:

STI:

DIMENSION:

MATERIALE: DATO: SIGN:

Krog Iversen & Co A/S

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 5004\95004092.idw

95004092

Opstillingsafstand m. varmeskjold Scan 5004 FRL

05-10-2018 sr

Scan 5004 FRL

VÆGT:

AREAL:

N/A

267mm

800mm

400mm

NAVN:

STI:

DIMENSION:

MATERIALE: DATO: SIGN:

Krog Iversen & Co A/S

TG.NR:EMNE:

C:\Working Folder\Designs\Scan 1005\91005029.idw

91005029

Uisoleret røgrør

23-01-2019 KEN

Scan 1005

VÆGT:

AREAL:

N/A

175

100

450

200

1500

800

Installation with an insulated, vertical ﬂue pipe

- structure/surround to ceiling

BUILDING INTO FLAMMABLE MATERIAL WITH FIRE WALL

Building in the Scan 5004 FRL with radiation shields against a ﬂammable wall protected by a ﬁre wall.

Lower

convection

opening

Upper

convection

opening

Floor

Ceiling

Flammable material

Fire wall, e.g. 50 mm Jøtul Firewall, 110 mm brick

or other material with corresponding ﬁreproof and

insulating abilities

All distances are in mm.

All distances are minimum distances

Distance to furniture: 800 mm. from glass

* Distance to glass

** Distance to ﬂammable ﬂoor

Insulated length

Ceiling

Installation with an insulated, vertical ﬂue pipe

- open structure/surround

Andere Handbücher für 5004 FRL

Inhaltsverzeichnis

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung