SIIG CE-H20S11-S1 Bedienungsanleitung

Full HD 1080P HDMI

Wireless Extender

Quick Installation Guide

04-0711B

Introduction

The Full HD 1080P HDMI Wireless Extender

transmits HDMI signals wirelessly up to 50ft.

Key Features and Benefits

• Compliant with WDHI 1.0, HDCP 2.0, and

HDMI standards

• 5GHz unlicensed band with support for

Dynamic Frequency Selection (DFS)

• Supports video bandwidth up the 3Gb/s

• Supports 1080p/60GHz non-compressing

video

System Requirements

• PC or A/V devices with an available HDMI

output port

• HDMI display

Package Contents

• HDMI Transmitter (Tx)

• HDMI Receiver (Rx)

• DC 12V Power Supply (2)

• IR cable

• HDMI cable (2)

• Quick installation guide

Layout

Figure 1: Transmitter (Tx)

On/ Off Switch

Power LED Indicator

Wireless LED

Indicator

Remote Extender

Reset Button

HDMI Input

Antenna

Power Jack

Figure 2: Receiver (Rx)

On / Off Switch

HDMI Output

Antenna

Power LED Indicator

Wireless LED

Indicator

Reset Button

Power Jack

Figure 3: IR cable

LED Indicators

Power LED

• Red: Power Off

• Blue: Power On

Wireless LED

• Red: Wireless Dis-connected

• Blue: Wireless Connected

• Red and Blue Blinking: Search Signal

Hardware Installation

1. Power off all devices, including the source

HDMI device and HDMI display.

2. Connect an HDMI cable (included) from

the HDMI device to the Transmitter's HDMI

Input.

3. Connect the IR emitter cable to the HDMI

Transmitter (Tx) and point the emitter

directly to the HDMI device's IR.

Note: Please make sure that you place the

IR emitter close to the HDMI device's IR for

a good signal.

4. Connect an HDMI cable (included) from

the Receiver's HDMI Output to the TV's

HDMI Input.

5. Plug the DC 12V Power Supply into the

Transmitter's power jack, then plug it into

a reliable power source.

6. Plug the DC 12V Power Supply into the

Receiver's power jack, then plug it into a

reliable power source.

7. Push the On/Off switch to power on both

the Transmitter (Tx) and Receiver (Rx).

8. The Full HD 1080P HDMI Wireless Extender

is ready for use.

FAQ

Question 1: The power indicator (red LED)

doesn’t light up.

Answer: Verify that the proper cables have been

selected and installed between the Transmitter's

input and your HD device's output.

Question 2: No video is displayed on your TV

screen.

Answer: Make sure you select HDMI as the input

source in your TV.

• Wireless LED Lighting up in Red

- Make sure the proper cables are connected

between the Transmitter (Tx) and your AV

devices.

- Make sure your source devices connected

to the Transmitter (Tx) are powered on.

- Make sure the proper cables are connected

between the Receiver (Rx) and your HDTV.

• Make sure the transmission range between

Transmitter (Tx) and Receiver (Rx) is not

over 66 feet (LOS-line of sight) transmission

distance. Move the Transmitter (Tx) closer

to the Receiver (Rx).

• Verify the Power LED Indicator and

Wireless LED Indicator of both Transmitter

(Tx) and Receiver (Rx). Wireless LED

Lighting up in Red OSD shows: Searching

available channels…..

• Check if the power adapters of Transmitter

(Tx) and Receiver (Rx) are inserted into a

functioning power outlet properly.

Question 3: Poor picture quality or intermittent

video.

Answer: Make sure the transmission distance is

less than 66 feet (LOS).

• Check if the video resolution of your HDMI

source device matches the Transmitter (Tx)

and Receiver (Rx) Specification.

Question 4: No audio.

Answer: Check your TV’s volume is properly set

and not set in “MUTE” mode.

• Check if the audio connectors are properly

connected.

• Make sure the audio bit rate from the source

device can be supported by Transmitter

(Tx) and Receiver (Rx).

Question 5: IR Blaster can’t control source device.

Answer: Check the position of IR sensor of source

device. Make sure the IR emitter's sensor is close

and points to the source devices IR sensor.

Blank Page

Inhaltsverzeichnis

Andere SIIG Extender Handbücher

SIIG

SIIG AV-GM03S3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04Q3-S1 Bedienungsanleitung

SIIG

SIIG HDMI 4K HDBaseT Extender Over Single Cat5e/6 Cable with IR Control -... Produktinformationsblatt

SIIG

SIIG CE-H22N15-S1 Produktinformationsblatt

SIIG

SIIG AV-GM02M3-S1 Series Bedienungsanleitung

SIIG

SIIG CE-H24G11-S1 Bedienungsanleitung

SIIG

SIIG CE-D20111-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03T3-S1 Bedienungsanleitung

SIIG

SIIG CE-VG0711-SA Bedienungsanleitung

SIIG

SIIG AV-GM0473-S1 Bedienungsanleitung

SIIG

SIIG CE-H27611-S1 Bedienungsanleitung

SIIG

SIIG CE-H26411-S1 Bedienungsanleitung

SIIG

SIIG CE-D20012-S1 Bedienungsanleitung

SIIG

SIIG CE-H22811-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04A3-S1-IR Bedienungsanleitung

SIIG

SIIG CE-HM0051-S1 Bedienungsanleitung

SIIG

SIIG AV-GM04S3-S1 Series Bedienungsanleitung

SIIG

SIIG AV-GM04D3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM03G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM02X3-S1 Bedienungsanleitung

SIIG

SIIG CE-H22T11-S1 Bedienungsanleitung

SIIG

SIIG CE-DV0061-S1 Bedienungsanleitung

SIIG

SIIG CE-H23411-S1 Produktinformationsblatt

SIIG

SIIG AV-GM03X3-S1 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung