Shuttle HOT-637 Bedienungsanleitung

HOT-637

Pentium™IIprocessor

Based AGPMAINBOARD

User's Manual

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accor-

dance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.

Washington, DC 20402, Stock 004-000-00345-4

FCCWarning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate this equipment.

Note: InorderforaninstallationofthisproducttomaintaincompliancewiththelimitsforaClassBdevice,shielded

cablesandpowercordmustbeused.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic

compatibility :

- Immunity in accordance with EN 50082-1: 1992

- Emissions in accordance with EN 55022: 1987 Class B.

NOTICE

Manual Ver 1.0

All information, documentation, and specifications contained in this manual are subject to change without prior

notification by the manufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does

it make a commitment to update the information contained herein.

TRADEMARKS

Intel is a registered trademark of Intel Corporation

PentiumII Processor is a registered trademark of Intel Corporation

PC/AT is a registered trademark of International Business Machine Corporation.

PS/2 is a registered trademark of IBM Corporation.

All other brand and product names referred to in this manual are trademarks or registered trademarks of their

respective holders.

TABLEOFCONTENTS

PREFACE ...................................................................................................................3

CHAPTER 1 INTRODUCTION ...........................................................................................4

Specification ....................................................................................................................................... 4

Accessories of HOT-637 .................................................................................................................... 6

CHAPTER 2HARDWARE CONFIGURATION........................................................................7

ThePentiumII &Celeron Processor ................................................................................................. 7

Whatdoesthe RM(RetentionMechanism) consistof .....................................................................8

InstalltheRetention MechanismandHeat SinkSupport .................................................................9

InstallPentiumIIProcessor ............................................................................................................. 11

Celeron Processor S.E.P.P only RM Assembly Procedure .............................................................12

WhatdoesCeleron Processor RMconsistof .................................................................................. 13

InstallCeleronProcessor.................................................................................................................. 14

Jumpers.............................................................................................................................................. 15

ClearCMOS- J19............................................................................................................................. 17

FlashEEPROMVpp - J17................................................................................................................ 17

Keyboard PS/2Mouse Power-on setting -J44, JP8 ........................................................................17

Connectors & Sockets ...................................................................................................................... 18

CHAPTER 3MEMORY CONFIGURATION .........................................................................21

CHAPTER 4 FLASH UTILITY ........................................................................................22

CHAPTER 5 AWARD BIOS SETUP ..............................................................................24

The Main Menu................................................................................................................................. 25

StandardCMOSSetup...................................................................................................................... 27

BIOS Features Setup......................................................................................................................... 29

ChipsetFeatures Setup ..................................................................................................................... 32

PowerManagementSetup ................................................................................................................ 36

PCIConfigurationSetup .................................................................................................................. 39

IntegratedPeripherals ....................................................................................................................... 41

PasswordSetting............................................................................................................................... 44

PREFACE

HOT-637isa highly integratedIBMPC/AT compatiblesystemboard

designed to meet the industry's most demanding desktop applications.

Basedonthe Intel 82440LXAGPsetchipset, theIntelPentiumTMIIprocessor with

MMXtechnologyfeatured, and256KBor 512KB Level2 high-performance pipelined

burstsecondary168-pin DIMM socketandsupports up to512MBof EDO RAMand

SDRAM.

HOT-637isequipped withan AcceleratedGraphicsPort(A.G.P.), ahigh-performance

interconnectforgraphic-intensiveapplication,such as3D applications.TheA.G.P. is

independentofthe PCI busandis designedtoexclusively use withgraphical-display

devices.TheHOT-637 supports3.3V A.G.P.deviceswith datatransferrates upto133

MHz,allowingdata throughputof500 MB/sec.

TheIntel's82440LX AGPset chipsetprovides an integratedBusMastering IDEcontrol-

lerwithtwo highperformance IDEinterfaceswhich allowsupto fourIDE devices

connectionandup to 33MB/secof datatransferrates.

Theon-boardGiga I/Ocontroller providesstandardPC I/Ofunctions:

floppydriveinterface, two FIFOserialports, an InDAdeviceport and aSPP/EPP/ECP

capable parallel port.

HOT-637isbuilt with fourPCIlocal busslotsproviding a highbandwidthdata path for

data-movementintensivefunctions such asgraphics,and with threeISAslots.

HOT-637provides thefoundation forcost effective,high performanceand highly

expandableplatforms,whichdeliversthelatestin theIntel PentiumTM IIprocessor and

newadvancedchipsettechnology.

SPECFICATION

TheHOT-637Mainboard iscarefully designedforthe demandingPC userwhowants highperfor-

manceandmany intelligent featuresin a compactpackage:

IntelChipset:

FeaturesIntel's440LX AGPset withI/Osubsystems.

CPUSupport:

Intel Pentium®IIandCeleron processor233 ~333MHz.

VersatileMemorySupports:

Equipped with four DIMM sockets support168-pin3.3V SDRAM andEDODRAM memory

modules,totalmemory size upto512MB.

Configurablesupportfor ECC(Error CheckingandCorrecting)

PCIandISAExpansionSlots:

Providesfour32-bit PCI slotsandthree 16-bitISAslots.

AGPSlot:

SupportsAccelerated GraphicsPortcardsforhighperformance,component levelinterconnect

targeted at 3D graphical display applications.

OnboardGiGA-I/O:

ProvidesoneFloppyport;oneoptionalPS/2 mouseconnector; two high-speedUART compatible

serial ports and one parallel port with ECP and EPP capabilities. Serial Port 2 can also be directed

fromCOM2to the Infrared Moduleforwireless connections.

OnboardPCIBusMasterIDEController:

Two UltraDMA/33 BusMaster IDE Portssupportsfour IDEdevicesup to 33MB/sec IDE trans-

fersandsupports Enhanced PIOModes 3 and4and BusMasterIDE DMA Mode2 devices.

Onboard20-pinATXPower Supply:

ProvidesATXpower connectoronboardsupports soft-on/offfunction.

SystemBIOS:

ProvideslicensedAwardV4.51PGBIOSonFlashEEPROM.

SupportsGreenPC, DMIand BundledwithNCR SCSIBIOS.

ACPI:

Support ACPI(AdvancedConfigurationandPower Interface) function. ACPI provide more

EnergySavingFeatures forthe futureoperatingsystemsupportingOS DirectPowerManagement

(OSPM)functionality.

BoardSize:

ATX form factor 305mm x 170mm.

AdvancedFeatures:

CPUPlug& Play--HOT-637 featuringCPUPlug & Playfunction, the userneedn'tto adjust

onboardsystemclock andCPUmultiplier. When the systemfirst power-on, BIOSwillset CPU

clock speed to 233 MHz automatically. If your CPU speed higher than 233 MHz., one thing you

only have to do is entry BIOS to set CPU speed to the higher one.

LowEMI--Spread Spectrumbuiltin - ±1.5%modulation and automaticclockshut-off of unused

PCI/SDRAMSslotstoreducethe EMI.

DualFunctionPowerButton-- Thesystem can beoneof twostates, oneis Suspend modeand

the other is the Soft-off mode. Pushing the power button for less than 4 seconds will place the

systemintoSuspend mode. Whenpushthe powerbuttonfor morethan4 seconds,thesystem

enterstheSoft-off mode.

Wake-ON-LAN --The systemwill power-onautomatically byactivating ofLAN.

(Thisfunctionsupport Intel LANcardonly).

ModemRingPower-on --Thesystem willpower-onautomatically byactivatingof modemring.

PS/2Keyboard& Mouse Power-on --Thesystem will power-onautomaticallyby strokekey-

boardordouble clickPS/2mouse.

MoreAdvancedFeatures(option):

VoltagesMonitoring--Systemvoltages levelsare monitoredtoensure stablecurrentto main

boardcomponents.

Systemvoltagesinclude VCORE and VL2 for CPU, and +5V, +12V, -5V, -12V for system.

FANStatusMonitoring-- Toprevent CPUoverheat,CPU fansismonitored forRPMand failure.

(CPUCoolingFAN withRPM sensorisrequired)

ACCESSORIESOF HOT-637

HARDWARECONFIGURATION

The Pentium™ II & Celeron™ Processor

ThePentiumII and Celeron processoristhe next memberofthe P6 processorfamily. It

combinesthearchitecturaladvancesinthePentium Proprocessor withthe instructionset

extensionsofMMX technology. It isfullycompatible withthehuge base ofIntelarchitec-

ture-basedPCsoftware. Additional, the PentiumII processor deliversnewlevels ofperfor-

manceforadvance mediaand communicationssoftwareincluding powerful,realistic

graphicsandimaging capabilities, videoconference,and theabilityto run full-screen,full-

motionvideo. Thecombination oftheseadvanced technologiesmakes thePentiumII

processortheideal choicefoeexecuting modem 32-bitcompute-intensive and multimedia-

enhancedapplication workloads usingadvanced32-bitoperatingsystems.

ThePentiumII and Celeronprocessor both haveaseparate, 32KB,on-chip,non-blocking L1

cachewhichrun at theprocessorfrequency, Pentium IIprocessoralso has a512KBor

256KB on-board L2 non-blocking cache runs at half the processor speed.

ThePentiumII processor usingSingle Edge Contact(S.E.C.)cartridge packagingtechnol-

ogywhichenables highvolumeavailability, improvedhandling protection.

TheCeleronprocessor usingSingle EdgeProcessorPackage. (S.E.P.P.)

Figure2-1shows the front,rearand topviewsof Pentium IIprocessor(without heat sink

mounted).

Figure2-2shows theprimaryand non-primarysideof Celeronprocessorwithout heatsink

mounted and with heat sink mounted.

Figure 2-2

Figure 2-1

What does the RM (Retention Mechanism) consist of

PentiumIIprocessor requiresthe RetentionMechanism(RM) andoptional HeatSink

Support(HSS)to holdthebase processor inthe S.E.C. cartridge.

Followinginstallationprocedure willdisplay howtoinstall thesemechanism.

RetentionMechanismpackage consists of2separate partsandoptional Heat SinkSupport

consistsof3 separateparts.

Normally,dependon the typeofheat sink, HeatSinkSupport isnotalways available. For

someheatsink attachedon pentiumIIprocessor mightnotfit toinstall theHeatSink

Support.TheintroductionofHeatSinkSupport installationon thismanual onlyfor your

reference.

RetentionMechanism(RM) -

PlasticGuidewith captivenuts thatholdthe

S.E.C. Cartridge in the Slot1 connector.

(RefertoFigure 2-3)

RMAttachMount (RMAM)-

Bolt/Bridgeassemblies insertedupthrough

thebottomof the mainboard. Thensecures the

RMtoRMAM (twoRMAM requiredperRM).

(RefertoFigure 2-4)

Heat Sink Support Base (HSSBASE) -

Plasticsupportbarmountedtothemainboard

undertheATX heat sink.

(RefertoFigure 2-5)

HSSPin(HSSPIN) -

Plasticpinsinserted through theHSSBASEto secure

ittothe mainboard(tworequired perAssembly).

(RefertoFigure 2-6)

HSSTopBar (HSSTOP) -

PlasticbarthatclipsontotheHSSBASE

throughthefins on theATXheat sink.

(RefertoFigure 2-7)

Figure 2-3

Figure 2-4

Figure 2-5

Figure 2-6

Figure 2-7

Install the Retention Mechanism and Heat Sink Support

Placethemainboard on aworkbench (not inachassis). Besurethat the mainboardis bare

(thatis,no SIMMs, cables,or cards areinstalled).

Figure 2-8

Figure 2-9

InstalltheRetentionMechanism:

1.Findsout the RetentionMechanism(RM)

MountingHolesand "Pin 1" markofSlot 1

onHOT-661/Pmainboard.(RefertoFigure

2-8)

2.Installtwo RetentionMechanismAttach

Mounts(RMAM)with Bolt/Bridgeassem-

bliesinsertedup throughthebottom ofthe

mainboard.(Noticethe RMAM's bridge

orientationasFigure2-9)

3.Insertthe RetentionMechanism(RM)

around theSlot 1. Besure the SquareCut

Mark ofRM(Refer toFigure2-10) havethe

sameorientationof Slot1pin 1.(Referto

Figure2-9)

4. Screw the four captivenuts (Referto

Figure 2-10) on the RM by a screw drive to

secureRMto two RMANs.

Figure2-10

Inhaltsverzeichnis

Andere Shuttle Hauptplatine Handbücher

Shuttle

Shuttle AV42 Bedienungsanleitung

Shuttle

Shuttle FB83 Bedienungsanleitung

Shuttle

Shuttle Spacewalker MS50 Bedienungsanleitung

Shuttle

Shuttle Spacewalker HOT-685Z Bedienungsanleitung

Shuttle

Shuttle Spacewalker FE22 Bedienungsanleitung

Shuttle

Shuttle FB61 Bedienungsanleitung

Shuttle

Shuttle AI61 Bedienungsanleitung

Shuttle

Shuttle FT20 Bedienungsanleitung

Shuttle

Shuttle AB60/R Bedienungsanleitung

Shuttle

Shuttle MS52P Bedienungsanleitung

Shuttle

Shuttle Spacewalker AV30 Bedienungsanleitung

Shuttle

Shuttle SK41G Bedienungsanleitung

Shuttle

Shuttle Spacewalker AK32 Bedienungsanleitung

Shuttle

Shuttle MZ11 Bedienungsanleitung

Shuttle

Shuttle FV25 Bedienungsanleitung

Shuttle

Shuttle HOT-579 Bedienungsanleitung

Shuttle

Shuttle FT62 Bedienungsanleitung

Shuttle

Shuttle AV49 Bedienungsanleitung

Shuttle

Shuttle AK37GT Bedienungsanleitung

Shuttle

Shuttle AK35GT Bedienungsanleitung

Shuttle

Shuttle AB45 Bedienungsanleitung

Shuttle

Shuttle HOT-661/P Bedienungsanleitung

Shuttle

Shuttle HOT-595 Bedienungsanleitung

Shuttle

Shuttle FN95 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung