Siemens SIMATIC ET 200SP HA DQ 32x24VDC/0.5A HA Bedienungsanleitung

SIMATIC

ET 200SP HA

Digital output module DQ

32x24VDC/0.5A HA

(6DL1132-6BL00-0PH1)

Manual

09/2018

A5E39265993-AA

Security information 1

Preface 2

Product overview 3

Wiring 4

Parameters 5

Displays and interrupts 6

Technical specifications 7

Drivers, parameters,

diagnostics messages and

address space A

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be

used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property

damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified

personnel are those who, based on their training and experience, are capable of identifying risks and avoiding

potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or

approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described.

Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in

this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E39265993-AA

Ⓟ 10/2018 Subject to change

Table of contents

1 Security information......................................................................................................................................5

2Preface.........................................................................................................................................................7

3Product overview..........................................................................................................................................9

3.1 Properties of the I/O module DQ 32x24VDC/0.5A HA.............................................................9

4Wiring.........................................................................................................................................................11

4.1 Pin assignment of the I/O module DQ 32x24VDC/0.5A HA (1-wire connector).....................11

4.2 Pin assignment of the I/O module DQ 32x24VDC/0.5A HA (2-wire connector).....................13

4.3 Schematic circuit diagram......................................................................................................14

4.4 Pulling I/O module in runtime / output disable switch activated.............................................15

5 Parameters.................................................................................................................................................17

5.1 Parameters of the I/O module DQ 32x24VDC/0.5A HA.........................................................17

5.2 Module/channel parameters...................................................................................................18

5.3 Explanation of the module/channel parameters.....................................................................19

6 Displays and interrupts...............................................................................................................................21

6.1 Status and error displays of the I/O module DQ 32x24VDC/0.5A HA....................................21

6.2 Interrupts................................................................................................................................24

7 Technical specifications..............................................................................................................................25

A Drivers, parameters, diagnostics messages and address space...............................................................29

A.1 Concept of the driver and diagnostics blocks.........................................................................29

A.2 Parameters, diagnostics messages and address space without PCS 7................................31

A.2.1 Parameter assignment...........................................................................................................31

A.2.2 Parameter assignment and structure of the module/channel parameters.............................32

A.2.3 Diagnostics messages and maintenance events...................................................................34

A.2.4 Address space.......................................................................................................................35

Index...........................................................................................................................................................37

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

Manual, 09/2018, A5E39265993-AA 3

Table of contents

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

4Manual, 09/2018, A5E39265993-AA

Security information 1

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines, and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines and

networks. Systems, machines and components should only be connected to the enterprise

network or the internet if and to the extent necessary and with appropriate security measures

(e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. You can find more information about industrial security by visiting:

https://www.siemens.com/industrialsecurity.

Siemens’ products and solutions undergo continuous development to make them more secure.

Siemens strongly recommends you apply product updates as soon as available and always

use the latest product versions. Use of product versions that are no longer supported, and

failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

https://www.siemens.com/industrialsecurity.

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

Manual, 09/2018, A5E39265993-AA 5

Security information

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

6Manual, 09/2018, A5E39265993-AA

Preface 2

Validity of the documentation

This manual describes the following I/O module:

System family I/O module Article number

SIMATIC;

Distributed I/O System;

ET 200SP HA

DQ 32x24VDC/0.5A HA

6DL1132-6BL00-0PH1

It supplements the

ET 200SP HA Distributed I/O system

system manual.

Functions that generally relate to the system are described in this manual.

The information in this device manual and the system/function manuals enables you to put the

ET 200SP HA into operation.

Configuring the ET 200SP HA

You can configure the following components of the ET 200SP HA when the following updates

are installed:

Component of the ET 200SP HA Required updates

DQ 32x24VDC/0.5A HA HSP0276 V02.00.00

Appendices

The appendices provide information that is relevant for using the ET 200SP HA outside the

PCS 7 environment.

Conventions

Please also observe notes marked as follows:

Note

A note contains important information on the product described in the documentation, on the

handling of the product or on the section of the documentation to which particular attention

should be paid.

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

Manual, 09/2018, A5E39265993-AA 7

Preface

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

8Manual, 09/2018, A5E39265993-AA

Product overview 3

3.1 Properties of the I/O module DQ 32x24VDC/0.5A HA

View of the module

DIAG MT



DQ HA

32x24V DC/0, 5 A

DQ . 6 +

DQ . 0 +

DQ . 2+

DQ . 4 +

1P1

L+

24VDC

1P2

2P1

L+

24VDC

2P2

MAX. 10 A

V 1.0.0

CC 00

PW R

6DL1132-6BL00-0PH1

X 2

3 4

DQ . 7+

DQ .1+

DQ . 3 +

DQ . 5 +

DQ a

DQ . 6 +

DQ . 0 +

DQ . 2+

DQ . 4 +

DQ . 7+

DQ.1+

DQ . 3 +

DQ . 5 +

DQ b

2324

17 18

19 2 0

2122



DQ . 6 +

DQ . 0 +

DQ . 2+

DQ . 4 +

DQ . 7+

DQ.1+

DQ . 3 +

DQ . 5 +

DQ c

DQ . 6 +

DQ . 0 +

DQ . 2+

DQ . 4 +

DQ . 7+

DQ.1+

DQ . 3 +

DQ . 5 +

DQ d



.0 .1

.2 .3

.4 .5

.6 .7

DQ a



.0 .1

.2 . 3

.4 .5

.6 .7

DQ b

.0 .1

.2 . 3

.4 .5

.6 .7

DQ c

.0 .1

.2 . 3

.4 .5

.6 .7

DQ d

①Module type and designation ⑧Output disable switch

②LED for diagnostics ⑨Module type color coding

③LED for maintenance ⑩Product version

④2D matrix code ⑪Function status and firmware version

⑤Wiring diagram ⑫Color code for selection of the color-coded labels

⑥LEDs for channel status ⑬Serial number

⑦LED for supply voltage ⑭Article number

Figure 3-1 View of the DQ 32×24VDC/0.5A HA

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

Manual, 09/2018, A5E39265993-AA 9

Properties

The I/O module has the following technical properties:

● 32 digital outputs with the following properties that can be individually configured for each

channel

– Diagnostics

– Substitute values

● Source output (PNP, switching to P potential)

● Module-specific configurable diagnostics for missing supply voltage L+

● Output current (Total current of all channels: Max. 10 A; single channel: Max. 0.5 A)

● Suitable for solenoid valves, DC contactors, and indicator lights

The I/O module supports the following functions:

● Firmware update

● I&M identification data

● Parameter reassignment in RUN

● Value status QI

You can configure the I/O module with HW Config and integrate it into your system.

Output disable switch

If you want to pull the I/O module in runtime, you have to press the output disable switch for

3 seconds for the I/O module to be deenergized.

When the output disable switch has been pressed for 3 seconds, the LED DIAG flashes red,

the LED MT lights up yellow and the I/O module generates a diagnostics message. See section

Status and error displays of the I/O module DQ 32x24VDC/0.5A HA (Page 21).

Note

Pressing the output disable switch interrupts any ongoing firmware update. A firmware update

cannot be performed when the device is deenergized.

Accessories

The following accessories must be ordered separately:

● Labeling strips

● Color-coded labels

● Reference identification label

● Shield connector

Product overview

3.1 Properties of the I/O module DQ 32x24VDC/0.5A HA

Digital output module DQ 32x24VDC/0.5A HA (6DL1132-6BL00-0PH1)

10 Manual, 09/2018, A5E39265993-AA

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens SIMATIC ET 200eco PN Technisches Dokument

Siemens

Siemens 6ES7547-1JF00-0AB0 Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP DI 8x24VDC ST Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens Simatic ET200pro Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens CASTOMAT ION ANALOGINPUT T001 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200iSP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SIMOTICS CONNECT 400 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA2711-1CA00 Bedienungsanleitung

Siemens

Siemens PPM-1U32.BPR Bedienungsanleitung

Siemens

Siemens FDCIO222 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC SM 335 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung