Siemens SITRANS F Bedienungsanleitung

A5E33120231-001, 12/2013 1

SITRANS F

Coriolis Flowmeters

SITRANS FC410 flowmeter

Quick Start

Before installing, including in hazardous areas, refer to the Operating Instructions on the internet or on the SITRANS F

documentation CD-ROM which is included in the product package. They contain detailed safety regulations, information and

specifications which must be observed when installing. Documentation and approvals can be found on the internet:

Flow documentation (http://www.siemens.com/flowdocumentation)

CAUTION

Proper handling

Correct, reliable operation of the device requires proper transport, storage, positioning and assembly. The device must be

carefully operated and maintained. Only qualified personnel should install or operate this device.

Items supplied

With M12 plug connection

●SITRANS FC410 flowmeter

●Sensor cable with M12 connector

●SD card with production certificates

●Quick Start guide

●CD containing software, certificates and device

manuals

With sensor terminal housing

●SITRANS FC410 flowmeter

●Sensor cable

●Packet of cable glands

●SD card with production certificates

●Quick Start guide

●CD containing software, certificates and device

manuals

Note

Supplementary information

Supplementary product and production specific certificates are included on the SensorFlash® SD card.

Note

Scope of delivery may vary, depending on version and add-ons. Make sure the scope of delivery and the information on the

nameplate correspond to your order and the delivery note.

How to install

SITRANS FC410 flowmeter

2A5E33120231-001, 12/2013

Flowmeter overview

①

Mini Flow Link (MFL)

②

Lid-lock

③

Cable feed-through (M12 socket or gland)

④

Plug and threaded port for e.g. pressure guard

⑤

Sensor enclosure

⑥

Process connections

Installing/mounting

Location in the system

The optimum location in the system depends on the application:

●Liquid applications

Gas or vapor bubbles in the fluid may result in erroneous measurements, particularly in the density measurement.

–Do not install the flowmeter at the highest point in the system, where bubbles will be trapped.

–Install the flowmeter in low pipeline sections, at the bottom of a U-section in the pipeline.

Figure 3-1 Liquid applications, wrong location with trapped air/gas

●Gas applications

Vapor condensation or oil traces in the gas may result in erroneous measurements.

–Do not install the flowmeter at the lowest point of the system.

–Install a filter.

Figure 3-2 Gas applications, wrong location with trapped oil

Flow direction

The calibrated flow direction is indicated by the arrow on the sensor. Flow in this direction will be indicated as positive by

default. The sensitivity and the accuracy of the sensor do not change with reverse flow.

The indicated flow direction (positive/negative) is configurable.

SITRANS FC410 flowmeter

A5E33120231-001, 12/2013 3

CAUTION

Accurate measurement

The sensor must always be completely filled with process media in order to measure accurately.

Orienting the sensor

The sensor operates in any orientation. The optimal orientation depends on the process fluid and the process conditions.

Siemens recommends orienting the sensor in one of the following ways:

1. Vertical installation with an upwards flow (self-draining)

Figure 3-3 Vertical orientation, upwards flow

2. Horizontal installation, tubes down (recommended for liquid applications)

Figure 3-4 Horizontal orientation, tubes down

3. Horizontal installation, tubes up (recommended for gas applications)

Figure 3-5 Horizontal orientation; tubes up

SITRANS FC410 flowmeter

4A5E33120231-001, 12/2013

Note

Hygienic applications

In 3A and EHEDG certified hygienic applications the flowmeter must be installed vertically as shown in 1 above.

Installation in a drop line

Installation in a drop line is only recommended if a pipeline reduction or orifice with a smaller cross-section can be installed

to create back-pressure and prevent the sensor from being partially drained while measuring.

①

Back pressure orifice

②

On / off valve

Figure 3-6 Installation in drop line

Mounting the device

NOTICE

Incorrect mounting

The device can be damaged, destroyed or its functionality impaired through improper mounting.

●Before installing ensure there is no visible damage present on the device.

●Make sure that process connectors are clean, and suitable gaskets and glands are used.

●Mount the device using suitable tools.

WARNING

Unsuitable connecting parts

Danger of injury or poisoning.

In case of improper mounting hot, toxic and corrosive process media could be released at the connections.

●Ensure that connecting parts (such as flange gaskets and bolts) are suitable for connection and process media.

●Install the sensor in well-supported pipelines in order to support the weight of the flowmeter.

●Center the connecting pipelines axially in order to assure a stress-free installation. The flowmeter must not be used to

bring the rest of the pipework into line; make sure the pipework is correctly aligned before inserting the flow sensor.

SITRANS FC410 flowmeter

A5E33120231-001, 12/2013 5

●Install two supports or hangers symmetrically and stress-free on the pipeline in close proximity to the process

connections.

Note

Handling

Never lift the flowmeter using the housing, that is always lift the sensor body.

Avoid vibrations

●Make sure that any valves or pumps upstream of the sensor do not cavitate and do not send vibrations into the sensor.

●Decouple vibrating pipeline from the flow sensor using flexible tube or couplings.

Figure 3-7 Non-flexible pipes not recommended in vibrating environment

Figure 3-8 Flexible pipes recommended in vibrating environment

Avoid cross talk

If operating more than one flowmeter in one or multiple interconnected pipelines there is a risk of cross talk.

Prevent cross talk in one of the following ways:

●Mount sensors on separate frames

●Decouple the pipeline using flexible tube or couplings

Figure 3-9 High risk of cross talk when using non-flexible pipes

Figure 3-10 Low risk of cross talk when using flexible pipes and separate frames

SITRANS FC410 flowmeter

6A5E33120231-001, 12/2013

Connecting

Note

End Of Line (EOL) termination

The FC410 EOL termination DIP switch is default set to EOL active. To change termination setting see Setting the EOL

termination DIP switches (Page 8).

M12 version

The sensor is provided with a preformed cable terminated with M12 style stainless steel weather-proof plugs.

The cable screen is physically and electrically terminated within the body of the plug.

Take care when handling the cable and passing it through cable ducting that the plug is not subjected to excessive tension

(pulling) as the internal connections may be disengaged.

Note

Never pull the cable by the plug - only by the cable itself.

1. Connect the sensor using the supplied 4-wire cable with M12 connectors.

Note

Grounding

The sensor cable screen is mechanically connected to the grounding terminal (PE), only when the M12 plug is correctly

tightened.

Terminal number

Description

Wire color (Siemens cable)

24 VDC

Orange

0 VDC

Yellow

White

Blue

Cable termination version

A: Prepare the cable by stripping it at both ends.

Figure 4-1 Cable end

B: Connect wires within the sensor terminal space

1. Remove the lock screw and remove the lid.

2. Undo the flexible strap.

3. Disconnect the sensor connection (white plug) from the electronic.

4. Loosen the mounting screw using a TX10 Torx driver and remove the electronic from the housing.

5. Remove the cap and the ferrule from the cable gland and slide onto the cable.

6. Push the cable through the open gland and anchor the cable shield and the wires with the clamp bar.

7. Remove the terminal block from the electronic.

SITRANS FC410 flowmeter

A5E33120231-001, 12/2013 7

8. Connect the wires to the terminals according to the list below and the label on the DSL lid.

Terminal number

Description

Wire color (Siemens cable)

24 VDC

Orange

0 VDC

Yellow

White

Blue

Figure 4-2 Sensor terminal space

Figure 4-3 Terminal 2

1. Reinstall the electronic including the mounting screw.

2. Connect the sensor connection and the sensor cable.

3. Restore the flexible strap around all wires.

SITRANS FC410 flowmeter

8A5E33120231-001, 12/2013

Figure 4-4 Terminal 1

4. Assemble and tighten the cable gland.

5. Remove the O-ring from lid.

6. Reinstate the lid and screw in until the mechanical stop. Wind back the lid by one turn.

7. Mount the O-ring by pulling it over the lid and tighten the lid until you feel friction from the O-ring on both sides. Wind the

lid by one quarter of a turn to seal on the O-ring.

8. Reinstate and tighten the lid lock screw.

Setting the EOL termination DIP switches

It is important to terminate the Modbus RS 485 line correctly at the start and end of the bus segment since impedance

mismatch results in reflections on the line which can cause faulty communication transmission.

If the device is at the end of the bus segment, it is recommended to terminate the device as shown in Auto hotspot. The

table below shows the relation between the DIP switch settings and the permissible communication interface set-ups.

Default configuration is EOL active.

Location of DIP switch

The DIP switch is located in the electronic as shown below.

Figure 4-5 DIP switch location (all set to ON)

DIP switch settings for communication set-up

DIP switch

Communication set-up

Switch 1

Switch 2

Switch 3

Switch 4

EOL not active

Off

EOL active

NOTICE

Avoid DIP switch settings not mentioned in the table!

DIP switch settings not mentioned in the table above are not allowed and will cause a risk of reduction in communication

interface reliability.

SITRANS FC410 flowmeter

A5E33120231-001, 12/2013 9

System configurations

Non-hazardous locations

The following figures show examples of installations in point-to-point and multidrop configurations in non-hazardous

locations.

Figure 4-6 Point-to-point configuration in non-hazardous location

Figure 4-7 Multidrop configuration (branch) in non-hazardous location

SITRANS FC410 flowmeter

10 A5E33120231-001, 12/2013

Figure 4-8 Multidrop configuration (Daisy chain) in non-hazardous location

Hazardous locations

The following figures show examples of installations in point-to-point and multidrop configurations in hazardous locations.

Figure 4-9 Point-to-point configuration in hazardous location

Andere Handbücher für SITRANS F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Siemens Messgerät Handbücher

Siemens

Siemens CSI Host Driver Bedienungsanleitung

Siemens

Siemens SITRANS SCM IQ Bedienungsanleitung

Siemens

Siemens SENTRON PAC2200CLP Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SENTRON PAC2200 Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens Veeder-Root Driver Bedienungsanleitung

Siemens

Siemens Pointek CLS500 Bedienungsanleitung

Siemens

Siemens 5SV8000-6KK Bedienungsanleitung

Siemens

Siemens MMB3-ALD-UK Bedienungsanleitung

Siemens

Siemens 7KT1 543 Bedienungsanleitung

Siemens

Siemens SICAM Q200 7KG97 Bedienungsanleitung

Siemens

Siemens SEM3 Bedienungsanleitung

Siemens

Siemens SITRANS LR 400 Bedienungsanleitung

Siemens

Siemens SITRANS F Administratorhandbuch

Siemens

Siemens SIMATIC RTLS Series Bedienungsanleitung

Siemens

Siemens SITRANS FM100 Bedienungsanleitung

Siemens

Siemens SITRANS LG260 Bedienungsanleitung

Siemens

Siemens 5SV8001-6KK Bedienungsanleitung

Siemens

Siemens Cerberus CS1140 Bedienungsanleitung

Siemens

Siemens 5SV8 200-6KK Service-Handbuch

Siemens

Siemens SICAM Bedienungsanleitung

Siemens

Siemens SITRANS F FUE950 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung