Siemens HL 3000 Bedienungsanleitung

Your

eye

in

hell

HL 3000 Manual

© Siemens Laser Analytics Sept 2000

Halogen lamp alignement manual

Document number: CID 3002-1103 Rev. 1A

LDS 3000 Operators manual HL 3002

1

1. HL 3002

1.1 General

Sometimes the visibility in the measurement path is poor. The reason for

this might be high dust load, smoke or strong ambient light from the

process (as in a combustion chamber). In this case a stronger light source

must be used in the first alignement step. Siemens Laser Analytics AB

can supply a suitable light source labelled HL 3000. This is a point source

using a 50 W halogen lamp and will produce a very luminous light spot -

normally easy to spot in the alignement procedure.

HL 3002 LDS 3000 Operators manual

2

1.2 The alignement procedure

The sensor is aligned using the sensor alignment kit AK 3002 together

with HL 3000. The aligning procedure is as follows:

Receiver side

1. Start by aligning the transmitter side. This is done by removing the

receiver at the quick connect interface and instead mount HL 3000

which defines the optical axis of the sensor pair. While the receiver is

dismounted - check that the lens is clean on the receiver and that the

purging is working.

Receiver side

HL 3000 generates a considerable amount of heat. Protective gloves should be ised

when it is handled.

Halogen alignement lamp

Note!

LDS 3000 Operators manual HL 3002

3

Transmitter side

2. Dismount the transmitter and check that the lens is clean on the

transmitter and that the purging is working. Then mount the trans-

mitter and twist-dismount the launcher (fiber cable connector in the

middle), twist-mount the cross hair instead. Align with the four bolts

on the flange, the light dot must be centred in the inner ring of the

cross hair.

Transmitter side

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

4

Transmitter side

3. Twist-mount the alignement lamp instead of the cross hair in the

transmitter.

Transmitter side

Alignement lamp

LDS 3000 Operators manual HL 3002

5

Receiver side

4. Mount the receiver back again and twist-mount the cross hair

instead of the detector module. Align with the four bolts on the

flange, the light dot must be centred in the inner ring of the cross

hair.

Receiver side

CD 3002 is now aligned and the holder for the fibre connector and the de-

tector module should be mounted in their places.

Finally, instrument air, or which ever method is used to protect the opti-

cal surfaces, should be connected to the appropriate inlets both at the

transmitter and receiver side of the sensor.

The mechanical stability of the sensor mechanics is sufficient to allow

dismounting (the quick connection) of both the receiver and the trans-

mitter. This means that cleaning of the lenses does not require re-align-

ment of the sensor.

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

6

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere Siemens Zubehör Handbücher

Siemens

Siemens SITRANS CU02 Bedienungsanleitung

Siemens

Siemens 5WG1 258-3AB11 Bedienungsanleitung

Siemens

Siemens SITRANS WM300 MFA Bedienungsanleitung

Siemens

Siemens HC15 Bedienungsanleitung

Siemens

Siemens QFM81.21 Bedienungsanleitung

Siemens

Siemens QPM11 Series Bedienungsanleitung

Siemens

Siemens milltronics WEIGHFEEDER 1200 Series Bedienungsanleitung

Siemens

Siemens DELTA 5TC1 01 Service-Handbuch

Siemens

Siemens RUGGEDCOM WIN7258 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN7025 Bedienungsanleitung

Siemens

Siemens 5WG1 201-2DBx3 Series Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN7237 Bedienungsanleitung

Siemens

Siemens S 564 Bedienungsanleitung

Siemens

Siemens Sitrans WM100 Bedienungsanleitung

Siemens

Siemens QNA2 D Series Leitfaden

Siemens

Siemens SIWAREX WL230 BB-S SA Bedienungsanleitung

Siemens

Siemens SITRANS WW100 Bedienungsanleitung

Siemens

Siemens 3VL9400-4PJ00 Bedienungsanleitung

Siemens

Siemens SIWAREX JB Bedienungsanleitung

Siemens

Siemens Symaro QSM2100 Bedienungsanleitung

Siemens

Siemens SITRANS LR 400 Bedienungsanleitung

Siemens

Siemens SITRANS AS100 Bedienungsanleitung

Siemens

Siemens SITRANS WS300 Bedienungsanleitung

Siemens

Siemens Milltronics Millpulse 600 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung