SIIG AV-GM03S3-S1 Bedienungsanleitung

VGA/component, Audio & RS-232 over CAT5

Extender with IR Pass-through

P/N: AV-GM03S3-S1

Safety and Notice

The AV-GM03S3-S1 VGA/component, Audio & RS-232 over CAT5 Extender with IR Pass-through

has been tested for conformance to safety regulations and requirements, and has been

certified for international use. However, like all electronic equipments, the AV-GM03S3-S1

should be used with care. Please read and follow the safety instructions to protect yourself

from possible injury and to minimize the risk of damage to the unit.

●Follow all instructions and warnings marked on this unit.

●Do not attempt to service this unit yourself, except where explained in this manual.

●Provide proper ventilation and air circulation and do not use near water.

●Keep objects that might damage the device and assure that the placement of this unit is on a

stable surface.

●Use only the power adapter and power cords and connection cables designed for this unit.

●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the

device before cleaning.

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................1

FEATURES...........................................................................................................................1

PACKAGE CONTENTS.........................................................................................................1

SPECIFICATIONS.................................................................................................................2

PANEL DESCRIPTIONS .......................................................................................................3

CONNECTION DIAGRAM....................................................................................................5

IR PASS-THROUGH.............................................................................................................6

SUPPORTED IR DATA FORMAT ..........................................................................................7

HARDWARE INSTALLATION ...............................................................................................8

PIN DEFINITION .................................................................................................................9

NOTICE.............................................................................................................................10

WARRANTY.......................................................................................................................11

INTRODUCTION

With only one cost effective Cat-5/5e/6 cable, the AV-GM03S3-S1 lets you extend VGA (WUXGA –

1920x1200@60) or 720p component video, bi-directional IR signals and RS-232 serial commands at

the same time to cover the distance up to 300m (1,000ft). The AV-GM03S3-S1 comes in a set of a

transmitter and a receiver. The transmitter AV-GM03S3-S1[Tx] is installed near the signal source

and has, and the receiver AV-GM03S3-S1[Rx] is placed near the desired display. With built-in EQ and

GAIN control, the transmission path can be adjusted to adapt the cable quality and video

bandwidth. In order to extend the control path, AV-GM03S3-S1 also built RS-232 half-duplex long

range extender along with VGA/component video signals.

FEATURES

Supports up to WUXGA [1920x1200@60] or UXGA [1600x1200@60] VGA signal to 300m

(1,000ft)

Supports 720p component video signal to 300m (1,000ft)

Supports RS-232 half-duplex & bi-directional IR pass-through

Supports analog stereo audio and digital S/PDIF stereo audio

Video and audio local out on transmitting unit for easy monitoring

Adjustable equalization and gain control on receiving unit for signal tuning

Wall mounting case & interlocked power jack for better fixedness

PACKAGE CONTENTS

1x AV-GM03S3-S1

2x 5V power supply unit

1~3x VGA-component breakout cable [optional accessory]

1x User Manual

SPECIFICATIONS

Model Name

AV-GM03S3-S1

Role of usage

Transmitter [TX]

Receiver [RX]

Video bandwidth

350MHz

Video support

VESA

Video Transmission

WUXGA [1920x1200] / 720p —300m (1,000ft) [CAT5e]

Audio support

Stereo

RS-232 signal type

Half-duplex

Input video signal

1.2 Volts [peak-to-peak]

Equalization

Continuous analog control

RGB delay control

Loop-out

1 VGA local-out + 1 audio local-out at TX

ESD protection

Human body model —±15kV [air-gap discharge] & ±8kV [contact

discharge]

Input

1x VGA

1x RS-232

2x 3.5mm

1x RCA

1x RS-232

1x 3.5mm

1xRJ-45

Output

1x RJ-45

1x VGA

2x 3.5mm

1x RCA

1x VGA

1x RS-232

1x RCA

1x 3.5mm

VGA connector

HD-15 [15-pin D-sub female]

RJ-45 connector

WE/SS 8P8C with 2 LED indicators

RS-232 connector

DE-9 [9-pin D-sub female]

RCA connector

S/PDIF digital audio

3.5mm connector

Earphone jack for analog stereo audio or IR cable

Mechanical

Housing

Metal enclosure

Dimensions

[L x W x H]

Model

[TX/RX] –123 x 95 x 25mm [4.8”x3.7”x1”]

Package

330 x 200 x 95mm [1’1”x7.9”x3.7”]

Carton

495 x 440 x 380mm [1’7.5”x1’5.3”x1’3”]

Weight

Model

[TX]–370g [12oz] / [RX]–380g [13oz]

Package

1240g [2.7 lbs]

Fixedness

Wall-mounting case with screws

Power supply

Inter-locked 5V 2A DC

Power consumption

6 Watts [max]

Operation temperature

0~40C [32~104F]

Storage temperature

-20~60C [-4~140F]

Relative humidity

20~90% RH [no condensation]

PANEL DESCRIPTIONS

Transmitting unit ►AV-GM03S3-S1-TX

Front Panel

1. RS-232: connect to a RS-232 signal source or receiver

2. IR-Blaster: connect to IR blaster for IR pass-through from RX to TX

3. Stereo IN: connect to analog audio source

4. S/PDIF IN: connect to digital audio source

5. Push-in button: select between S/PDIF and analog stereo audio [button down-S/PDIF, button

up-Stereo]

6. VGA IN: connect to a VGA input source or a component video source via a VGA-component break

cable

7. IR-Receiver: connect to IR receiver for IR pass-through from TX to RX

Rear Panel

8. +5V DC: inter-locked power jack to connect to 5V DC power supply unit

9. Local VGA: VGA loop-out to a local VGA display or component video display via a

VGA-component breakout cable

10. System OUT: Plug in a Cat-5/5e/6 cable that needs to be linked to the RJ-45 connector of the

receiving unit AV-GM03S3-S1[Rx]

11. Local S/PDIF: Digital stereo audio loop-out

12. Local Stereo: Analog stereo audio loop-out

Receiving unit►AV-GM03S3-S1-RX

Front Panel

13. RS-232: Connect to a RS-232 device

14. IR Receiver: Connect to the IR receiver

15. Audio OUT: Connect to analog audio output

16. S/PDIF OUT: Connect to digital audio output

17. VGA OUT: VGA output to a VGA display or component video display via a VGA-component

breakout cable

18. IR Blaster: Connect to the IR blaster

Rear Panel

19. +5V DC power jack: connect to 5V DC power supply

20. System IN:Plug in a CAT-5/5e/6 cable that needs to be linked to the RJ-45 connector of the

transmitting unit AV-GM03S3-S1[Tx]

21. EQUALIZER: Rotary control for equalization of R, G, B, respectively

22. GAIN: Rotary control for gain control of R, G, B, respectively respective R/G/B color channel

that is chosen by the RGB selector

Bottom Panel

DIP Switch Position

Description

Pin#1

Pin#2

Pin#3

Pin#4

ON []

OFF []

ON []

OFF []

TX&RX Extender Mode –

TxD1of AV-GM03S3-S1[TX] is connected to TxD of

AV-GM03S3-S1[RX]

RxD2of AV-GM03S3-S1[TX] is connected to RxD of

AV-GM03S3-S1[RX]

OFF []

ON []

OFF []

ON []

Master to Slave Mode –

TxD of AV-GM03S3-S1[TX] is connected to RxD of

AV-GM03S3-S1[RX]

RxD of AV-GM03S3-S1[TX] is connected to TxD of

AV-GM03S3-S1[RX]

CONNECTION DIAGRAM

1. TxD: The 3rd pin of RS-232, which is in charge of sending data

2. RxD: The 2nd pin of RS-232, which is in charge of receiving data

IR PASS-THROUGH

IR Extenders

IR Blaster IR Receiver

IR Sockets

AV-GM03S3-S1[Tx]

IR Blaster:Plug in an IR blaster here to emit all IR command signals received from the IR receiver on

AV-GM03S3-S1[Rx] to control the associated devices with built-in IR sensor

IR Receiver:Plug in an IR receiver here to receive all IR command signals from the IR remote controls

of the associated devices

AV-GM03S3-S1[Rx]

IR Blaster:Plug in an IR blaster here to emit all IR command signals received from the IR receiver on

AV-GM03S3-S1[Tx] to control the associated devices with built-in IR sensor

IR Receiver:Plug in an IR receiver here to receive all IR command signals from the IR remote control

of the IR source device.

Definition of IR Earphone Jack

IR Blaster

IR Receiver

SUPPORTED IR DATA FORMAT

Data Format

Suitable

Not Recommended

NEC



RC5



TOSHIBA MICOM CODE



GRUNDIG CODE



SONY 12 BIT CODE



SONY 15 BIT CODE



SONY 20 BIT CODE



RCA CODE



RCM CODE



MATSUSHITA CODE



MITSUBISHI CODE



ZENITH CODE



JVC CODE



M50560-001P



MN6125H



MN6125L



MN6014_C5D7



MN6014-C6D6



MC14457P



LC7464(AHEA)



GEMINI_CM



You can buy any IR extension cables in the market that are compatible to the definition of

the IR sockets for the matrix if necessary for replacement use. However, IR cables longer

than 2m (6-ft) may not work.

HARDWARE INSTALLATION

1. Connect your VGA source, audio source, infrared and RS-232 devices to the transmitting unit

AV-GM03S3-S1[Tx]. If you want to connect to a component video source, please find a

VGA-component breakout cable and link it between the video source and the transmitting unit

of AV-GM03S3-S1.

2. Connect your VGA display, audio speaker, infrared and RS-232 devices to the receiving unit

AV-GM03S3-S1[Rx]. If you want to connect to a component video display, please find a

VGA-component breakout cable and link it between the video display and the receiving unit of

AV-GM03S3-S1.

3. Connect a Cat-5/5e/6 cable between the transmitting and receiving units.

4. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.

5. Plug in 5V DC power supply unit to the power jack of the receiving unit AV-GM03S3-S1[Rx].

6. Plug in 5V DC power supply unit to the power jack of the transmitting unit AV-GM03S3-S1[Tx].

7. If you see the monitor is displaying blurred video or even worse, not displaying at all, please

adjust the EQ and Gain rotary controls to improve the cable skew. GAIN rotary control is to

adjust the gain to an appropriate level for a range of input signal levels (brightness), and EQ

rotary control is to equalize the wave form of the receiving video signal (sharpness). It is

suggested to begin with adjusting the rotary control of EQ to get the input video displayed first,

and then the rotary control of GAIN according to the video you see on the screen.

Inhaltsverzeichnis

Andere SIIG Extender Handbücher

SIIG

SIIG JU-EX0111-S1 Bedienungsanleitung

SIIG

SIIG CE-H20011-S1 Bedienungsanleitung

SIIG

SIIG CE-H22T11-S1 Bedienungsanleitung

SIIG

SIIG CE-H24911-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03W3-S1 Bedienungsanleitung

SIIG

SIIG CAT5e Bedienungsanleitung

SIIG

SIIG CE-H23811-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03T3-S1 Bedienungsanleitung

SIIG

SIIG CE-DP0511-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0403-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM04G3-S1 Bedienungsanleitung

SIIG

SIIG CE-HM0052-S1 Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04S3-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM0463-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0413-S1 Bedienungsanleitung

SIIG

SIIG CE-H23T11-S1 Bedienungsanleitung

SIIG

SIIG CE-D20012-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02P3-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02J3-S1 Bedienungsanleitung

SIIG

SIIG CE-H22811-S1 Bedienungsanleitung

SIIG

SIIG CE-VG0711-SA Bedienungsanleitung

SIIG

SIIG AV-GM02X3-S1 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung