Scotsman TC 180 Handbuch

MV Modular Cuber

Cleaning & Sanitizing Procedure

Hubbard Ice Systems –0800 616559

Revision - 19/2/2011

Note - This document is to give the preferred instruction as to how cleaning and sanitising of the modular ice

machine is completed. This does not replace the instruction given within the full service manual, but to assist

and supplement it. Cleaning should only be undertaken by competent or trained personnel.

Note - Good hygiene working practice should be undertaken before and during any cleaning regime.

Cleaning Schedule

WARNING; Before carrying out any cleaning operation, please ensure that the ice maker is

disconnected from the electrical supply.

NOTE –If external stainless steel panels are not cleaned regularly, stains or water marks could begin

to show. It is important to prevent these stains forming on these stainless steel surfaces otherwise

there is a risk of a chemical reaction which could penetrate the chromium oxide film, this could

result in a ‘rust’ and ‘pitting’ of the panels.

Do not use abrasive products, such as steel wool pads, acids etc. Since these could damage the

various surfaces. In case of persistent stains, normal abrasive detergents or products specific for

stainless steel are readily available on the market.

Suggested Weekly Cleaning.

Pull out the removable condenser intake air filter on the side of the machine, vacuum to clean or

wash in clean water and dry, refit it in to the runner moulding once complete.

Wipe all external stainless steel panels & front panel assembly with a soft cloth and suitable

sanitising solution (Or pre-impregnated sanitizing wipes specific to the task).

Empty/Scoop out all the ice cubes stored into the storage bin below the machine in order to prevent

them from being contaminated with the cleaning solution used.

Wipe clean and rinse the inner surfaces of the storage bin using an appropriate sanitising product

along with the cleaning of the inside of the unit storage bin door.

Cleaning/Sanitising Procedure.

CLEANING/SANITISING INSTRUCTIONS OF WATER SYSTEM

Clean/Sanitise the water system, evaporator, bin and spray jets using a solution of a suitable

Ice Machine Cleaner/Sanitiser.

NOTE. Cleaning requirements vary according to the local water conditions and individual

user operation. Continuous check of the clarity of ice cubes and visual inspection of the water

spraying parts before and after cleaning will indicate frequency and procedure to be followed in

local areas.

Prior to the cleaning of the water system, it would be required to first clean the ice thickness sensor

and the water trough above the evaporator.

1. Wait until the end of the defrost/harvest cycle then push the RESET BUTTON for 6-8

seconds.

The machine should stop with the blinking of the Yellow LED (slow blink).

2. Remove the front unit panel & evaporator cover so to gain access to both the water sump

area and the evaporator section.

3. Remove the ‘ice thickness sensor’ from its bracket and clean by immersing the sensor into a

‘jug’ of descaling solution then with a cloth pre-soaked in a descaling solution (ensure both

the metal contacts & plastic bracket is cleaned to remove any mineral build up.

4. Disconnect the water hose from the tubing of the trough and remove the ‘water trough’

from its location by squeezing the retaining brackets, slide to the right and lift above the

evaporator so to then clean & rinse clear of any slime or scale build up.

5. Pour into the water sump, ‘Ice machine cleaner’ directly into the reservoir.

- MV 306-426 150 cc

- MV 456-606 250 cc

- MV 806-1006 350 cc

6. Push again the RESET BUTTON. The water circulating pump should start to operate with a

fast blinking of the Yellow LED while the water inlet valve will be energized to then the fill up

the water sump.

7. After approx 15 minutes (or longer if the scale build up is considered heavy), push again the

RESET BUTTON. The P.C. Board will now put the machine into an automatic rinsing mode

with the special blinking (blink twice and repeat) of the Yellow ‘Bin Full’ LED.

NOTE. The amount of Cleaner and the time needed for the cleaning of water system depends on the

water conditions locally.

NOTE: The RINSING mode consists of:

a) Energizing the water drain valve and the water pump for 40 seconds to empty the reservoir

b) De-energizing the water drain valve and the water pump for 1 minute

c) Energizing the water inlet valve until the water level fills up the water sump

d) Energizing the water pump for 1.5 minutes.

The above ‘rinsing’ sequence is automatically repeated 7 times so to be sure any possible trace of Ice

Machine Cleaner is removed.

8. At the end of the 7th Rinsing cycle, the P.C.Board stops the operation of the machine with

the blinking (slow) of the Yellow ‘Bin full’ LED

9. Pushing the RESET BUTTON for 6-8 seconds then sets the machine to restart in a new

freezing cycle.

10. Replace the sump covers, evaporator deflector cover and front unit panel.

11. Discard the next 2 batches of cubes made to ensure all the ice machine cleaner is removed

(no sour taste).

WARNING. The Ice Machine Cleaner/Sanitiser contain harmful fluids.

Please refer to any supplied MSDS document issued for handling of fluids.

KEEP OUT OF THE REACH OF CHILDREN.

If the water system is to then be sanitised, it is to be completed as per the preferred instruction

further down this document

Sanitising

NOTE. Sanitising of the water system is recommended to be done once every 3 months or more

frequent, depending on use.

1. Prepare in a plastic container the preferred sanitation solution as per manufacturer dilution

using cold water –approx a 10% ratio is suggested.

NOTE. Never mix the descaling solution with the sanitising solution.

2. Load into the empty ‘water sump’ then following the procedures as per cleaning/descaling

procedure (from point 6 ) just shortening then the operation of the unit ‘clean mode’ to 10

minutes for system sanitising.

3. Push the reset button x 1, to place unit into automatic ‘rinse’ mode (7 cycles).

4. At the completion of the sanitising cycle make sure of proper texture and clearness of the ice

cubes and that, they do not have any taste –test with the ‘testing’ strips to ensure removal

of all solution.

5. Allow the unit to make 2 batches of ice to then discard…………

ATTENTION. In case the ice cubes are cloudy-white and have an acidic taste, melt them

immediately by pouring on them some warm water. This to prevent that somebody could use

them.

6. Wipe to sanitise the inner surfaces of the pre-emptied storage bin before resuming normal ice

making operation.

Hubbard Ice Systems offers suitable product for the use for cleaning & sanitizing of all ice

dispensers, please call 0800 616559 for further detail and the appropriate MSDS data

sheets.

Andere Handbücher für TC 180

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Scotsman Eiswürfelbereiter Handbücher

Scotsman

Scotsman CME306 Bedienungsanleitung

Scotsman

Scotsman EC 46 Bedienungsanleitung

Scotsman

Scotsman MAR1400RL-32A Bedienungsanleitung

Scotsman

Scotsman iceValet HD22 Bedienungsanleitung

Scotsman

Scotsman MV Series Installationsanleitung

Scotsman

Scotsman TC 180 Handbuch

Scotsman

Scotsman Prodigy C2148 Leitfaden

Scotsman

Scotsman AFE400 Bedienungsanleitung

Scotsman

Scotsman CU0415 Installationsanleitung

Scotsman

Scotsman FME 1204 Bedienungsanleitung

Scotsman

Scotsman Air and Water Cooled C1448 Bedienungsanleitung

Scotsman

Scotsman F0522 Bedienungsanleitung

Scotsman

Scotsman CME1356R Bedienungsanleitung

Scotsman

Scotsman FM1202 Bedienungsanleitung

Scotsman

Scotsman HD356 Bedienungsanleitung

Scotsman

Scotsman CME1356 Bedienungsanleitung

Scotsman

Scotsman SCE170 Bedienungsanleitung

Scotsman

Scotsman MAR1400 Bedienungsanleitung

Scotsman

Scotsman SCCG30 Bedienungsanleitung

Scotsman

Scotsman MXG 328 Bedienungsanleitung

Scotsman

Scotsman MV 426 Betriebsanleitung

Scotsman

Scotsman NM1852 Bedienungsanleitung

Scotsman

Scotsman TC 180 Bedienungsanleitung

Scotsman

Scotsman FM2402R Bedienungsanleitung

Beliebte Eiswürfelbereiter Handbücher anderer Marken

Hoshizaki

Hoshizaki KMD-460MWJ Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Gebrauchsanweisung

Unold

Unold 48945 Bedienungsanleitung

Kenmore

Kenmore 2217402A Bedienungsanleitung

Cornelius

Cornelius WM600 Betriebsanleitung

GE XPIO43SCSS Bedienungsanleitung

Hoshizaki

Hoshizaki KMD-901MAH Bedienungsanleitung

Whynter

Whynter FIM-450HA Bedienungsanleitung

U-Line

U-Line UMCR014-SC01A Installationshandbuch

Andrew James

Andrew James AJ000522 Bedienungsanleitung

Kärcher

Kärcher IP 120 Bedienungsanleitung

U-Line

U-Line SS1095 Bedienungsanleitung

Maytag

Maytag MIM1554WRS - Ice Maker Bedienungsanleitung

Hoshizaki

Hoshizaki KM-630MAH Bedienungsanleitung

Princess

Princess Yonanas Bedienungsanleitung

Unold

Unold 48946 Bedienungsanleitung

Electrolux

Electrolux E15IM60GP Bedienungsanleitung

Cornelius

Cornelius UC150 ICE ONLY Bedienungsanleitung