Siemens ABHW-4BZ Bedienungsanleitung

A6V10806895_en--_d

Siemens Industry, Inc.

Building Technologies Division

Installation Instructions

Model ABHW-4BZ

Intelligent Audible Base

Introduction

The Model ABHW-4BZ audible base from Siemens Industry,

Inc. consists of a standard base combined with an audible

device. It is an intelligent supervised audible base which

provides 6 selectable tone patterns, 2 volume levels and 2

different power types for alarm (loop power or external power)

by using system configuration tool when ABHW-4BZ used with

the FD-UL compatible detectors (refer to “Compatible fire

alarm control panels”, “Compatible detector ”,“Detector

Placement” and “Tone and Volume Selection”). The ABHW-

4BZ audible bases in the same device loop are fully

synchronized with FD-UL detectors and also support RL-HC,

RL-HW remote lamp. The ABHW-4BZ provides Steady,

Temporal 3, Temporal 4, Temporal 4 low power, March time

120 and Canadian March time 30.

ABHW-4BZ is fully compatible with all Siemens addressable

detectors (see Compatible detectors section) and recognizes

the detector type automatically.

Application

note

The ABHW-4BZ is a UL268 & ULC-S529 listed smoke detector

supplementary device which combines detector base and

audible device functions. It meets or exceeds 85dB at 10 foot

audibility requirement as specified in UL268. When used in

conjunction with listed, compatible Siemens equipment, the

ABHW-4BZ

may be used in lieu of single/multiple station smoke

alarms to achieve enhanced, system-level functionality.

The ABHW-4BZ

can also meet requirement specified in UL464,

UL2075 and ULC-

525 except 520Hz requirements for “Sleeping

Area”.

pecifications

Physical Specifications:

Operating temperature: 32°F ~ 120°F (0°C ~ 49°C)

Operating humidity: 10 ~ 95%RH (Non Condensing)

Compatible electrical mounting boxes: 4” square gang box

ONLY with 2.5 inch depth minimum; 4” octagon box is

NOT compatible

Sound Output:

High: ≥85dB

Low: ≥75dB

Tones:

Steady

Temporal 3

Temporal 4

Temporal 4 low power

March time 120

Canadian March time 30

Electronic Ratings:

Operating voltage:

Loop power: 16 ~ 33 Vdc

External power: 16 ~ 33 Vdc

Supervisory current (max):

From loop: 250 µA

From external: 20 uA

Alarm current (RMS max):

Loop powered:

High dBA: 7.5 mA

Low dBA: 4.5 mA

External powered:

High dBA: 8.0 mA

Low dBA: 3.5 mA

Constraints 1. If the alarm current of ABHW-4BZ is energized by an

external power supply, any UL listed 24VDC regulated

power supply including the aux power output of XLS,

FC2005/FC901, FC2025/FC2050/FV2025/FV2050,

FC922/FC924/FV922/FV924 and PAD-3/PAD-4/PAD-5 can

be used (refer to Figure 1); or a 24VDC NAC, such as PAD-

3/PAD-4/PAD-5 (refer to Figure 3), ZIC-4A (FireFinder-XLS

zone indicating card (NAC), refer to Figure 2) and NAC from

FC2005/FC901 (refer to Figure 4.1)

or NAC from FC2025/FC2050/FV2025/FV2050, FC922/

FC924/FV922/FV924 (refer to Figure 4.2).

2. The alarm current of ABHW-4BZ CAN’T be energized by a

24V FWR power supply.

3. The maximum number of ABHW-4BZ is related to the max.

current rating and the power line resistance of the external

power supplies applied on the ABHW-4BZ. Refer to the

related installation instructions of the auxiliary power supply.

4. Refer to Figure 5 for “Loop Powered”.

The maximum number

of “loop powered” ABHW-4BZ is limited by the max. load

capacity and devices loaded in loop. Refer to APPENDIX-A

in this document to calculate the max. number of “loop

powered” ABHW-4BZ audible bases.

5. The maximum device line resistance cannot exceed the

maximum device line resistance specified in the compatible

panels.

6. T-tapping of the notification appliance circuit is not allowed.

7. The NAC output must be set to a steady DC if it is used for

ABHW-4BZ.

onfiguration

Important!

The ABHW-4BZ must be configured by the panel when it is

connected with FD-UL detectors (see table 1). Failure to

configure the ABHW-4BZ will cause problems. For additional

information please refer to the manual of related panel. Also for

use with H-Series detectors (see table 2) it does not require

panel configuration as it will function the same as an ADBH-11

which will not be synchronized.

etector

wiring

(Refer to Figure 6,7) Audible base Model ABHW-4BZ should

be interconnected as shown in the Installation/Wiring

Diagrams and wired to the specific system modules and

control panels following the appropriate instructions. For

operation with FireFinder-XLS, FC2005/FC901,

FC2025/FC2050/FV2025/FV2050,

FC922/FC924/FV922/FV924 system, note any limitations on

the number of audible bases permitted on each notification

appliance circuit or 24VDC regulated power supply, depending

on the total cable resistance and load of each circuit. (See

Electronic Ratings section.)

Note: Recommended wire size: 18 AWG min.; 14 AWG max.

Wire larger than 14 AWG can damage the connector.

etector

mounting

The detector base comes from the factory prewired. All

signaling and initiating circuits are connected directly to the

back of the ABHW-4BZ audible base using the four position

terminal blocks.

ase

mounting

1. Route all wires out from the outlet box.

2. When the alarm LED viewing is critical, position the LED

mark on the base in the intended direction (Refer to Figure

8).

3. Make connections directly to the audible base terminals

located on the back of the base. Refer to the related

Installation/Wiring diagram.

4. After all bases are installed, check loop continuity. For

ABHW-4BZ loop continuity check, refer to the DPU or

SDPU Manual, “Testing a FireFinder-XLS”.

5. If loop continuity is acceptable, proceed with detector head

installation.

etector

placement

Even though no specific spacing are allocated to the detectors

used with this base, use 30 foot center spacing (900 sq ft), as

referred to in NFPA Standard 72 National Fire Alarm Code

and CAN/ULC-S524, as a guide or starting point, if practical,

in a detector installation layout. This spacing is based on ideal

conditions—smooth ceiling, no air movement, and no physical

obstructions. In all installations (except in special

circumstances like computer room under floors), locate the

detector on the ceiling, a minimum of 6 inches from a side

wall, or on a wall, between 4 and 6 inches from the ceiling.

If questions arise regarding detector placement, it is extremely

important that the drawings provided or approved by Siemens

Industry, Inc., or by its authorized distributors be followed! The

detector placements shown on these drawings were chosen

after a careful evaluation of all facets of protecting the area.

Environmental factors such as air current, temperature,

humidity, air pressure, and the nature of the fire load are

carefully considered. Special consideration is given to room or

area configuration and the type of ceiling (sloped or

flat, smooth

or beamed). Siemens Industry, Inc.'s extensive experience in

the design of fire detection systems assures optimum detector

placement and is reflected in these drawings. Follow sound

engineering judgment made by qualified personnel.

Compatible fire alarm control panels:

Model

System Type

Doc. P/N

(See Page 10 Note 1)

FireFinder® XLS FACP

315-034242

FC2005

Desigo™ Fire Safety 50-point panel

A6V10333722

FC901

Cerberus™ PRO 50-point FACP

A6V10336754

FC2025 / FC2050 /

FV2025 / FV2050

Desigo 250 & 500 point Fire Alarm Control Panels

A6V10337045

FC922 / FC924 / FV922 /

FV924

Cerberus PRO 250 & 500 point Fire Alarm Control Panels

A6V10356958

Compatible detectors:

FD-UL series detectors (table 1):

Model

Siemens Part #

Doc. P/N

Type / Description

FDO421

S54320-F4-A1

A6V10323926

Desigo optical detector

FDOT421

S54320-F6-A1

A6V10323934

Desigo optical / heat detector

FDT421

S54320-F5-A1

A6V10323930

Desigo heat detector

FDOOT441

S54320-F7-A1

A6V10324655

Desigo dual optical heat detector

FDOOTC441

S54320-F8-A1

A6V10324657

Desigo dual optical heat & CO detector

OOH941

S54320-F7-A2

A6V10324659

Cerberus PRO dual optical heat detector

OOHC941

S54320-F8-A2

A6V10324661

Cerberus PRO dual optical heat & CO detector

OP921

S54320-F4-A2

A6V10323928

Cerberus PRO optical detector

OH921

S54320-F6-A2

A6V10323936

Cerberus PRO optical / heat detector

HI921

S54320-F5-A2

A6V10323932

Cerberus PRO heat detector

H-series detectors (table 2):

Model

Siemens Part #

Doc. P/N

Type / Description

HFP-11

500-033290

315-033290

H-Series optical / heat detector

HFPT-11

500-033380

315-033290

H-Series heat detector

HFPO-11

500-034800

315-034800

H-Series optical detector

SFP-11

500-033290C

315-033290C

Canada H-Series optical / heat detector

SFPT-11

500-033380C

315-033290C

Canada H-Series heat detector

SFPO-11

500-034800C

315-033290C

Canada H-Series optical detector

Compatible remote lamps (table 3):

Model

Siemens Part #

Doc. P/N

Type / Description

RL-HW

500-033310

315-033230

Remote alarm lamp (wall)

RL-HC

500-033230

315-033230

Remote alarm lamp (ceiling)

Note:

1. RPR-1 remote relay and HTRI are used for 24VDC power supervision. 24VDC wire open will

cause trouble reported by HTRI. Refer to Installation Instruction of RPR-1 (315-096055).

2. ABHW-4BZ terminals 5-6 are polarity insensitive. Line 1 and Line 2 can be either line of

device loop.

3. EOL device of HTRI: 3.6K, 1/4W resistor, P/N 140-820185.

4. ABHW-4BZ can be wired either Style Z (Class A) or Style Y (Class B).

5. For the max load current, refer to the specifications of the compatible panels listed in this

document.

6. The 24VDC regulated power supply could be the Aux Power Output from the compatible

panels, or from PAD-3/PAD-4/PAD-5, or other UL listed 24VDC regulated power supply. 24V

FWR power supply can't be allowed.

Figure 1

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by 24V

Regulated Power Supply

ABHW-4BZ ABHW-4BZ

Note:

1. Polarity shown in active state at terminals 1 and 2 of ABHW-4BZ and 1-4 of ZIC-4A. Proper

polarity must be maintained or audible base will not operate properly. Each audible base must

be tested to verify operation.

2. Tone selection (refer to page 10 NOTE 4 for more information).

3. ABHW-4BZ terminals 5-6 are polarity insensitive. Line 1 and Line 2 can be either line of the

loop.

4. ABHW-4BZ shown Style Z (Class A). It may also be wired as Style Y (Class B).

5. ZIC-4A Notification Appliance Circuits provide 4 outputs that can be configured for Class A. or

Class B. Refer to the ZIC-4A Installation Instructions, P/N 315-033050.

6. EOL resistor, 24k ohms, 1/2 watt, 5%, P/N 140-820405.

Figure 2

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by ZIC-4A

(NAC of FireFinder-XLS System)

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

ZONE 3

ZONE 2

ZONE 4

ZIC-4A

ABHW-4BZ ABHW-4BZ

61b

8 8

7 7

6 6

5 5

1 12 2

3 3

4 4

TO NEXT

ADDRESSABLE

DEVICE

LINE 2

LINE 1

LINE 2

24K

1/2W

FROM DLC LOOP OF

FIREFINDER-XLS

SYSTEM

NOTE 2

SEE 3 SEE 3

Note:

1. The NAC circuit shown in the diagram is the active state at terminal 1 and 2 of ABHW-4BZ.

2. ABHW-4BZ terminals 5-6 are polarity insensitive. Line 1 and Line 2 can be either line of

device loop.

3. The wiring at NAC of PAD-3/PAD-4/PAD-5 shown in the diagram for ABHW-4BZ is Style Z

(Class A)(No EOL needed). If Style Y (Class B) wiring used at NAC output, EOL (24K, 0.5W

resistor) must be used.

4. For the max load current and max cable resistance, refer to the specifications of PAD-

3/PAD-4/PAD-5, P/N: 315-099082/315-050217/A6V101030358.

Figure 3

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by NAC of

PAD-3/PAD-4/PAD-5 system

Note:

1. The NAC circuit shown in the diagram is the active state at terminal 1 and 2 of ABHW-4BZ.

2. ABHW-4BZ terminals 5-6 are polarity insensitive. Line 1 and Line 2 can be either line of

device loop.

3. The wiring at NAC of FC2005/FC901 shown in the diagram for ABHW-4BZ is Style Z (Class

A) (no EOL needed). If Style Y (Class B) wiring used at NAC output, EOL (24K, 0.5W

resistor) must be used.

4. For the max load current and max cable resistance, refer to the specifications of FC2005/FC901.

Figure 4.1

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by NAC of

FC2005/FC901

ABHW-4BZ ABHW-4BZ

61b

8 8

7 7

6 6

5 5

1 12 2

3 3

4 4

TO NEXT

ADDRESSABLE

DEVICE

LINE 1

LINE 2

LINE 1

FROM THE DEVICE LINE OF

THE COMPATIBLE LISTED

IN THE SPECIFICATION

NAC1

NAC1 NAC2

NAC2 NAC3

NAC3 NAC4

NAC4

NAC outputs of PAD-3/

PAD-4/PAD-5

ABHW-4BZ ABHW-4BZ

61b

8 8

7 7

6 6

5 5

1 12 2

3 3

4 4

TO NEXT

ADDRESSABLE

DEVICE

LINE 1

LINE 2

LINE 1

FROM THE DEVICE LINE OF

THE COMPATIBLE LISTED

IN THE SPECIFICATION

N_AN N_AP N_BN N_BP

NAC outputs of

F 2005 / FC901C

Note:

1. The NAC circuit shown in the diagram is the active state at terminal 1 and 2 of ABHW-4BZ.

2. ABHW-4BZ terminals 5-6 are polarity insensitive. Line 1 and Line 2 can be either line of

device loop.

3. The wiring at NAC of FC2025/FC2050/FV2025/FV2050 and FC922/FC924/FV922/FV924

shown in the diagram for ABHW-4BZ is Style Z (Class A) (no EOL needed). If Style Y (Class

B) wiring used at NAC output, EOL (2.4K, 0.5W resistor) must be used.

4. For the max load current and max cable resistance, refer to the specifications of FC2025/FC2050

/FV2025/FV2050 and FC922/FC924/FV922/FV924.

Figure 4.2

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by NAC of

FC2025/FC2050/FV2025/FV2050 and FC922/FC924/FV922/FV924

Figure 5

Installation/Wiring Diagram for ABHW-4BZ Audible Base Powered by Device

Loop

ABHW-4BZ ABHW-4BZ

61b

8 8

7 7

6 6

5 5

1 12 2

3 3

4 4

TO NEXT

ADDRESSABLE

DEVICE

LINE 1

LINE 2

LINE 1

FROM THE DEVICE LINE OF

THE COMPATIBLE LISTED

IN THE SPECIFICATION

NAC1

2_- NAC1

2_+ NAC1

1_- NAC1

1_+

per Periphery

NAC outputs

ABHW-4BZ ABHW-4BZ

61b

8 8

7 7

6 6

5 5

1 12 2

3 3

4 4

LINE 1

LINE 2

FROM DLC LOOP OF

FIREFINDER-XLS SYSTEM

FC2005/FC901 SYSTEM

FC2025/FC2050/FV2025/FV2050 SYSTEM

SYSTEMFC922/FC924/FV922/FV924

61b

Figure 6

ABHW-4BZ Audible Base Terminal Blocks (only for HFP-11, HFPT-11,

HFPO-11, SFP-11, SFPT-11 and SFPO-11 detectors)

Note:

The ABHW-4BZ terminal 3 should be connected to RL-HC/RL-HW TB1

The ABHW-4BZ terminal 4 should be connected to RL-HC/RL-HW TB2 or TB3

Figure7

ABHW-4BZ Audible Base Terminal Blocks (only for FDO421, FDOT421,

FDT421, FDOOT441, FDOOTC441, OP921, OH921, HI921, OOH941 and

OOHC941 detectors.)

8765

TO NEXTABHW-4BZ, DB-11,

DB-3S or DB-X3RS

LINE 1 LINE 2

FROM DLC LOOP OF

FIREFINDER-XLS SYSTEM

F 2005 / F 901 SYSTEM

FC2025/FC2050/FV2025/FV2050

FC922/FC924/FV922/FV924

C C

SYSTEM

JUMPER FOR

TONE SELECTION ABHW-4BZ

TO NEXTABHW-4BZ, DB-11,

DB-3S or DB-X3RS

LINE 1 LINE 2

FROM DLC LOOP OF

FIREFINDER-XLS SYSTEM

FC2005 / FC901 SYSTEM

FC2025/FC2050/FV2025/FV2050

FC922/FC924/FV922/FV924

SYSTEM

TB1TB3

TB2

RLH

REMOTE LAMP

See table 3

ABHW-4BZ

Andere Siemens Messgerät Handbücher

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

Siemens

Siemens Sitrans LR250 Bedienungsanleitung

Siemens

Siemens SD 270 Bedienungsanleitung

Siemens

Siemens UH50 Series Bedienungsanleitung

Siemens

Siemens SITRANS F US Series Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 1100 Bedienungsanleitung

Siemens

Siemens Milltronics C-40 Bedienungsanleitung

Siemens

Siemens SITRANS MAG 5100W Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SICAM Q80 Bedienungsanleitung

Siemens

Siemens ULTRAMAT 23 Bedienungsanleitung

Siemens

Siemens FS720 Series Betriebsanleitung

Siemens

Siemens Pointek CLS200 Bedienungsanleitung

Siemens

Siemens SIPROCESS GA700 Administratorhandbuch

Siemens

Siemens 3NP11 3 Series Bedienungsanleitung

Siemens

Siemens SITRANS F Betriebsanleitung

Siemens

Siemens 5SV8001-6KK Bedienungsanleitung

Siemens

Siemens SENTRON PAC4200 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens SITRANS FC410 Bedienungsanleitung

Siemens

Siemens SICAM P37 Bedienungsanleitung

Siemens

Siemens pointek CLS 100 Bedienungsanleitung

Siemens

Siemens SENTRON PAC3200T Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung