Siemens SIMATIC RF640T Gen 2 Bedienungsanleitung

SIMATIC RF640T Gen 2 1

SIMATIC Sensors

RFID systems

SIMATIC RF640T Gen 2

Operating Instructions

05/2009

J31069-D0197-U001-A2-7618

TAGnology RFID GmbH | Grazer Vorstadt 142 | 8570 Voitsberg | AUSTRIA

phone: +43 (0)3142/ 28 9 28-10 | fax: +43 (0)3142/ 28 9 28-20 | ofce@tagnology.com | www.tagnology.com

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be adhered to. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

J31069-D0197-U001-A1-7618

Ⓟ 05/2009

2007, 2008, 2009.

Technical data subject to change

SIMATIC RF640T Gen 2

Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618 3

Table of contents

1 SIMATIC RF640T Gen 2 ........................................................................................................................... 5

1.1 Characteristics ...............................................................................................................................5

1.2 Ordering data .................................................................................................................................6

1.3 Planning the use ............................................................................................................................6

1.3.1 Optimum antenna/transponder positioning with plane mounting of the transponder on

metal ..............................................................................................................................................6

1.3.2 Reading range on flat metallic carrier plates .................................................................................7

1.3.3 Reading range when mounted on non-metallic carriers ................................................................8

1.3.4 Influence of conducting walls on the reading range.......................................................................9

1.3.5 Directional radiation pattern of the transponder...........................................................................10

1.3.6 Use of the transponder in hazardous areas.................................................................................11

1.3.7 Use of the transponder in hazardous areas for gases.................................................................12

1.3.8 Use of the transponder in hazardous areas for dusts..................................................................13

1.4 Mounting instructions ...................................................................................................................14

1.5 Memory configuration ..................................................................................................................15

1.6 Technical Specifications ..............................................................................................................18

1.6.1 Mechanical data...........................................................................................................................18

1.6.2 Electrical data...............................................................................................................................18

1.6.3 Memory specifications .................................................................................................................19

1.6.4 Environmental conditions.............................................................................................................19

1.6.5 Chemical resistance of the RF640T Gen 2 transponder .............................................................20

1.7 Certificates and approvals ...........................................................................................................22

1.7.1 Certificates and approvals ...........................................................................................................22

1.7.2 Manufacturer's declaration RF640T Gen 2 UHF Tool Tag Version 1..........................................22

1.8 Dimension drawing ......................................................................................................................23

Table of contents

SIMATIC RF640T Gen 2

4 Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618

SIMATIC RF640T Gen 2

Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618 5

SIMATIC RF640T Gen 2 1

1.1 Characteristics

The SIMATIC RF640T Gen 2 transponder is a passive (i.e. battery-free) and maintenance-

free, round-shaped data carrier. It functions based on the UHF Class 1 Gen 2 technology

and is used for saving the electronic product code (EPC) of 96 bits/240 bits. The transponder

also has a 512-bit user memory.

Fields of application are industrial asset management, RF identification of tools, containers

and metallic equipment.

The tool tag is small, smart, and rugged, suitable for industrial applications with degree of

protection IP68. It is resistant to mineral oils, lubricants and detergents.

Preferably the SIMATIC RF640T is to be mounted direct on a flat metal surface of at least

150 mm diameter where it achieves a typical sensing distance of 4 m.

SIMATIC RF640T Gen 2 transponder Characteristics

Application Identification tasks in rugged industrial

environments

Europe USA / Canada Frequency versions

868 MHz 915 MHz

Air interface according to ISO 18000-6C

Polarization Linear

Memory EPC 96 bit/240 bit

Add-on-memory 64 bytes

Typically 4.0 m in connection with:

•RF660R readers and

•RF660A antennas

Typically 2.0 m in connection with:

•RF630R readers and

•RF660A antennas

Read/write range

Typically 2.0 m in connection with:

•RF620R with integrated antenna

Installation Suitable for direct mounting on conductive

materials (preferably metal)

SIMATIC RF640T Gen 2

1.2 Ordering data

SIMATIC RF640T Gen 2

6 Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618

1.2 Ordering data

Ordering data Order no.

SIMATIC RF640T Gen 2 (Europe)

•Frequency 865 MHz to 868 MHz

•EPC 96 bits/240 bits

•64-byte user memory

•-25 °C to +85 °C operating temperature

•Dimensions (D x H) 50 mm x 8 mm

6GT2810-2DC00

SIMATIC RF640T Gen 2 (USA/Canada)

•Frequency 902 MHz to 928 MHz

•EPC 96 bits/240 bits

•64-byte user memory

•-25 °C to +85 °C operating temperature

•Dimensions (D x H) 50 mm x 8 mm

6GT2810-2DC10

1.3 Planning the use

1.3.1 Optimum antenna/transponder positioning with plane mounting of the transponder

on metal

5)7

WUDQVSRQGHU

0HWDOVXSSRUW

5HFHLYHILHOG

5HFHLYH

7[DQWHQQD

5[DQWHQQD

7UDQVPLWILHOG

'LVWDQFHFP

5HDGLQJGLVWDQFHP

6HQG

Figure 1-1 Example of optimum antenna/transponder positioning

SIMATIC RF640T Gen 2

1.3 Planning the use

SIMATIC RF640T Gen 2

Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618 7

1.3.2 Reading range on flat metallic carrier plates

The transponder generally has linear polarization. The polarization axis runs as shown in the

diagram below. If the tag is centrically mounted on a flat metal plate, which may either be

almost square or circular, it can be aligned in any direction since the transmitting and

receiving RF660A antennas operate with circular polarization.

3RODUL]DWLRQD[LV

6TXDUH

PHWDOFDUULHUSODWH

&LUFXODUPHWDO

FDUULHUSODWH

r

Figure 1-2 Optimum positioning of the transponder on a (square or circular) metal plate

Table 1- 1 Reading range on flat metallic carrier plates

Carrier plate material Reading range

Metal plate of at least Ø 150 mm 100%

Metal plate Ø 120 mm Approx. 80%

Metal plate Ø 85 mm Approx. 55%

Metal plate Ø 65 mm Approx. 40%

On rectangular carrier plates, the reading distance depends on the mounting orientation of

the transponder

SIMATIC RF640T Gen 2

1.3 Planning the use

SIMATIC RF640T Gen 2

8 Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618

1.3.3 Reading range when mounted on non-metallic carriers

The transponder is generally designed for mounting on metallic objects which provide the

conditions for the maximum reading ranges

Table 1- 2 Reading range on non-metallic carriers

Carrier plate material Reading range

Transponder on wooden carrier Approx. 40%

Transponder on plastic carrier Approx. 35%

Transponder on plastic mineral water bottle Approx. 55%

Transponder without base Approx. 30%

100% reading distance refers to a metal plate of at least 150 mm diameter.

SIMATIC RF640T Gen 2

1.3 Planning the use

SIMATIC RF640T Gen 2

Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618 9

1.3.4 Influence of conducting walls on the reading range

If there are conducting walls or restrictions in the vicinity that could shade the radio field, a

distance of approx. 10 cm is recommended between the transponder and the wall In

principle, walls have least influence if the polarization axis is orthogonal to the conducting

wall.

Reading range: One conducting wall

Influence on reading range when positioned against one conducting wall

&RQGXFWLQJZDOO

3RODUL]DWLRQD[LV

Top view

Distance d 20 mm 50 mm 100 mm

Approx. 90 % Approx. 90 % Approx. 95 % Wall height 20 mm

Approx. 80 % Approx. 90 % Approx. 90 % Wall height 50 mm

Reading range

Approx. 70 % Approx. 75 % Approx. 90 % Wall height 100 mm

Reading range: Two conducting walls

Influence on reading range when positioned against two conducting walls

G

&RQGXFWLQJZDOO

3RODUL]DWLRQD[LV

0HWDOFDUULHU

Top view

G

0HWDOFDUULHU

&RQGXFWLQJZDOO

:DOOKHLJKW

&RQGXFWLQJ

ZDOO

Side view

Distance d 20 mm 50 mm 100 mm

Approx. 75 % Approx. 90 % Approx. 90 % Wall height 20 mm

Approx. 50 % Approx. 45 % Approx. 80 % Wall height 50 mm

Reading range

Approx. 40 % Approx. 45 % Approx. 75 % Wall height 100 mm

The values specified in the tables above must be complied with.

SIMATIC RF640T Gen 2

1.3 Planning the use

SIMATIC RF640T Gen 2

10 Operating Instructions, 05/2009, J31069-D0197-U001-A2-7618

1.3.5 Directional radiation pattern of the transponder

Preferably, align the tag parallel to the transmitting antenna. If, however, the tag including

the metallic carrier plate is tilted, the reading range will be reduced.

Rotation about the polarization axis

-25

-20

-15

-10

-5

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

$QJOHGHJUHHV

*DLQG%U

Figure 1-3 Transponder characteristics when rotated about the polarization axis

Inhaltsverzeichnis

Andere Siemens Zubehör Handbücher

Siemens

Siemens AP 257/41 Bedienungsanleitung

Siemens

Siemens SIMATIC RF640A Bedienungsanleitung

Siemens

Siemens QVM62.1 Bedienungsanleitung

Siemens

Siemens 3VL9500 - 4PA30 Bedienungsanleitung

Siemens

Siemens QAA4292.EWSC Bedienungsanleitung

Siemens

Siemens SIWAREX JB Bedienungsanleitung

Siemens

Siemens 5WG1 258-3AB11 Bedienungsanleitung

Siemens

Siemens SIMATIC VS120 Bedienungsanleitung

Siemens

Siemens 5WG1 201-2DBx3 Series Bedienungsanleitung

Siemens

Siemens Opto-BERO K50 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN7225 Bedienungsanleitung

Siemens

Siemens SITRANS AS100 Bedienungsanleitung

Siemens

Siemens SITRANS WM300 MFA Bedienungsanleitung

Siemens

Siemens S 564 Bedienungsanleitung

Siemens

Siemens WiPS-200 Series Bedienungsanleitung

Siemens

Siemens BS-240 Stücklistenhandbuch

Siemens

Siemens SIMATIC Vision Sensor VS 130-2 Bedienungsanleitung

Siemens

Siemens TC63 Einrichtungshandbuch

Siemens

Siemens milltronics MFA 4P Bedienungsanleitung

Siemens

Siemens SITRANS WS100 Bedienungsanleitung

Siemens

Siemens SIMATIC VS130 Series Bedienungsanleitung

Siemens

Siemens MC35 Terminal Einrichtungshandbuch

Siemens

Siemens RUGGEDCOM WIN7258 Bedienungsanleitung

Siemens

Siemens SITRANS LG240 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung