SIIG AV-GM07X3-S1 Bedienungsanleitung

8x8 HDMI Matrix Switcher with Full 3D Support

P/N: AV-GM07X3-S1

Safety and Notice

The AV-GM07X3-S1 8x8 HDMI Matrix Switcher with Full 3D Support has been tested for

conformance to safety regulations and requirements, and has been certified for international

use. However, like all electronic equipments, the AV-GM07X3-S1 should be used with care.

Please read and follow the safety instructions to protect yourself from possible injury and to

minimize the risk of damage to the unit.

●Follow all instructions and warnings marked on this unit.

●Do not attempt to service this unit yourself, except where explained in this manual.

●Provide proper ventilation and air circulation and do not use near water.

●Keep objects that might damage the device and assure that the placement of this unit is on a

stable surface.

●Use only the power adapter and power cords and connection cables designed for this unit.

●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the

device before cleaning.

TABLE OF CONTENTS

INTRODUCTION.................................................................................................................1

FEATURES.........................................................................................................................1

PACKAGE CONTENTS......................................................................................................1

SPECIFICATIONS..............................................................................................................2

PANEL DESCRIPTIONS.....................................................................................................3

IR PASS-THROUGH...........................................................................................................5

HARDWARE INSTALLATION.............................................................................................6

CONNECTION DIAGRAM ..................................................................................................6

OPERATION APPROACH..................................................................................................7

EDID LEARNING..............................................................................................................19

WARRANTY .....................................................................................................................20

INTRODUCTION

The AV-GM07X3-S1 8x8 HDMI Matrix Switcher with Full 3D Support provides the most flexible

and cost effective solution in the market to route high definition video sources plus multi-channel

(up to 7.1-channel) digital audio from any of the four HDMI sources to the remote displays at the

same time. This solution is well suited for use in home theater, conference room presentation

systems, or other similar setting or application

FEATURES

●Support HDMI Deep Color & full 3D

●HDCP compliant

●Allows any source to be displayed on multiple displays at the same time

●Allows any HDMI display to view any HDMI source at any time

●Supports 7.1 channel digital audio

●Supports default HDMI EDID and learns the EDID of displays

●The matrix master can switch every output channels to any HDMI inputs by push-in button, IR

remote control, RS-232 control, and Ethernet control

●Easy installation with rack-mounting and wall-mounting designs for master and receiver

respectively

●Fast response time –2~5 seconds for channel switch

PACKAGE CONTENTS

●1x AV-GM07X3-S1

●1x IR Receiver

●1x DC 12V 5A

●1x IR Remote control*

●1x Rack-mounting ear set

●1x Installation software CD

●1x User Manual

SPECIFICATIONS

Model Name

AV-GM07X3-S1

Technical

Role of usage

True 8x8 matrix

HDMI compliance

HDMI Deep Color & full 3D

HDCP compliance

Yes

Video bandwidth

Single-link 225MHz [6.75Gbps]

Video support

480i / 480p / 720p / 1080i / 1080p60 36-bit color

Audio support

Surround sound (up to 7.1ch) or stereo digital audio

ESD protection

[1] Human body model —±19kV [air-gap discharge] & ±12kV [contact

discharge]

[2] Core chipset —±8kV

PCB stack-up

4-layer board [impedance control —differential 100Ω; single 50Ω]

Input

8x HDMI / 1x RS-232 / 1x Ethernet / 1x IR socket for IR receiver

Output

8x HDMI

HDMI Input

selection

Push-in button / IR remote control / RS-232 control / Ethernet control

IR remote control

Electro-optical characteristics: = 25° / Carrier frequency: 38kHz

HDMI connector

Type A [19-pin female]

RJ-45 connector

WE/SS 8P8C with 2 LED indicators

RS-232 connector

DE-9 [9-pin D-sub female]

3.5mm connector

[System IR] Receives IR commands from remote control

Mechanical

AV-GM07X3-S1

Enclosure

Metal case

Dimensions

(L x W x H)

Model

440 x 149 x 41 mm [17" x 5.9" x 1.6"]

Package

524 x 265 x 76 mm [1'7" x 10.4" x 3"]

Carton

542 x 411 x 300 mm [1'8" x 1'3" x 11.8"]

Weight

Model

2033g [71.7oz]

* Additional IR remote controllers can be purchased as optional accessories to control the

HDMI sources located separately.

Package

3062g [6.8 lbs]

Fixedness

1RU rack-mount with ears Wall hanging holes

Power supply

12V 5A DC

Power consumption

[max]

Operation temperature

0~40°C [32~104°F]

Storage temperature

-20~60°C [-4~140°F]

Relative humidity

20~90% RH [no condensation]

PANEL DESCRIPTIONS

Front Panel

1. Source Status: Input source indicator LED

2. IR SENSOR: IR sensor for receiving the IR commands from IR remote

3. Output Push Button & 7-segment LED: Front panel push buttons used to select the number of

display channel & LED display for output ports

4. Input Push Button & 7-segment LED: Front panel push buttons used to select the number of

input source & LED display for input channel

Rear Panel

5. +12V DC: 12V DC power jack

6. Ethernet: Ethernet control port

7. RS-232: RS-232 control port

8. System IR Receiver: Ext. IR receiver

9. INPUT 1-8: HDMI inputs

10. OUTPUT 1-8: HDMI outputs

IR PASS-THROUGH

IR Receiver

Sockets

AV-GM07X3-S1

System IR: Receives IR commands from remote control

Definition of IR Earphone Jack

IR Receiver

Incorrect placement of IR Blaster and Receiver may result in the failure of the IR

extenders. Please check carefully before plugging in the IR extender to the

respective IR sockets. Warranty will not cover the damage.

1. IR Signal [34-40 kHz]

2. Grounding

3. Power

HARDWARE INSTALLATION

AV-GM07X3-S1 as master

1. Connect all sources to HDMI Inputs on the 8x8 HDMI matrix master AV-GM07X3-S1.

2. Connect each output port on the AV-GM07X3-S1 to respective input

3. Connect IR blaster to the AV-GM07X3-S1 and direct the IR blaster to point towards the built-in IR

receiver of the HDMI source devices.

4. Connect the +12V 5A DC power supply to the AV-GM07X3-S1.

5. Power on all HDMI sources.

CONNECTION DIAGRAM

You can buy any IR extension cables in the market that are compatible to the definition of

the IR sockets for the matrix if necessary for replacement use. However, IR cables longer

than 2m (6-ft) may not work.

OPERATION APPROACH

Method A: Push-in Button

1. IN/OUT MAP

1) Use the “+”or “-“ output push button to select the number of display

2) Use the “+”or “-“ input push button to select the number of input source

“+”: change selected input/output port in ascending order

“-”: change selected input/output port in descending order

After you select the desired input/output port, the LED will blink twice and the setting will be

effective

2. Save Mapping Mode

1) Keep pushing “output+ (save)”button until the output LED shows “d.” to enter the Save

Mapping Mode.

2) Use the “+”or “-“ input push button to select the mapping configuration (0~7) which you want to

save current input/output mapping

3) After you select the desired mapping configuration number, the LED will blink twice and the

mapping setting will be saved

4) If you push the “output- (preset)”button before the mapping setting is saved, the LED will show

“一”“一”to quit the Save Mapping Mode

3. Preset Mapping Mode

1) Keep pushing “output- (preset)”button until the output LED shows “P.” to enter the Preset

Mapping Mode.

2) Use the “+”or “-“ input push button to select the saved mapping configuration (0~7) which you

want to recall

3) After you select the desired mapping configuration number, the LED will blink twice and the

mapping setting will be effective

4) If you push the “output+ (save)”button before the mapping setting is effective, the LED will

show “一”“一”to quit the Preset Mapping Mode

4. Default EDID Mode

1) Push “input+(default)”button to select the input channel which you want to learn default EDID

and then keep pushing “input+(default)”button when you select your desired input channel

default

learn

preset

save

2) Push the “+”or “-” output push button and then the LED will show “E”“d” one time to enter Learn

Default EDID Mode

3) Use “+”or “-” output push button to select the default EDID mode(1~8)

4) Release “input+(default)”button after selecting the desired default EDID mode, and then the

LED will blink twice and the setting will be effective

5) It will quit the Learn Default EDID Mode if you push the “input- (learn)”button before the setting

is effective

6) The LED will show “0”“0” if the setting is success

The LED will show “F”“F” if the setting is failure

5. EDID Learning Mode

1) Push “input-(learn)”button to select the input channel which you want to learn EDID from HDMI

output and then keep pushing “input-(learn)”button when you select your desired input

channel

2) Push the “+”or “-” output push button and then the LED will show “E”“L” one time to enter Learn

Output EDID Mode

3) Use “+”or “-” output push button to select the output port number

4) Release “input-(learn)”button after selecting the desired output port number, and then the LED

will blink twice and the setting will be effective

5) It will quit the Learn Output EDID Mode if you push the “input+ (default)”button before the

setting is effective

6) The LED will show “0”“0” if the setting is success

The LED will show “F”“F” if the setting is failure

Method B: IR Remote Control

Button

Function

Power on the matrix switcher

OFF

Standby mode

MUTE

Turn off output’s video and audio

PRESET

Preset mapping mode

SAVE

Save current mapping mode

Number

buttons 1-9

Select a number

+10

Reserved

Transfer key

TAKE

Trigger the previous setting

SWITCH

Begin input and output selection

DEFAULT

EDID

Begin default EDID selection

LEARN

Begin EDID learning from one output

Inhaltsverzeichnis

Andere SIIG Matrix-Umschalter Handbücher

SIIG

SIIG CE-H27Q11-S1 Bedienungsanleitung

SIIG

SIIG CE-H24W11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0733-S1 Bedienungsanleitung

SIIG

SIIG AV-GM08G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0843-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07U3-S1-V2 Bedienungsanleitung

SIIG

SIIG AV-GM0823-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07R3-S12 Bedienungsanleitung

SIIG

SIIG AV-GM07J3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07L3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM08F3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0743-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07G3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM06Y3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07P3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07M3-S1 Bedienungsanleitung

SIIG

SIIG 4x2 HDMI Bedienungsanleitung

SIIG

SIIG AV-GM07C3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0783-S1 Bedienungsanleitung

SIIG

SIIG CE-H21F11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07N3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM06X3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07A3-S1 Bedienungsanleitung

SIIG

SIIG MA-1088D Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Kramer

Kramer VS-66H Bedienungsanleitung