SIIG CE-DP0511-S1 Bedienungsanleitung

Introduction

TheDisplayPorttoCAT5eDaisyChain HD Extender Kit with

RS-232 & IR extends DisplayPort signal over one Cat5/6

cable up to 330ft and is cascade connection supported.

Features and Benefits

• Extend DisplayPort signals up to 100m over Cat5e/

6 cabling

• Cascade receivers up to 10 layers

• Supports video high resolution Full HD 1080p, 1920

x 1080@60Hz

• Supports local DisplayPort and audio output

• Metal housing with mounting mechanism

PackageContents

CE-DP0511-S1

04-0955A

DisplayPort to CAT5e Daisy

Chain HD Extender Kit

with RS-232 & IR

Installation Guide

Layout

Transmitter Unit (Tx)

Figure 1: Transmitter side panel

•DC 5V: DC 5V power jack. Plug the included power

adapter here

•PWR:LEDindicatorforpowerstatus.On/Offwhen

the Transmitter is powered on/off

CE-DP0611-S1

•LINK: LED indicator for link status. On when the

connection of Transmitter and Receiver is established

and detected

•DP IN: DisplayPort signal input port. Connect this

port to your DisplayPort source device by using a

DisplayPort cable (not included)

•DP OUT: DisplayPort signal output port. Connect

this port to a local DisplayPort display by using a

DisplayPort cable (not included)

• : Audio output port. Connect to the a local

3.5mm audio speaker by using the included audio

cable

•LINE : Signal output port, connected with Receiver's

LINE port by using a CAT X cable (not included)

•IR: Connect to the included IR blaster cable

•RS-232: RS-232 control port. Plug the included

3.5mm to RS-232 cable then an RS-232 cable here, if

needed

•RESET: Use the fine end of any object to press and

hold the bottom to return to default settings

Receiver / Repeater Unit (Rx)

Figure 2: Receiver/Repeater side panel

•DC 5V: DC 5V power jack. Plug the included power

adapter here

•IR: Connect to the included IR receiver cable

•RESET: Use the fine end of any object to press and

hold the bottom to return to default settings

•PWR:LEDindicatorforpowerstatus.On/Offwhen

the Receiver is powered on/off

•LINK: LED indicator for link status. On when the

connection of Transmitter and Receiver/Repeater is

established and detected

•RS-232: RS-232 control port. Plug the included

3.5mm to RS-232 cable then an RS-232 cable here, if

needed

•DP OUT: DisplayPort signal output port. Connect

this port to the remote DisplayPort display by using

a DisplayPort cable (not included)

• : Audio output port. Connect to the a remote

3.5mm audio speaker by using the included audio

cable

•LINE 1-3: Signal input port, connected with

Transmitter's LINE port by using a CAT X cable (not

included).

Either one port is connected to the Transmitter unit,

the other two ports could be connected to other

Receivers/Repeaters for further signal extension or

expansion. See the Function Diagram section on

page 7-10 for more details

IR Extension Cables

To control the source device from Receiver's end:

1. Plug the IR blaster cable to the Transmitter's IR

connector, then plug the IR receiver cable to the

Receiver's IR connector.

2. Point your source device's remote control to the IR

receiver's eye, the command will be sent to

Transmitter end, and the connected source device

will enforce the command accordingly.

Figure 3a: IR blaster cable Figure 3b: IR receiver cable

Hardware Installation

1. Power off all devices, including the source device

and display.

2. Connect your DisplayPort source (such as a PC or

NB) to the transmitter's DP IN connector by using a

DisplayPort cable.

3. ConnectthelocalDisplayPortdisplayto Transmitter's

DP OUT.

source

device

Figure 4

local

display

4. Connect remote DisplayPort display (such as a LCD

TV) to the receiver's DP OUT connector.

output

display

Figure 5

5. Connect the IR blaster cable and IR receiver cable

to the Transmitter and Receiver's IR ports separately.

Skip this step if not needed.

6. Connect the two 3.5mm to RS-232 cables to the

Transmitter and Receiver's RS-232 ports separately.

Skip this step if RS-232 controlling is not needed.

7. Connect your CAT5/6 cable between the

Transmitter's and Receiver's LINE port. Make sure

the CAT5/6 LAN cable is securely connected.

Figure 6

remote

output

display

local

output

display

source

device

8. Each Receiver/Repeater can cascade-chainable to 2

more Receivers/Repeaters for further extending or

expanding . Skip this step if not needed.

9. Connectthespeakersto the Transmitter andReceiver's

audio out ports separately.

Skip this step if not needed.

CAT5/

6 cable

Figure 7

source

local DP

display

remote DP

display

• The extension distance through CAT. X cable is up

to 100 meters for one layer

10. Plug the included power adapters into the DC 5V

powerjack oftheTransmitter and Receiverseparately.

Power on the connected source device and

display(s), the Extender kit is ready for use.

Function Diagram

Basic connection

IR receiver

cable

(optional)

IR blaster

cable

(optional)

1CAT. X cable

DisplayPort cable

1CAT. X cable

DisplayPort cable

AdvancedConnections

Daisy Chain Connection

Figure 8

• The extension distance through CAT. X cable is up

to 100 meters for one layer

Display

source

Display

1Rx

Cascade Connection

source

Display

Figure 9

• Cascadereceiversup to 10 layers; extension distance

through CAT. X cable up to 100 meters for one layer

1CAT. X cable

DisplayPort cable

Gigabit Ethernet Switch Connection

Figure 10: Used with Gigabit Ethernet switch

source

Display

1 1

Gigabit

switch

Display

• Connect with the Gigabit Ethernet switch especially

when your Tx or Rx unit has only one signal input/

output port

• The extension distance through CAT. X cable is up

to 100 meters for one layer

Display

1CAT. X cable

DisplayPort cable

Inhaltsverzeichnis

Andere SIIG Extender Handbücher

SIIG

SIIG CE-H20011-S1 Bedienungsanleitung

SIIG

SIIG CE-H20211-S1 Bedienungsanleitung

SIIG

SIIG CE-H20S11-S1 Bedienungsanleitung

SIIG

SIIG CE-H22T11-S1 Bedienungsanleitung

SIIG

SIIG CE-H24B11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02M3-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM0463-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04Q3-S1 Bedienungsanleitung

SIIG

SIIG CE-HM0052-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03K3-S1 Bedienungsanleitung

SIIG

SIIG CE-H23T11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04G3-S1-U Bedienungsanleitung

SIIG

SIIG AV-GM04D3-S1 Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0403-S1 Series Bedienungsanleitung

SIIG

SIIG JU-EX0011-S1 Bedienungsanleitung

SIIG

SIIG CE-H23411-S1 Produktinformationsblatt

SIIG

SIIG AV-GM02S3-S1 Bedienungsanleitung

SIIG

SIIG CE-H23E11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03W3-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04S3-S1 Series Bedienungsanleitung

SIIG

SIIG CE-H24G11-S1 Bedienungsanleitung

SIIG

SIIG CE-H21U11-S1 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung