Siemens PS-5N7 Bedienungsanleitung

P/N 315-092729-13

Fire Safety

OPERATION

The Model PS-5N7 from Siemens Building

Technologies, Inc. permits remote mounting

of the MXL annunciator modules MKB-1,

MKB-2,

and RCC-1/-1F. In addition, when the

PS-5N7

is used with a PIM-1, it provides an

interface for a remote printer that can be

supervised or unsupervised. Each PS-5N7

occupies one network node.

INSTALLATION

Mounting

The PS-5N7 can be used in an MME-3, MSE-2,

or an RCC-1/-1F enclosure. Mount the PS-5N7

in the following enclosures as described below

(See the Note at the top of page 2 if using a

PIM-1):

Figure 1

PS-5N7 Wiring Diagram in MME-3 or MSE-2 (Without a PIM-1)

1. MME-3—Install in the upper right-hand

corner (See Figure 1).

2. MSE-2—Install in the upper right-hand

corner (See Figure 1).

3. RCC-1/-1F—Install in the lower right-

hand corner (See Figure 2).

Note: In a special application which is

described on page 7, the PS-5N7

can be used as a source of

power in a remote extender

enclosure used to house extra

VSMs/VLMs/VFMs.

Installation Instructions

Model PS-5N7

Network Interface / 5V Power Supply

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Figure 2

PS-5N7 Wiring Diagram in the RCC-1/-1F Enclosure (Without a PIM-1)

Figure 3

PS-5N7 Wiring Diagram in MME-3 or MSE-2 (With a PIM-1)

Four male/female standoffs are provided in

each backbox in the correct location for

installing the PS-5N7. Place the PS-5N7

over the existing female standoffs. Fasten it,

using the threaded portion of the standoffs

as screws. Use the cable provided (See

Figures 1 and 2) to connect P1 on the

PS-5N7 to P1 on the ANN-1.

Note: If a PIM-1 is used in the config-

uration, refer to the instructions

below.

Using the PS-5N7 with a PIM-1

To support a remote printer, use a PIM-1

with the PS-5N7.

Note: The PIM-1 and PS-5N7 have the

same mounting holes.

When using a PIM-1 with the PS-5N7 in

an MME-3 or MSE-2 backbox (See Figure 3):

1. Mount the PIM-1 first, as shown.

2. Use the four male/female standoffs

provided with the PS-5N7 as screws.

3. Attach the PIM-1 to the female

standoffs.

4. Connect the cable from P1 of the

ANN-1 board to P1 on the PIM-1.

5. Next, mount the PS-5N7 on the same

standoffs, using the four screws from

the PIM-1 kit.

6. Attach the cable supplied with the

PIM to P2 on the PIM-1.

7. Plug the cable from P2 of the PIM-1

into P1 of the PS-5N7; see Figure 3.

Figure 4

PS-5N7 Cabling Diagram in the RCC-1/-1F Enclosure (With a PIM-1)

When using a PIM-1 Module with the

PS-5N7 in an RCC-1/-1F Enclosure (See

Figures 4 and 5):

1. Mount the PS-5N7 to the right of the

PIM-1 in the bottom of the enclosure.

2. Refer to the RCC-1/-1F Installation

Instructions, P/N 315-095364, for

instructions on the cabling connections.

For additional information refer to

the PIM-1 Instructions, P/N 315-091462.

Power Connection

The PS-5N7 requires a DC input of 14-31 VDC.

This input is available from the MMB or the

PSR-1. Refer to Figure 5 for the correct

wiring instructions.

Using the PS-5N7 with Style 4

(2-Wire) Network Connections

Use screw terminals 1 and 2 for Network A.

DO NOT USE wire terminals 3 and 4 in this

configuration. See Figure 5 for additional

wiring information. Refer to the PSR-1 Instal-

lation Instructions (P/N 315-090911) for more

details on Style 4 networks.

Using PS-5N7 with Style 7

(4- Wire) Network Connections

Do not place the PS-5N7 module in the last

position on a Style 7 Network. Use a NET-7

at each end of the network to provide proper

supervision.

Use screw terminals 1 and 2 for Network A,

terminals 3 and 4 for Network B. Refer to

Figure 5 for wiring instructions.

Wiring Restrictions

Network

The MXL supports a maximum of 64 network

nodes. Each module in the list below repre-

sents one node. Do not plan a system with

more than 64 of these modules.*

MMB (one allowed per system)

MOI-1 MOI-7

NET-4 NET-7

NET-7M PS-5N7

The total wire resistance in both wires of the

network pair cannot be more than 80 ohms.

*If the system has more than 32 nodes, an

REP-1 module must be used.

Notes:

1. Use a minimum wire gauge of 18 AWG.

2. Use a maximum of 80 ohms per pair of

wires for the network connections.

3. Use twisted pair or shielded twisted pair for

network connections.

4. Terminate the shield ONLY at the MMB

enclosure.

5. Eliminate all Network B wiring for Style 4.

Figure 5

PS-5N7 Power Supply and Network Wiring Diagram

24 VDC input:

14-31 VDC, 300mA max

5 VDC output:

5 VDC, 500mA max

Network:

8V P-P max, 150mA max

ELECTRICAL CONNECTIONS Refer to the following Installation

Instructions as needed:

MMB-2 P/N 315-095097

MMB-3 P/N 315-048860

PSR-1 P/N 315-090911

PS-35 P/N 315-085062

PLM-35 P/N 315-093495

PAD-3 P/N 315-099082

MXL/MXLV Manual P/N 315-092036

6. DO NOT place the PS-5N7 at the end of

the network (Style 7 only).

7. This configuration is power limited to NFPA

70 according to NEC 760.

8. Refer to Wiring Specification for MXL, MXL-

IQ and MXLV Systems, P/N 315-092772

revision 6 or higher, for additional wiring

information.

MMB

PSR-1

PLM-35

(Used with PS-35)

ALARMSAF

(Model BN4-002-UL)

PAD-3

TB5, 9-12

TB3, 3-6

TB1, 1-2

DC1

TB2, 18, 19

ELECTRICAL RATINGS*

24 VDC Power

You may connect multiple PS-5N7s to the

same 24V power supply as long as the total

line loss is within specified limits. Follow the

information given below to calculate the

allowable line losses.

CAUTION

Failure to follow these guidelines

may result in excessive voltage

drops that cause improper or no

operation of the system.

To determine the total line loss, and there-

fore, the maximum cable length permitted,

use the following values and limits.

Vmax—The maximum allowable voltage

loss due to wire resistance. Vmax must

not be more than 4V. (See Table 2.)

Imax—The total alarm current drawn by

all PS-5N7 modules connected to the 24

VDC supply. If a PIM-1 is used in the

system, include its current. (See the Imax

values for the approved power supplies

at the bottom of this column. See Table

1 also.)

Rmax—The value of wire resistance

that results in a 4 volt drop due to Imax.

To calculate the total line loss, use the fol-

lowing equation:

Rmax = Vmax ÷Imax

(Where Vmax = 4V in all cases)

The Rmax result obtained with this equation

is the total of all wire resistance in ohms in

the 24 VDC supply lines.

The following power supplies are compat-

ible with the PS-5N7. They are listed with

their maximum output current (Imax):

MMB 1 amp

PSR-1 2 amps

PLM-35 1.5 amps

ALARMSAF 4 amps

PAD-3 3 amps

The maximum module current is shown in

Table 1 below.

Table 1

Maximum Module Curren

Model Imax

PS-5N7 300mA

PIM-1 20mA

Once the wire resistance is calculated, use

Table 2 below to determine the maximum

allowable cable length. (See Figure 5.)

Table 2

Wire Resistance

AWG Ohms/1000

Feet

10 1

12 1.6

14 2.6

16 4.1

18 6.5

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm54

tnerruCeludoMCDV42ybdnatSAm54

ybnwardtnerrucynaedul

cnitonseoD* .7N5-SPehtybderewopsecivedroseludom

P/N 555-190967

Power Restrictions

(5V max current = 500mA)

Model No. 5V

Curren

OMM-1 0mA

OCC-1 22mA

ASC-1 29mA

ASC-2 29mA

ZC1-8B 31mA

ZC2-8B 31mA

ZC2-4AB 30mA

ZC3-4AB 28mA

ZCT-8B 33mA

Figure 6

PS-5N7 Connection to an OMM-1

CAUTION

Locate all equipment for this

configuration in the same

enclosure.

Refer to the following Installation

Instructions for further information:

PSR-1 P/N 315-090911

OMM-1 P/N 315-090267

Refer to Wiring Specification

for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772

revision 6 or higher, for

additional wiring information.

Using the PS-5N7 to Drive an OMM-1

In order to add Voice hardware to a remote

enclosure, use a PS-5N7 module to drive an

OMM-1 if the following conditions apply:

1. The remote enclosure is not

connected to the MMB, and

2. There are multiple MXLs that are not

networked.

Adding a PS-5N7 and an OMM-1 under

these conditions provides power as well as

communication with the MXLV. Refer to

Figure 6 for the correct wiring information

for this configuration.

To Use the PS-5N7 Module in a Remote Extender Enclosure:

Figure 7

Using the PS-5N7 in a Remote Extender Enclosure

ACM-1 P/N 315-092083

TBM-2 P/N 315-093782

VSM-1/VLM-1/VFM-1 P/N 315-092064

For additional information on this configuration,

refer to the following Installation Instructions:

Refer to Wiring Specification for MXL, MXL-IQ

and MXLV Systems, P/N 315-092772 revision 6

or higher, for additional wiring information.

P/N 315-092729-13

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Inhaltsverzeichnis

Andere Siemens Aufnahmegeräte Handbücher

Siemens

Siemens RUGGEDCOM RMC30 Bedienungsanleitung

Siemens

Siemens AS-i Master CM 1243-2 a Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens CM 1542-5 Bedienungsanleitung

Siemens

Siemens Netzteil 3 A Bedienungsanleitung

Siemens

Siemens TC35 Benutzerhandbuch

Siemens

Siemens Apogee P1 Bedienungsanleitung

Siemens

Siemens 538-735 Bedienungsanleitung

Siemens

Siemens ASM 456 Bedienungsanleitung

Siemens

Siemens Albatros2 RVA78.690 Bedienungsanleitung

Siemens

Siemens SITOP PSU6200 Gebrauchsanweisung

Siemens

Siemens CIM Bedienungsanleitung

Siemens

Siemens IM 152 Bedienungsanleitung

Siemens

Siemens NIC-C Bedienungsanleitung

Siemens

Siemens CERBETUS PYROTRONICS VDT Technisches Datenblatt

Siemens

Siemens SINAMICS V90 Bedienungsanleitung

Siemens

Siemens PMI-2 Bedienungsanleitung

Siemens

Siemens SIMOTION ADI4 Bedienungsanleitung

Siemens

Siemens Trunk Interface II Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET DP/AS-i Link 20E Bedienungsanleitung

Siemens

Siemens VIU-20 Bedienungsanleitung

Siemens

Siemens PMI Bedienungsanleitung

Siemens

Siemens XMI Bedienungsanleitung

Siemens

Siemens 2D-TZ577 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch