Shuttle MVP Bedienungsanleitung

Page 1

Tower Installation

If you discover damaged or missing parts, please contact Shuttle Systems

[email protected] | 1-800-334-5633 9am-5pm Pacific Time

Page 2

Important Note:

PDF versions of these instructions are available at:

http://shuttlesystems.com/pages/faq

Assembly of the Shuttle MVP Towers requires two people.

Keep in mind that the following images pertain to just one of the three

available Shuttle MVP models, your parts may appear slightly different than

those in the included images but, the required steps remain the"

same.

If there is any shipping damage please take a photo of the damage and "

email to [email protected] or call (800)334-5633.

Tools Needed:

1/2 inch socket or combination wrench "

Allen wrench (provided in Parts Bag)

Socket Wrench Set

Typical combination wrench set

Page 3

MVP TOWER INSTALLATION

The Towers will come in one box

!1. Towers

- Towers"

!!- Wings"

!!- Parts Bag (Rope, Allen wrench, Pulley Systems)"

Head-End Stand"

(Head-End)

It is important to become familiar with the “Head-End” of the machine as it

refers to the end of the stand the Towers will be installed

Page 4

STEP 1

INSTALLING TOWER BASE

ITEMS

REQUIRED"

TOWER BASE"

1/2” SOCKET#

PARTS BAG

1. Remove the Kickplate Board. This can be done by unscrewing the 4 knurled knobs from

the back of the Kickplate Structure. (Pic 1.1)"

2. Remove the Carriage. This can be done by unscrewing the 4 Eyebolts and removing the 2

Knee Bumpers at the Head-End of the Rails. (Pic 1.2)"

3. Once the Kickplate Board and Carriage are removed, turn the Shuttle MVP on its side to

get access to the two feet at the Head-End Stand. This step is easier with two people.

4. Remove the two feet on the Head-End stand using a 1/2” socket and the included Allen

wrench in the Parts Bag. (Pic 1.4)"

5. Position and secure the Tower Base to the exposed bolt holes and tighten the two feet

back down. Once done flip the Machine upright and secure the Kickplate Board and

Carriage. (Pic 1.5)

Pictures are on the next page.

Page 5

1.1

1.2

1.4

1.5

Knee Bumpers"

Eye Bolts

Page 6

STEP 2

ATTACHING THE WINGS

ITEMS"

REQUIRED"

TOWER

WINGS"

PARTS BAG

1. Remove the top two bolts from the Head-End Stand and add the wings in alignment with

the now exposed bolt holes. (Pic 2.1)"

2. Using the hardware attached to the Wings, tighten down fully to the MVP Rails with the lock

nuts facing outwards. (Pic 2.2)"

3. Place the nut caps now exposed on the outside of the machine."

2.1"

2.2"

2.3

Page 7

STEP 3

ATTACHING THE TOWERS

ITEMS "

REQUIRED"

TOWERS"

PARTS BAG

1. Unwrap and remove the hardware from the Towers along with loosening the bottom bolt."

2. Position and attach the Towers onto the Plastic Blocks at the Head-End Stand. The Towers

should go out from the machine. (Pic 3.2)"

3. Insert the bolts that were originally attached to the Towers, through the Wings and out

through the Towers. Tighten once in position. (Pic 3.3)"

4. Secure the base of the Towers by tightening down the bottom bolts to the Plastic Blocks.

(Pic 3.4)

3.2

3.3

3.4

Page 8

STEP 4

INSTALLING THE PNF PULLEYS & ROPE

ITEMS "

REQUIRED"

ROPE CLEAT"

PNF PULLEYS"

ROPE

1. Attach the PNF Pulleys to the eyebolt at the desired height of both Towers. (Pic 4.1)"

2. Feed the rope through both Pulleys leaving the handles resting on the ground. (Pic 4.2)"

3. Located on the side of the carriage are two plastic hole inserts. Remove all 4 of the plastic

inserts from the carriage (2 on each side) and insert the Rope Cleat. Tighten down fully."

4. Secure the rope by pushing the rope into the Rope Cleat. The rope should not move

through the Cleat. (Pic 4.4).

4.1

4.4

4.2

Page 9

Finally, you have one of the greatest machines on earth....

Well, at least we'd like to think so - and many of our owners agree.

Therefore, enjoy it!

Leave us a review on our website!

Please visit us at:

www.ShuttleSystems.com

1-800-334-5633

Made in the

USA

Andere Handbücher für MVP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shuttle Fitnessgeräte Handbücher

Shuttle

Shuttle TNT Bedienungsanleitung

Shuttle

Shuttle MiniPress Bedienungsanleitung

Shuttle

Shuttle Shuttle Recovery Bedienungsanleitung

Shuttle

Shuttle Ultimate Bedienungsanleitung

Shuttle

Shuttle MVP Bedienungsanleitung

Shuttle

Shuttle TNT Bedienungsanleitung

Shuttle

Shuttle Z0-2734 Bedienungsanleitung

Shuttle

Shuttle BALANCE Bedienungsanleitung

Shuttle

Shuttle MVP Elite Plus Bedienungsanleitung

Shuttle

Shuttle TNT Bedienungsanleitung

Shuttle

Shuttle BALANCE Bedienungsanleitung

Shuttle

Shuttle BALANCE Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung