SIIG AV-GM03W3-S1 Bedienungsanleitung

Composite & Audio over CAT.X Extender with

RGB Delay Control

P/N: AV-GM03W3-S1

Safety and Notice

The AV-GM03W3-S1 Composite & Audio over CAT.X Extender with RGB Delay Control has been

tested for conformance to safety regulations and requirements, and has been certified for

international use. However, like all electronic equipments, the AV-GM03W3-S1 should be used

with care. Please read and follow the safety instructions to protect yourself from possible

injury and to minimize the risk of damage to the unit.

●Follow all instructions and warnings marked on this unit.

●Do not attempt to service this unit yourself, except where explained in this manual.

●Provide proper ventilation and air circulation and do not use near water.

●Keep objects that might damage the device and assure that the placement of this unit is on a

stable surface.

●Use only the power adapter and power cords and connection cables designed for this unit.

●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the

device before cleaning.

TABLE OF CONTENTS

INTRODUCTION................................................................................................................ 1

FEATURES........................................................................................................................ 1

PACKAGE CONTENTS ................................................................................................... 1

SPECIFICATIONS.............................................................................................................. 2

PANEL DESCRIPTION ...................................................................................................... 3

Transmitting unit ►TX............................................................................................ 3

Receiving unit ► RX ............................................................................................... 4

CONNECTION DIAGRAM.................................................................................................. 5

HARDWARE INSTALLATION ............................................................................................ 6

NOTICE.............................................................................................................................. 7

LIMITED WARRANTY........................................................................................................ 8

INTRODUCTION

With only one cost effective CAT.X cable, the AV-GM03W3-S1 lets you extend Composite signals up

to 330m (1,000ft). The devices are composed of a transmitter and a receiver. The transmitter is

installed near the signal source, and the receiver AV-GM03W3-S1-RX is placed near the desired

display. With built-in EQ and GAIN control, the transmission path can be adjusted to adapt the cable

quality and video bandwidth. Furthermore, the Composite RGB delay control [de-skew] function

provides the compensation among R, G, B signals due to long transmission or through normal LAN

cable. Analog stereo audio signals can be sent along with high quality Composite signal over long

distance LAN cable.

FEATURES

●Supports up to 720P@60Hz, 1080i@60Hz, 1080P@30Hz to 330m (1,000ft)

●Supports analog stereo audio and S/PDIF digital audio

●Adjustable equalization and gain control on RX unit

●De-skew compensation available for RGB delay control

●Wall mounting case for secure installation

PACKAGE CONTENTS

●1x AV-GM03W3-S1 [TX&RX]

●2x 5V power supply unit

●1x User Manual

●1~3x VGA-component breakout cable [optional accessory]

SPECIFICATIONS

Model Name

AV-GM03W3-S1

Technical

AV-GM03W3-S1

Role of usage

Transmitter [TX]

Receiver [RX]

Video bandwidth

350MHz

Video support

720P@60Hz, 1080i@60Hz, 1080P@30Hz

Video Transmission

330m (1,000ft) [CAT5e]

Audio support

Stereo/ S/PDIF

Input video signal

1.2 Volts [peak-to-peak]

Equalization

Continuous analog control

RGB delay control

Yes

ESD protection

[1] Human body model —±19kV [air-gap discharge] & ±12kV [contact

discharge]

[2] Core chipset —±8kV

Input

4x RCA

1x 3.5mm

1xRJ-45

Output

1x RJ-45

1x 3.5mm

1x RCA

4x RCA

1x 3.5mm

RJ-45 connector

WE/SS 8P8C with 2 LED indicators

RCA connector

YPbPr/ S/PDIF digital audio

3.5mm connector

Earphone jack for analog stereo audio

Mechanical

AV-GM03W3-S1

Housing

Metal enclosure

Dimensions

[L x W x H]

Model

[TX/RX] –123 x 95 x 25mm [4.8”x3.7”x1”]

Package

330 x 200 x 95mm [1’1”x7.9”x3.7”]

Carton

495 x 440 x 380mm [1’7.5”x1’5.3”x1’3”]

Weight

Model

[TX]–390g [14oz] / [RX]–380g [13oz]

Package

1250g [2.8 lbs]

Fixedness

Wall-mounting case with screws

Power supply

Inter-locked 5V 2A DC

Power consumption

6 Watts [max]

Operation

temperature

0~40C [32~104F]

Storage temperature

-20~60C [-4~140F]

Relative humidity

20~90% RH [no condensation]

PANEL DESCRIPTION

Transmitting unit ►AV-GM03W3-S1-TX

Front Panel

1. Stereo audio input –L

2. Stereo audio input –R

3. S/PDIF audio input

4. Push-in button: select between S/PDIF and analog stereo audio [button down-S/PDIF,

button up-Stereo]

5. Composite –Y input

6. Composite –Pb input

7. Composite –Pr input

Rear Panel

8. +5V DC: inter-locked power jack to connect to 5V DC power supply unit

9. RJ-45 OUT: plug in a Cat-5/5e/6 cable that needs to be linked to the RJ-45 connector of the

receiving unit AV-GM03W3-S1[Rx]

Receiving unit ►AV-GM03W3-S1-RX

Front Panel

10. Stereo audio output –L

11. Stereo audio output –R

12. S/PDIF audio output

13. Composite –Y output

14. Composite –Pb output

15. Composite –Pr output

Rear Panel

16. +5V DC power jack: connect to 5V DC power supply

17. RJ-45 IN: Plug in a CAT-5/5e/6 cable that needs to be linked to the RJ-45 connector of the

transmitting unit AV-GM03W3-S1-TX.

18. EQ: Rotary control for equalization of R, G, B, respectively

19. GAIN: Rotary control for gain control of Y respectively

20. GAIN: Rotary control for gain control of Pb respectively

21. GAIN: Rotary control for gain control of Pr respectively

22. Rotary control: R=0~2, G=3~5, B=6~7, for de-skew compensation on respective color channel

(for RGB delay control)

23. –:Push button for decrease a level of de-skew compensation (for RGB delay control)

24. +: Push button for decrease a level of de-skew compensation (for RGB delay control)

CONNECTION DIAGRAM

HARDWARE INSTALLATION

1. Connect your YPbPr and audio source to the transmitting unit.

2. Connect your display and speakers to the receiving unit.

3. Connect your CAT-5/5e/6 cable between the transmitting and receiving units.

4. Make sure your CAT-5/5e/6 cable is tightly connected and not loose.

5. Plug in 5V DC power cord to the power jack of the receiving unit.

6. Plug in 5V DC power cord to the power jack of the transmitting unit.

7. If a blurred video is seen or even worse, not displayed at all, try to adjust the EQ and Gain

rotary controls to improve the cable skew. GAIN rotary controls are designed for gain control,

and EQ rotary controls are designed for equalizing the wave form of the receiving video signal.

It is suggested to begin with adjusting the rotary control of EQ to get the input video displayed

first, and then the GAIN according to the video you see on the screen.

Please follow the steps as below to adjust EQ and Gain.

a. Set the rotary control of Y、Pb(Cb)、Pr(Cr) to max

b. Set the rotary control of equalization to the middle position, and then adjust the EQ to left

or right direction until the image is clear

c. After the image is clear, please adjust the rotary control of Y、Pb(Cb)、Pr(Cr)

P.S. Please check the RJ-45 connector and Cat.X cable and make sure they are not loose if the

image can not be adjusted correctly

8. RGB delay control [De-skew] offers the flexible functionality to allow skew compensation

among VGA R, G, B signals due to long transmission or thru low quality cable. By adjusting the

rotary switch to choose R, G or B color channel at first, then use the push buttons to increase

or decrease the delay in the corresponding color channel. There are totally 31 steps, each step

with 2ns difference, for adjusting the delay between each color individually. Then the graphics

quality can be further assured.

NOTICE

1. All transmission distances are measured using Belden 1583A CAT-5e 125MHz LAN cable and

ASTRODESIGN Video Signal Generator VG-859C. The transmission distance is defined as the

distance between the video source and the VGA display.

2. The transmission length is largely affected by the type of LAN cables, the type of video sources,

and the type of display. The testing result shows solid LAN cables (usually in bulk cable 300m or

1000ft form) can transmit a lot longer signals than stranded LAN cables (usually in patch cord

form). Shielded STP cables are better suit than unshielded UTP cables. A solid UTP CAT5e cable

shows longer transmission length than stranded STP CAT6 cable. For long extension users, solid

cables are your only choice.

3. To reduce the interference among the unshielded twisted pairs of wires in LAN cable, you can

use shielded LAN cables to improve EMI problems, which is worsen in long transmission.

4. Because the quality of the LAN cables has the major effects in how long transmission distance

will be made and how good is the received display, the actual transmission length is subject to

your LAN cables. For resolution greater than 1080i or 1280x1024, a CAT-6 cable is

recommended.

5. The analog audio is sampled by 48kHz before transmission; on the remote RX unit with S/PDIF

audio input, the only supported sampling frequency is 48kHz.

Performance Guide for HDMI over Category Cable Transmission

Performance rating

Type of category cable

Wiring

Shielding

CAT5

CAT5e

CAT6

Solid

Unshielded (UTP)







Shielded (STP)





Stranded

Unshielded (UTP)





Shielded (STP)





Termination

Please use EIA/TIA-568-B termination (T568B) at any

time

LIMITED WARRANTY

The SELLER warrants the AV-GM03W3-S1 Composite & Audio over CAT.X Extender with

RGB Delay Control to be free from defects in the material and workmanship for 3 years from the

date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good

working order within 3 years warranty period, The SELLER, at its option, repair or replace the unit,

provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized

modifications including static discharge and power surge. This warranty is offered by the SELLER for

its BUYER with direct transaction only. This warranty is void if the warranty seal on the metal

housing is broken.

Unit that fails under conditions other than those covered will be repaired at the current price of

parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day

of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or

assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted

without a return authorization number.

The warranty is in lieu of all other warranties expressed or implied, including without

limitations, any other implied warranty or fitness or merchantability for any particular purpose, all

of which are expressly disclaimed.

Proof of sale may be required in order to claim warranty. Customers outside Taiwan are

responsible for shipping charges to and from the SELLER. Cables are limited to a 30 day warranty

and cable must be free from any markings, scratches, and neatly coiled.

The content of this manual has been carefully checked and is believed to be accurate. However,

The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual.

The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages

resulting from any defect or omission in this manual, even if advised of the possibility of such

damages. Also, the technical information contained herein regarding the AV-GM03W3-S1 features

and specifications is subject to change without further notice.

April, 2018

Support

For more info or tech support

http://www.siig.com/support

Inhaltsverzeichnis

Andere SIIG Extender Handbücher

SIIG

SIIG AV-GM03G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02R3-S1 Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG CE-H24G11-S1 Bedienungsanleitung

SIIG

SIIG HDMI 4K HDBaseT Extender Over Single Cat5e/6 Cable with IR Control -... Produktinformationsblatt

SIIG

SIIG AV-GM03S3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04Q3-S1 Bedienungsanleitung

SIIG

SIIG CE-H23E11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0403-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM04G3-S1-U Bedienungsanleitung

SIIG

SIIG CE-D20012-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG CE-H23811-S1 Bedienungsanleitung

SIIG

SIIG CE-H20011-S1 Bedienungsanleitung

SIIG

SIIG CE-H20S11-S1 Bedienungsanleitung

SIIG

SIIG CE-H23411-S1 Produktinformationsblatt

SIIG

SIIG CE-KV0511-S1 Bedienungsanleitung

SIIG

SIIG CE-H22T11-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG CE-VG0711-SA Bedienungsanleitung

SIIG

SIIG AV-GM02D3-S1 Bedienungsanleitung

SIIG

SIIG CE-HM0052-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0413-S1 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung