Siemens Sitrans F Series Bedienungsanleitung

Operating Instructions

SITRANS F

Coriolis Flowmeters

MASS 6000 Ex d transmitter

Answers for industry.

08/2015

Edition

s

Coriolis owmeters

MASS 6000 Ex d transmitter

Operating Instructions

These Operating Instructions apply to Siemens

products SITRANS MASS 6000 Ex d with order code

commencing 7ME4110-2G, 7ME4110-2H,

7ME4110-2J.

For use with sensor type MASS 2100 or FC300.

08/2015

A5E02944883-AA

SITRANS F

Contents 1. Introduction................................................................................................................. 4

2. Installation................................................................................................................... 5

2.1 Compact .....................................................................................................................6

2.2 Remote ........................................................................................................................ 6

2.3 Ex survey according to Directive 94/9/EC (ATEX)............................................................ 6

2.4 Overview ..................................................................................................................... 7

2.5 Deviceidentication.....................................................................................................8

2.6 Approvals..................................................................................................................... 9

2.7 Special conditions for safe use of MASS 6000 Ex-d version and MASS 2100 ................... 9

2.8 Mounting of transmitter compact or remote ............................................................... 10

2.9 Display and keypad.....................................................................................................10

3. Electrical connection .................................................................................................. 11

3.1 Electrical connection compact or remote ....................................................................11

3.2 Setting of active or passive current out-put mode ....................................................... 13

3.3 SENSORPROMunit.................................................................................................... 13

3.4 Installation of add-on module (AOM).......................................................................... 14

3.5 Installation examples .................................................................................................15

4. Technical data............................................................................................................16

4.1 Transmitter MASS 6000 Ex-d ...................................................................................... 17

4.2 Output characteristic MASS 6000 Ex-d........................................................................19

5. Commissioning ..........................................................................................................20

5.1 Keypad and display layout .......................................................................................... 20

5.2 Menu build-up ........................................................................................................... 21

5.2.1 Password ................................................................................................................... 21

5.3 Menu overview ..........................................................................................................22

5.4 Menu details ..............................................................................................................23

5.5 Outputs setting menu ................................................................................................24

5.6 Reset mode................................................................................................................ 26

6. Service....................................................................................................................... 27

6.1 List of error numbers.................................................................................................. 27

6.2 Trouble shooting MASS 6000 Ex-d ..............................................................................28

7. Ordering ....................................................................................................................29

7.1 Transmitter MASS 6000 Ex-d for remote mounting......................................................29

7.2 Spare parts for MASS 6000 Ex-d and MASS 2100.........................................................29

3A5E36849425-AA

SITRANS F C MASSFLO

A5E02944883-AA

1. Introduction For safety reasons it is important that the following points, especially the points marked with a

warning sign, are read and understood before the system is being installed:

•Installation, connection, commissioning and service must be carried out by personnel who

arequaliedandauthorizedtodoso.

•It is very important that the same people have read and understand the instructions and

directions provided in this manual and that they follow the instructions and directions

before taking the equipment into use!

• Peoplewhoareauthorizedandtrainedbytheowneroftheequipmentmayoperatethe

equipment.

•The installation must ensure that the measuring system is correctly connected and is in

accordance with the connection diagram. The transmitter has to be earthed unless the power

supply is galvanically isolated.

•The mains protective earth wire must be connected to the PE terminal in accordance with

the diagram.

•In applications with working pressures/media that can be dangerous to people, surroundings,

equipment or others in case of pipe fracture, we recommend that special precautions such as

special placement, shielding or installation of a security guard or a security valve should be

made when the sensor is being installed.

• ItisrequiredthatthespecialdirectionsprovidedinthemanualandintheExcerticatemust

be followed!

•Installation of the equipment must comply with national regulations.

Example EN 60079-14 for Denmark.

•Repair and service can be done by approved Siemens Flow Instruments personnel only.

•The p/T ratings indicate the relationship between the maximum allowable pressure PS and

the maximum allowable temperature.

1. Introduction

SITRANS F C MASSFLO

A5E02944883-AA

Mount the sensor on a vibration-free wall or

steel frame as shown.

Ensure that the sensor is not emptied of liquid

(during normal operation) otherwise incorrect

measurement will occur.

With low flow, horizontal mounting is

recommended, in this position air bubbles

are easier to remove.

Locate the sensor low in the system in order to

avoid an under-pressure in the sensor sepera-

ting air/gas in the liquid.

If the liquid is volatile or contains solid

particles, vertical mounting is not recom-

mended.

Alwayslocatetheowmeterasfarawayas

possible from components that generate

mechanical vibration in the piping.

Cross talk between sensors mounted close to

each other may disturb the measurement. To

avoid cross talk never mount more than one

sensoroneachframeandmountexiblehose

connections between the sensors as shown.

2. Installation

Vertical mounting

Vibration

Cross talk

2. Installation

Tofacilitiatezero-pointadjustment,avalve

with tight shut-off should always be mount-

ed in connection with the sensor as a proper

zero-pointsettingisessentialforagood

accuarcy.

Note

Please read and follow the directions stated in

the instruction SFIDK.PI.028.P1.52 regarding

build-in of sensor.

The instruction is supplied with the sensor.

Zero-point adjustment

Horizontal mounting

Category 2 equipment

Maybeinstalledinzone1andzone2.

Category 1 equipment

SensorMASS2100maybeinstalledinzone0,

zone1andzone2.

Catetory 2 equipment

Transmitter MASS 6000 Ex-d may only be

installedinzone1andzone2.

2.1 Compact

2.2 Remote

SITRANS F C MASSFLO

A5E02944883-AA

2. Installation

2.3 Ex survey according

to Directive 94/9/EC

(ATEX)

Applies to instruments used in underground mining

operations, as well as their above ground operations,

which can be endangered by mine gas and/or

flammable dusts.

Instrument groups

Applies to instruments used in the remaining areas

which can be endangered by a potentially explosive

atmosphere.

Instruments of this category are for use in areas

where ignitable atmospheres caused, by a mixture

of air and gasses, vapours or mists or by dust/

air mixtures, can exist all of the time or for long

periods of time or else frequently.

Instruments of this category are for use in areas

where ignitable atmospheres caused, by a mixture

of air and gasses, vapours or mists or by dust/air

mixtures, can exist some of the time.

Instruments of this category are for use in areas

where ignitable atmospheres caused, by a mixture

of air and gasses, vapours or mists or by dust/air

mixtures, are not likely to exist. However, if they

do occur then in all probability, only seldom or for

short periods of time.

Instrument category

(TheguresinbracketsrefertoIEC)

Explosion protected electrial equipment = Ex

Ex protection labelling in square brackets refers to "Associated electrical equipment"

as an example: II 2G Ex ia IIC T5

Type of protection

o Oil encapsulated i Intrinsic safety (ia, ib)

p Pressurizedapparatus n Non-incentiveequipment

q Powderlling m Encapsulation

d Flameproof enclosure s Special protection

e Increased safety

Explosion groups

Gases and vapours Minimum EN/

(examples) ignition IEC

energy [mJ]

•Ammonia - IIA

• Acetone,aircraftfuel,benzine,   

crude oil, diesel oil, ethane, ethanoic

acid, ether, gasolines, heating oil,

hexane, methane, propane 0.18 IIA

•Ethylene, isoprene, town gas 0.06 IIB

•Acetylene, carbon disulphide,

hydrogen 0.02 IIC

Ignition temperature

Maximum surface temperature EN / IEC

450°C 842°F T1

300°C 572°F T2

200°C 392°F T3

135°C 275°F T4

100°C 212°F T5

EN 50014 Directive 94/9/EC (ATEX)

Denition

(0)

Labelling

with gases

Labelling

with dusts

(20)

(1)

(21)

(2)

(22)

SITRANS F C MASSFLO

A5E02944883-AA

2. Installation

2.4 Overview A = Ex e (Increased safety)

B = Ex ia (Intrinsic safety)

C = Ex d (Flameproof safety)

MASS 6000 Ex-d

Flameproof enlosure

Ex d e ib [ia Ga] IIC T4 Gb

1. M20x1.5, black ATEX approved glands,

power supply cable.

2. Earthing terminal, connect to potential

equializingcoils(PEC).

3. M20x1.5, blue ATEX approved glands,

output and input cable.

4. Multi-plug connection to sensor Ex ia.

5. Display with push buttons.

MASS 2100

Intrinsic safety

Ex ia IIC T3...T5

1 Sensor multi-plug connection Ex ia.

MASS 6000 Ex-d and

MASS 2100 compact

Ex d e ib [ia Ga] IIC T4 Gb

SITRANS F C MASSFLO

A5E02944883-AA

2. Installation

2.5 Device identication

Transmitter

MASS 6000 Ex-d label

No. Meaning

 1. NotiedbodyforQAsupervision:ULInternationalDEMKOA/S,Denmark

2. Explosion protected

3. ATEX Equipment Group and Protection Category

4. EC Approval Numbers and Protection Type

5. Interface data

6. Production date

Example: 013302N14 3

Week 14 Year 2003

7. Warning,donotopentheEx-denclosurewhenenergized

8. Ambient temperature range

SITRANS F C MASS 6000 Exd

Rated Voltage : 24V AC/DC 50-60Hz

0539

DEMKO 03 ATEX 135253X

Warning -

Serial No. : XXXXXXNXXX

User Tag No. : XXXXXXXX

Code No. : 7ME4110-1FA21-1AA0

II 2 G

Made in France

83H42.12.10

Siemens A/S Flow Instruments, 6400 Soenderborg, Denmark

SEE MANUAL FOR

TECHNICAL DATA / INTERFACE DATA

Ex d e ib [ia Ga] IIC T4 Gb

Intrinsic safety specification:

Do not open when energized

After de-energizing, wait 30 minutes before opening

Tamb. : -20º to +50° C

IP67 / NEMA 6

Rated Power : 6VA

SITRANS F C MASSFLO

A5E02944883-AA

2.6 Approvals

2.7 Special conditions

for safe use of

MASS 6000 Ex-d

sensor

•For installations in which both the Ci and Li of the intrinsically safe apparatus exceeds1% of

the Co and Lo parameters of the MASS 6000 (excluding the cable), then 50% ofCo and Lo

parameters are applicable and shall not be exceeded. The reduced capacitanceshall not be

greater than 1 μF for Groups IIB and IIA, and 600 nF for Group IIC.

•If the sensor, to which MASS 6000 is connected, measures liquids with temperatureabove

50 °C (122 °F), the MASS 6000 must be thermally insulated or separately installed.

•The 24 V supply voltage shall be from a safety-isolated transformer according to EN 60742

orEN61558-1.Thepowersupplycablewiresize0.2-2.5mm2/ 24-14 AWG.

•All the wiring for increased safety shall be in the separate section of the terminal compart-

ment and shall be covered with the plastic cover. The cover is marked with "Increased

Safety".

•The transmittershall always be connected to PE (earth ground) using the internalterminal or

the external PE (earth ground).

•The equipment shall either be installed in an area where there is a low risk of mechanical

damage or, if this not possible, the window shall be protected with an additional guard that

provides it with mechanical protection adequate for the application.

•The equipment must be protected against direct sunlight and other ultraviolet light sources.

Directives

2. Installation

Transmitter MASS 6000 Ex-d compact or remote mounted

0539 II 2 G

DEMKO 03 ATEX 135253X

Ex d e ib [ia Ga] IIC T4 Gb

ambient temperature −20 to +50°C/−4°F to 122°F

EN 60079-0:2012+A11:2013

EN 60079-1:2007

EN 60079-7:2007

EN 60079-11:2012

EN 60079-25:2010

Andere Handbücher für Sitrans F Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Messgerät Handbücher

Siemens

Siemens SITRANS P300 Bedienungsanleitung

Siemens

Siemens SIRIUS Merkblatt

Siemens

Siemens SENTRON 5TT7 Benutzerhandbuch

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens Synova FC330A Bedienungsanleitung

Siemens

Siemens SITRANS F US SONOFLO SONOKIT Bedienungsanleitung

Siemens

Siemens SENTRON PAC4220 Bedienungsanleitung

Siemens

Siemens SITRANS MAG 1100 F Bedienungsanleitung

Siemens

Siemens SITRANS F MAG 6000 I Bedienungsanleitung

Siemens

Siemens Synco 700 RMZ785 Bedienerhandbuch

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens SITRANS F US Bedienungsanleitung

Siemens

Siemens 7ME30 Bedienungsanleitung

Siemens

Siemens SITRANS F FCS400 Bedienungsanleitung

Siemens

Siemens Synco 700 Series Bedienungsanleitung

Siemens

Siemens FIDAMAT 6 Bedienungsanleitung

Siemens

Siemens FC700A Montageanleitung

Siemens

Siemens Sitrans LR250 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 DI 6 Bedienungsanleitung

Siemens

Siemens LDS 6 Bedienungsanleitung

Siemens

Siemens SITRANS FC410 Kurzanleitung

Siemens

Siemens 7LQ3 350 Bedienungsanleitung

Siemens

Siemens SIWAREX WL230 BB-S SA Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung