Siemens FDCIO422 Service-Handbuch

SIEMENS

Industry, Inc.

A6V10324662_g_en_US

2016-01-20 Building Technologies Division

Model FDCIO422

Addressable Input/Output module S54322-F4-A1

Installation Instructions

Download link

Desigo:

https://www.buildingtechnologies.siemens.com/extranet/ba-sp/

Download link Cerberus PRO:

http://iknow.us009.siemens.net/infolink

INTRODUCTION

The FDCIO422 is used for the connection of up

to 2 independent Class A or 4 independent

Class B dry N/O configurable contacts. Input

lines can be supervised for open, short and

ground fault conditions (depending on EOL

termination resistor and class configuration).

Inputs can be independently configured via the

fire control panel for alarm, trouble, status or

supervisory zones.

The FDCIO422 has 4 programmable outputs

with 4 potential-free latching type form A relay

contacts for fire control installations.

Status indication per LED for each input and

output plus 1 LED for general status of the

device. Power supply via FDnet (supervised

power limited).

·Including 4 EOL devices (470 Ω)

·3 separators to separate the power limited

wiring from the non-power limited.

Separators are delivered in 3 different sizes

for standard 4 11/16-inch box, 4 11/16-inch

extension ring and 5-inch box (RANDL).

CAUTION

Electric shock!

High voltages may

occur on the terminals.

Always use a faceplate

and the separator(s).

Figure 1 FDCIO422 cage and carrier

CAUTION

This device is not intended for

applications in explosive environments.

Class A is equivalent to DCLA (Canada)

Class B is equivalent to DCLB (Canada)

For complete configuration and

commissioning of the FDCIO422 also refer

to the user documentation of your panel,

especially for the software tool used for

configuration.

Figure 2 Removing the cage and the terminal strips from the carrier

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

PROGRAMMING INSTRUCTIONS

Refer to Figure 3 to locate the opening on the

cage cover that allows access to the programming

holes which are on the FDCIO422 printed circuit

board.

To connect the FDCIO422 to the DPU or 8720

Programmer/Tester, insert the plug from the

DPU/8720 cable provided with the

Programmer/Tester into the opening on the front

of the FDCIO422. Be sure to insert the locating

tab on the plug into the slot for the locating tab as

shown in Figure 3. Minimum Firmware revision of

the DPU must be 9.00.0004, for 8720 must be

5.02.0002.

NOTICE

To prevent potential damage to the DPU

(refer to manual P/N 315-033260) or to

the 8720 (refer to manual P/N 315-

033260FA) DO NOT connect a FDCIO422

to the DPU or 8720 until the cage is

removed from the carrier (Figure 2).

Figure 3 Connecting the DPU/8720 plug to the cage

Modul Status LED

Flash Color

Condition

Flash Intervals

(Seconds)

Green

Normal supervisory operation.

Amber

Device is in trouble

Red

Locate

Alarm

Input/Output active

No Flashes

Device is not powered, or

replacement is needed.

LED can be turned off. Please follow the corresponding

description of the Panel used.

WIRING

Refer to Figure 11. Refer to the appropriate wiring diagram and wire the addressable input/output module

accordingly.

Recommended wire size: 18 AWG minimum and 14 AWG maximum

Wire larger than 14 AWG can damage the connector.

(Refer to Figures 2 and 3). Follow the instructions in the DPU manual or 8720 manual to program the

FDCIO422 to the desired address. Record the device address on the label located on the front of the

module. The FDCIO422 can now be installed and wired to the system.

Figure 4 Wiring multiple switches

INPUT NOTES:

1. There can be any number of normally open dry contact switches.

2. The end of line device must be located at the last switch.

3. Do not wire a normally closed switch across the end of line device in a normally open wiring.

4. Multiple switches: for open wiring supervision only.

INPUT ACTIVE LED,

red

INPUT TROUBLE LED,

yellow

PLUG FROM DPU/8720

PROGRAMMER/TESTER

LOCATING

TAB

OUT A

OUT B

OUT C

OUT D

IN 1

IN 2

IN 3

IN 4

IN 1 trouble

IN 2 trouble

IN 3 trouble

IN 4 trouble

SLOT FOR

LOCATING TAB

PROGRAMMING

HOLES

OUTPUTACTIVE LED,

red

Command for the activation

of the output received by the

control unit

PROGRAMMABLE SWITCHES (SEE NOTES 1, 2 AND 3)

PROGRAMMABLE SWITCHES (SEE NOTES 1 AND 3)

Rp ½ W470 Ω

EOL

UL 864 CLASS STYLE

IN 1-4

IN1/IN2

IN3/IN4

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

Power limited wiring

In compliance with NEC Article 760, all power

limited fire protective signaling conductors must be

separated a minimum of ¼ inch from all of the

following items located within an outlet box:

·Electric light

·Power

·Class 1 or non-power limited fire protective

signaling conductors

To meet the above requirements, the following

guidelines must be observed when installing this

input/output module.

If non-power limited wiring is not used

within this outlet box, then these

guidelines do not apply. In that case, be

sure to follow standard wiring practices.

Wiring entering outlet box

All power limited wiring must enter the outlet box

separately from the electric light, power, class 1,

or non-power limited fire protection signaling

conductors. For the FDCIO422, wiring to the

terminal blockfor line and inputs must enter the

outlet box separately from the terminals for

outputs.

For the output terminals, protection with a fuse is

recommended. Refer to Figures 6 and 9.

WIRING AT THE TERMINAL BLOCKS

Minimize the length of wire entering the

outlet box.

Figure 6 Power Limited Wiring

Separators

The separators must be used when the relay

contacts are connected to non-power limited lines.

Mount the correct separator in the box used

(4 11/16-inch box and 5-inch box). If an extension

ring is used in connection with a 4 11/16-inch

square box an additional separator has to be

mounted in the extension ring.

The separators create two compartments to

separate the wires as shown in Figure 5.

Figure 5 Mounting the separators in the boxes

DO NOT USE!

P = POWER LIMITED

N = NON-POWER LIMITED

11 16

ADAPTER PLATE

11 16

4 INCH SQUARE BOX

WITH EXTENSION RING

INCHES DEEP (29.5 in³)

1½

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

MOUNTING

Input/output module FDCIO422 can be mounted

directly into a 4 11/16-inch square box or 5-inch

square box.

An additional extension ring can be mounted on

the 4 11/16-inch square box with two screws.

For mounting the input/output module in the

5-inch square box use a 4 11/16-inch adapter

plate.

Fasten the module to the square box with the

4 screws provided with the box.

Fasten the faceplate on the carrier using the

2 screws provided with the FDCIO422.

Be sure to program the FDCIO422 before

fastening the faceplate to the unit.

Volume allowance FDCIO422

FDCIO422 Volume 11.7 inch

max. 20 conductors

Check NFPA70, National Electric Code

‘314.16 Number of Conductors in Outlet,

Device and Junction Boxes, and Conduit’,

Table 314.16(A) and (B), to choose the

correct metal box (4 11/16-inch square box,

411/16-inch square box with extension ring

or 5-inch square box).

WARNING

It is not allowed to use the module without

the faceplate. Remove the faceplate for

service and maintenance reasons only!

Figure 7 Mounting the FDCIO422

TECHNICAL DATA

Operating voltage: DC 12 – 32 V

Operating current

(quiescent): 1 mA

Absolute maximum

peak current: 1.92 mA

Maximum current

connection factor2):4

Relays output

(normally open /

normally closed)

DC 30 V / AC 125 V

Max. 4x 5 A or

2x 7 A (OUT B, C) or

1x 8 A (OUT C)

Operating

temperature: 32 – 120 °F / 0 – 49 °C

Storage temperature: -22 – +140 °F / -30 – +60 °C

Humidity: 5 – 85 % R.H. (not freezing

and condensing at low

temperature)

Communication

protocol: FDnet (supervised Signaling

line circuit, Power limited)

Color: Carrier: ~RAL 9017

Cage cover: transparent

Cage: ~RAL 9017

Faceplate: white

Standards: UL 864, ULC-S 527, FM 3010,

UL 2572

Approvals: UL / ULC / FM

System compatibility FC2005, FC2025, FC2050,

FV2025, FV2050, FC901,

FC922, FC924, FV922,

FV924 & FireFinder XLS

Dimensions: 4.1 x 4.7 x 1.2 inch

Volume (cage and

carrier): 11.7 inch

2 coil latching type, dry contact, Form A

Average charge current of the device. 1 Load Unit (LU)

equals to 250 µA

11 16

ADAPTER PLATE

11 16

4 INCH EXTENSION RING

INCHES DEEP (29.5 in³)1½

FDCIO422

CONTROL MODULE BARRIER

(SUPPLIED)

FACEPLATE

5 INCHES

(SUPPLIED)

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

Figure 8 Line wiring

WIRING NOTES:

6.All supervised switches must be held closed and/or

open for at least 0.25 s to guarantee detection

(depending on filter time).

7.End of line device: 470 Ω± 1 %, ½W resistor,

delivered with the device (4x).

8.The inputs must be wired potential-free.

9.FDCIO422 is polarity insensitive. Line -6 and Line -5

can be either line of the loop.

10. Electrical ratings:

FDnet voltage maximum: DC 32 V

Absolute maximum peak current: 1.92 mA

11. Supervised switch ratings:

Monitoring voltage: 3 V

Cable length input: Max. 200 ft

Input shielding required

for cable lengths from: 30 ft – 200 ft

Max. C

Line

line

:0.02 µF

Max. C

Line

shield

:0.04 µF

Max. line size: 14 AWG

Min. line size: 18 AWG

12. The operating current may never exceed the rated

current.

13. As the outputs are not supervised by the module

use an external supervision for critical applications.

14. Choose the correct AWG size for the intended

operating current.

15. Connect incoming and outgoing shields together in

an acceptable means. Insulate shields, do not make

any connections to the device or back box.

16. Use shielded and/or twisted wire to connect the

switch wiring and keep the wiring as short as

possible.

17. Tie the switch wiring shield to the local earth

ground (at only one end, refer to Figure 9). For

multiple switches on the same input, connect

incoming and outgoing shields together in an

acceptable means. Insulate shields, do not make

any connections to the device or back box.

18. Positive and negative ground fault detected at

<25 kΩfor inputs 1 – 4.

·The shield from the input must be

connected to a known good earth

ground for proper operation.

We recommend to use the earth

connector in the electrical box.

·Conductive armored or conductive

metal conduit cables are sufficient as

shielding.

If a proper connection of the shield to

a known good ground cannot be

assured then unshielded cabling

should be used.

Figure 9 Input shielding

19. Relay contact ratings:

Cable length output: Max. 200 ft

PROGRAMMABLE

RELAY CONTACTS

SEE NOTES 12, 13, 14 AND 19

FROM CONTROL PANEL

OR PREVIOUS

ADDRESSABLE DEVICE

TO NEXT

ADDRESSABLE DEVICE

END OF LINE DEVICE Rp

SEE NOTE 7

SUPERVISED

PROGRAMMABLE SWITCH

SEE NOTES 6, 8 AND 11

PROGRAMMABLE

RELAY CONTACTS

SEE NOTES 12, 13, 14 AND 19

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

Normally open / Normally closed:

Define intended max. ambient temperature (77 °F, 100 °F, 120 °F) andmax. power factor from load.

Then find correlated possible max. current ratings in table below:

up to DC 30 V up to AC 125 V

P.F. / Amb. Temp. 0 - 77°F / 0 - 25°C ≤100°F / ≤38°C ≤120°F / ≤49°C 0 - 77°F / 0 - 25°C ≤100°F / ≤38°C ≤120°F / ≤49°C

resistive 14x 5 A

2x 7 A

1x 8 A

4x 3 A

2x 4 A

1x 5 A

4x 2 A

2x 2.5 A

1x 3 A

4x 5 A

2x 7 A

1x 8 A

4x 3 A

2x 4 A

1x 5 A

4x 2 A

2x 2.5 A

1x 3 A

inductive 0.6 4x 5 A

2x 5 A

1x 5 A

4x 3 A

2x 4 A

1x 5 A

4x 2 A

2x 2.5 A

1x 3 A

4x 5 A

2x 7 A

1x 7 A

4x 3 A

2x 4 A

1x 5 A

4x 2 A

2x 2.5 A

1x 3 A

inductive DC 0.35

AC 0.4

4x 3 A

2x 3 A

1x 3 A

4x 3 A

2x 3 A

1x 3 A

4x 2 A

2x 2.5 A

1x 3 A

4x 5 A

2x 7 A

1x 7 A

4x 3 A

2x 4 A

1x 5 A

4x 2 A

2x 2.5 A

1x 3 A

4x Out: A,B,C,D ; 2x Out: B,C ; 1x Out: C ; use only indicated outputs

PF 0.6 (60 Hz) ≡L/R max. 3.5 ms

PF 0.35 (60 Hz) ≡L/R max. 7.1 ms ≡max. ind. Load at any case

Diagnostics

NOTICE

AC ratings MUST NOT be used with modules

with ES<10. You will find the ES on the label.

Indication

Actions

Normal, no fault is present

In-/Output module is fully functional none

Fault is present

Error with the input circuitry (open line, short circuit, deviation) Checking the input circuitry (parameter setting,

resistors, short-circuit, open line)

Invalid parameter settings Check the parameter setting

Supply error - Check detector line voltage

- Replace device

Software error (Watchdog error) Replace device

Storage error Replace device

Communication error between device and control panel Remedy cause

Note: Any general message can be displayed together with another status.

Configuring the outputs Configuring the inputs

For configuring the outputs, proceed as follows:

a.Determine in which position the contact is

active. The contact can be active when it is:

- Closed (normally open, NO)

- Open (normally closed, NC)

b.After activating the contact remains:

– Permanently active

– Active only for a certain period of time. How

long the contact remains active can be

configured as well (pulse duration). This is only

to be used in the application of:

●Resetting the four wire device F5000

Reflective Beam Smoke Detector, P/N 500-

050261.

The following settings are possible:

10 s 15 s 20 s

c.Determine the behavior of the output in case of

error on the communication line (open line to

the control panel, FDCIO422 power failure).

The following configurations are possible for

the behavior in case of a failure (default

positions):

– Output position remains the same as

before the error

– Output is activated

– Output is deactivated

For configuring the inputs, proceed as follows:

a.Configure the inputs as 4 Class B (DLCB) or

2 Class A (DLCA).

b.Define the type of input (danger input or status

input):

- Status input: triggers status change

- Danger input: triggers alarm

c.Determine the type of monitoring and the

monitoring resistors (refer to Figure 10):

- Class A only open no EOL

- Class B only open RP470 Ω

- Class B open and short RS100 Ωand RP470 Ω

d.Define the input filter time. The following settings

are possible:

0.25 s 0.5 s 1 s

The configuration of the input must

correspond to the actual wiring.

An EOL must be mounted to the input in case of this

input is NOT used.

Follow the instructions in the

corresponding panel manual for

programming the FDCIO422 properly:

P/N A6V10333724 and

P/N A6V10336897.

Siemens Industry, Inc.

Building Technologies Division

A6V10324662_g_en_US

2016-01-20

·The 2x Class A inputs are identified by the panel as Input 1 and Input 2.

·Class A and Class B cannot be configured at the same time!

2x Class A or 4x Class B!

Figure 10 FDCIO422 input wiring Class A and Class B (for details of Line 1 and 2 wiring see Figure 8, for details of the

input wiring see Figure 11.)

OUT A

OUT B

OUT C

OUT D

OUT A

OUT B

OUT C

OUT D

OUT A

OUT B

OUT C

OUT D

470 ±1 % ½ W

Rs RpRp

please order separately

ORDER NO. S54312-F7-A1

100 ±1 % ½ W

ONLY OPEN MONITORING

UL864 CLASS STYLE

included

Siemens Industry, Inc.

Building Technologies Division

8, Fernwood Road

Florham Park, New Jersey 07932

www.siemens.com/buildingtechnologies

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Data and design subject to change without notice.

Document ID

Edition

A6V10324662_g_en_US

2016-01-20

End of Line Resistor Wiring Overview

①CAUTION: FOR SYSTEM SUPERVISION – FOR TERMINALS IDENTIFIED WITH A ①DO NOT USE

LOOPED WIRE TERMINALS. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS.

②Use Siemens TB-EOL terminal P/N S54322-F4-A2 or equivalent.

③Use only normally open dry contact SWITCHES for the inputs

Figure 11 Wiring end of line and switch

Use a 4 or 2 pole UL/ULC recognized SWITCH.

Switch Terminal must be capable of two conductors at one terminal.

EOL Resistor wiring must be done according to UL 864 and ULC-S527, chapter ‘EOL Devices’.

·The EOL Resistors must be connected at the end of the input lines.

No addressable device or 2

wire smoke detectors can be connected to the inputs.

ACCESSORIES

DEVICE

ORDER NO.

EOL resistor 100

Ω

S54312

SIEMENS

INDUSTRY, INC.

/16

inch adapter plate (optional)

411000

RANDL

INDUSTRIES, INC.

inch Box (optional)

T55017

RANDL

INDUSTRIES, INC.

inch Box (optional)

T55018

RANDL

INDUSTRIES, INC.

inch Box

(optional)

T55019

RANDL

INDUSTRIES, INC.

EOL terminal

S54322

SIEMENS

INDUSTRY, INC.

SHIELDED WIRE MAX: 200 FT

18 - 14 AWG

OPEN AND SHORT SUPERVISION

OPEN

CLASS B STYLE C, OPEN AND SHORT WIRING SUPERVISION

SHIELDED WIRE MAX: 200 FT

18 - 14 AWG

OPEN SUPERVISION

OPEN

IN1

EARTH

GND

CLASS A STYLE D, OPEN WIRING SUPERVISION CAUTION: BE AWARE OF THE INPUT POLARITY IN CLASS A MODE

SHIELDED WIRE MAX: 200 FT

18 - 14 AWG

OPEN

EARTH

GND

CLASS B STYLE B, OPEN WIRING SUPERVISION

OPEN SUPERVISION

EARTH

GND

470 Ω

100 Ω

470 Ω

for UL: mount EOL directly on the last SWITCH terminal for ULC: mount EOL on the TB-EOL terminal

①

TB-EOL ②

SWITCH ③

SWITCH ③SWITCH ③

①

③

SWITCH

①

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens Simatic S7-1500 Stücklistenhandbuch

Siemens

Siemens Simatic 6DL2804-0 Series Bedienungsanleitung

Siemens

Siemens DI 8x24VAC/48VUC BA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic S7-1500/ET 200MP Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Technisches Dokument

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Stücklistenhandbuch

Siemens

Siemens SIMATIC PROFINET Stücklistenhandbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 Kurzanleitung

Siemens

Siemens SIMATIC ET 200AL Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Bedienungsanleitung

Siemens

Siemens SIM-16 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Siemens

Siemens 6ES7141-6BG00-0BB0 Technisches Dokument

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Siemens

Siemens SIMATIC ET 200S M151-3 PN Bedienungsanleitung

Siemens

Siemens Simatic 6DL2804-1 Series Montageanleitung

Siemens

Siemens SIMATIC ET 200eco PN Bedienungsanleitung

Siemens

Siemens simatic ET 200MP Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 / ET 200MP Bedienungsanleitung

Siemens

Siemens DQ 16x24VDC/0.5A HF Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung