SIIG CE-VG0711-SA Bedienungsanleitung

VGA&RS-232CAT5Extender

with RGB Delay Control

Quick Installation Guide

04-0586A

IntroducingtheVGA&RS-232CAT5Extender

TheVGA& RS-232CAT5e Extenderwith RGBDelay Control

extends VGA and RS-232 signals over 1 CAT5e/6 cable.

FeaturesandBenefits

• Extends VGA and RS-232 signals over one

economical CAT5/5e/6 cable with RGB delay

control

• VGA RGB delay control (de-skew) feature provides

compensation among R,G,B signals over long

transmission

• Supports RS-232 half-duplex

• Adjustable equalization and gain control

• Housing: metal (for better RF shielding)

PackageContents

•VGA& RS-232 CAT5Extender withRGB Delay Control

(one Tx & one Rx unit)

• 2 Power adapters (5V DC)

• Installation kit

• Quick installation guide

Layout

Transmitting Unit (Tx) Front View

Figure 1: Front view of Transmitting (Tx) unit

•RS-232:Connectstoa RS-232serial command device

•VGA In: Connects to a VGA input source

TransmittingUnit(Tx) Rear View

RS-232 VGA In

System Out

Power Jack Local VGA

Figure 2: Rear view of Transmitting (Tx) unit

•Power Jack:Connects to 5V DC power adapter

•Local VGA:Connects to a local VGA display

•System Out: Plug in a CAT5e/6 cable, link to the

System In of the receiving (Rx) unit

Figure 3: Front view of Receiving (Rx) unit

•RS-232:Connects toa RS-232 serialcommand device

•VGA Out: Connects to a remote VGA display

ReceivingUnit(Rx)RearView

RS-232 VGA Out

ReceivingUnit(Rx)FrontView

System InPower Jack Gain

RGB skew

adjust (-,+)

RGB

selector

Figure 4: Rear view of Receiving (Rx) unit

•Power Jack: Connects to 5V DC power adapter

•System In: Links to the CAT5e/6 cable from the

System Out of the transmitting (Tx) unit

•EQ: Rotary dial for adjusting signal sharpness

•Gain: Rotary dial for adjusting signal brightness

•RGBselector: Rotarydialfor selectingthe respective

R/G/B color for skew adjustment

•RGB skew adjust (-,+): Push button to decrease (-)

or increase (+) skew of the color channel (R/G/B)

chosen by the RGB selector rotary dial

DipSwitch(SerialMode)

The DIP switch is located on the bottom panel of the

receiving unit. See table below for description.

Notes: 1TxD: The 3rd pin of RS-232, which is in charge of

sending data; 2RxD: The 2nd pin of RS-232, which is in

charge of receiving data.

Hardware Installation

1. Power off all devices.

2. Connect your VGA and RS-232 source to the

transmitting unit.

3. Connect your display and RS-232 receiving device

to the receiving unit.

4. Connect your CAT-5/5e/6 LAN cable between the

transmitting and receiving units, make sure the

cable connection is tight and not loose.

5. Plug in the 5V DC power cord to the power jack of

transmitting and receiving units.

Dip Switch Position

Pin#1 Pin#2 Pin#3 Pin#4

Description

ON OFF ON OFF

OFF OFF

ON ON

Master to Slave mode -

TxD of transmitter to RxD of receiver

RxD or transmitter to TxD of receiver

Tx to Rx Extender Mode -

TxD1of transmitter to TxD of receiver

RxD2of transmitter to TxD or receiver

6. Power on all devices.

7. If your image is flickering or blinking, adjust the

Gain and EQ knobs to improve the cable skew. It is

suggested to begin by adjusting the EQ first then the

Gain according to the video displayed on the screen.

8. RGBskewadjustfeatureallowsskewcompensation

among red (R), green (G), and blue (B) signals due

to long transmission distance or low quality cabling.

Start by adjusting the RGB selector rotary dial to

choose R/G/B color channel, then use the -or +

RGB skew adjust push buttons to decrease or

increase,respectively,thedelayofthe corresponding

R/G/B color channel.

Notes

1. All transmission distances are measured using

Belden 1583A CAT5e 125MHz Solid UTP cable and

ASTRODESIGN Video Signal Generator VG-859C.

The transmission distance is defined as the distance

between the video source and the VGA display.

2. Transmisson length is affected by the type of CAT5/

6 cables, the type of VGA sources, and the type of

VGA display. Testing results show that solid UTP

cables (normally found in 300m [1000ft] bulk form)

can transmit longer distances than stranded UTP

cables. Shielded STP cables are better suited than

unshielded UTP cables. Solid UTP CAT5e cabling

returns longer tranmission distances than stranded

STP CAT6 cables. For longer transmission distance,

solid UTP/STP cables are your best choice.

3. To reduce the interference among the unshielded

twisted pairs of wires in the LAN cable, you can use

shielded LAN cables to reduce EMI problems.

4. For resolution greater than 1080i or 1280x1024, a

CAT6 cable is recommended.

5. Transmission distance depends on the

characteristics and quality of the cables. Higher

resolutions and longer transmission distances

require low skew cables (<25ns/100m) for best

performance. Unshielded CAT6 with metal RJ-45

connectors is recommended.

Technical Support and Warranty

QUESTIONS? SIIG’sOnline Support hasanswers! Simply visitour

web site at www.siig.com and click Support. Our online support

database is updated daily with new drivers and solutions. Answers

toyour questionscould bejust afew clicksaway. You can also submit

questions online and a technical support analysts will promptly

respond.

SIIGoffers a 3-year manufacturer warrantywith thisproduct. Please

see our web site for more warranty details. If you encounter any

problems with this product, please follow the procedures below.

A) If it is within the store's return policy period, please return the

product to the store where you purchased it.

B) Ifyour purchasehas passedthe store'sreturn policyperiod, please

follow these steps to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, click Support, then RMA to submit a

request to SIIG RMA. Your RMA request will be processed, if the

product is determined to be defective, an RMA number will be

issued.

Step 2: After obtaining an RMA number, ship the product.

•Properly pack the product for shipping. All software, cable(s)

and any other accessories that came with the original package

must be included.

•Clearly write your RMA number on the top of the returned

package. SIIG will refuse to accept any shipping package, and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

•You are responsible for the cost of shipping. Ship the product

to the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

RMA #:

•SIIG will ship the repaired or replaced product via Ground

in the U.S. and International Economy outside of the U.S. at

no cost to the customer.

VGA & RS-232 CAT5 Extender with RGB Delay Control is a trademark of SIIG, Inc. SIIG and the SIIG

logoareregisteredtrademarksofSIIG,Inc. Allothernamesusedinthispublicationareforidentification

only and may be trademarks of their respective owners.

PRODUCT NAME

VGA& RS-232 CAT5 Extender with RGB Delay Control

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

Phone: 510-657-8688

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity

solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,

and legacy I/O adapters) that bridge the connection between Desktop/

Notebook systems and external peripherals. SIIG continues to grow by

adding A/V and Digital Signage connectivity solutions to our extensive

portfolio. Allcentered around the distribution and switching of A/V signals

overCAT5/6,theseproductsincludematrixswitches,distributionamplifiers,

extenders, converters, splitters, cabling, and more.

SIIG is the premier one-stop source of upgrades and is committed to

providing high quality products while keeping economical and competitive

prices. High-quality control standards are evident by one of the lowest

defective return rates in the industry. Our products offer comprehensive

user manuals, user-friendly features, and most products are backed by a

lifetime warranty.

SIIG products can be found in many computer retail stores, mail order

catalogs, and e-commerce sites in the Americas, as well as through major

distributors, system integrators, and VARs.

Inhaltsverzeichnis

Andere SIIG Extender Handbücher

SIIG

SIIG AV-GM04T3-S1 Series Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02D3-S1 Bedienungsanleitung

SIIG

SIIG CE-H24B11-S1 Bedienungsanleitung

SIIG

SIIG CE-H23811-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02S3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02M3-S1 Series Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02J3-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04S3-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM04D3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03K3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04Q3-S1 Bedienungsanleitung

SIIG

SIIG HDMI 4K HDBaseT Extender Over Single Cat5e/6 Cable with IR Control -... Produktinformationsblatt

SIIG

SIIG CE-H20S11-S1 Bedienungsanleitung

SIIG

SIIG CE-HM0051-S1 Bedienungsanleitung

SIIG

SIIG CE-H22811-S1 Bedienungsanleitung

SIIG

SIIG CE-H22N15-S1 Produktinformationsblatt

SIIG

SIIG AV-GM02X3-S1 Bedienungsanleitung

SIIG

SIIG CE-H21U11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03S3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02R3-S1 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung