SIIG 1394 Bedienungsanleitung

1394 PCI Adapter

Installation Guide

04-0224G

Introduction

The 1394 PCI Adapter is designed to add FireWire

(1394a) interface to your PC computer for easy connection

to DV camcorders, hard disk drives (self-powered),

scanners, printers and other 1394 devices.

Features and Benefits

• Compliant with IEEE 1394-1995, 1394a-2000 and

1394 OHCI 1.1 standards

• PCI 2.2 compliant and works in 32-/64-bit, 3.3V or

5V PCI slots

• Provides three high-speed FireWire ports for

connecting up to 63 devices

• Supportsbothasynchronousandisochronousdata

transfer modes

• Supports serial bus data transfer rates of 100, 200,

and 400 Mbps

System Requirements

• Pentium®

II or equivalent PC with an available PCI

slot

• Windows®

8 (32-/64-bit) / 7 (32-/64-bit) / Vista

(32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008

(32-/64-bit) / Server 2008 R2 / 2000 / ME / 98SE

Package Contents

•1394 PCI Adapter

• Installation guide

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

StaticElectricityDischarge may permanently damage your

system. Discharge any static electricity build up in your

body by touching your computer case for a few seconds.

Avoid any contact with internal parts and handle cards

only by their external edges.

1. Turn OFF the power to your computer.

2. Unplugthepowercordandremove your computer's

cover.

3. Remove the slot bracket from an available PCI slot.

4. Carefully align the card to the selected PCI slot push

the board down firmly, but gently, until it is well

seated.

5. Replace the slot bracket holding screw to secure the

card.

6. Replacethe computercoverand reconnect thepower

cord.

Driver Installation

Please make sure the board is installed before proceeding

with driver installation.

Windows 8 / 7 / Vista / XP / Server 2003 & 2008 /

Server 2008 R2 / 2000

Windows 8, 7, Vista, XP, Server 2003 & 2008, 2008 R2 and

2000 will automatically detect and install the correct driver

for the 1394 PCI adapter. No additional driver installation

is needed.

Windows ME

1. At the Add New Hardware Wizard, choose

Automatic search for a better driver

(Recommended), then click Next.

2. Click Finish and restart Windows to complete

driver installation.

Windows 98SE

1. When Windows boots up, a New Hardware Found

dialogboxshouldappearandtheOHCICompliant

IEEE 1394 Host Controller is identified.

2. At the Add New Hardware Wizard, click Next.

3. Choose Search for the best driver for your device,

and click Next.

4. Clear all check boxes, click Next and Next again.

Note: If prompted for the Windows 98SE CD, insert

it, then click OK.

5. Click Finish to complete driver installation.

To Verify Windows Installation

1. Check Device Manager to verify successful driver

installation.

For Windows 8 / 7 / XP / Server 2003 / 2000

Right click Computer or My Computer, click

Manage, click Device Manager.

For Windows Vista

Right click Computer, click Manage.Click

Continue, then click Device Manager.

For Windows Server 2008 / Server 2008 R2

Right click Computer, click Manage, double click

Diagnostics. Click Device Manager.

For Windows ME / 98SE

From the main desktop, right click My Computer,

then click Properties. Click Device Manager tab.

2. Double click 1394 Bus Controller or IEEE 1394

(Bus) host controllers option, an IEEE 1394 Host

Controller or VIA 1394 OHCI Compliance Host

Controller should be displayed.

Connecting 1394 Devices

Windows has built-in driver support for many

1394 devices. Please refer to device

manufacturer for details on how to install

device driver for your 1394 product. Different

devices may require different types of 1394

cable.

Blank Page

Technical Support and Warranty

QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at

www.siig.com and click Support. Our online support database is updated daily with

new drivers and solutions. Answers to your questions could be just a few clicks away.

You can also submit questions online and a technical support analyst will promptly

respond.

SIIG offers a lifetime manufacturer warranty with this product. This warranty covers

the original purchaser and guarantees the product to be free of any defects in materials

or workmanship for the life of the product.

SIIG will, at our discretion, repair or replace (with an identical product or product

having similar features and functionality) the product if defective in materials or

workmanship. This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state. Please see our web site for more warranty details.

If you encounter any problems with this product, please follow the procedures below.

A) If it is within the store's return policy period, please return the product to the store

where you purchased from.

B) If your purchase has passed the store's return policy period, please follow the steps

below to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, clickSupport, then REQUEST A PRODUCT REPLACEMENT

to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request

will be processed, if the product is determined to be defective, an RMA number will

be issued.

Step 2: After obtaining an RMA number, ship the product.

• Properly pack the product for shipping. All accessories that came with the

original package must be included.

• Clearly write your RMA number on the top of the returned package. SIIG will

refuse to accept any shipping package, and will not be responsible for a product

returned without an RMA number posted on the outside of the shipping

carton.

• You are responsible for the cost of shipping to SIIG. Ship the product to the

following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

RMA #:

• SIIG will ship the repaired or replaced product via Ground in the U.S. and

International Economy outside of the U.S. at no cost to the customer.

PRODUCTNAME

1394 PCI Adapter

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG,Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

Phone: 510-657-8688

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity

solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,

and legacy I/O adapters) that bridge the connection between Desktop/

Notebooksystems andexternal peripherals. SIIGcontinues togrow byadding

A/V and Digital Signage connectivity solutions to our extensive portfolio.

SIIGproducts offercomprehensiveuser manuals,manyuser-friendly features,

and are backed by an extensive manufacturer warranty. High quality control

standards are evident by the overall ease of installation and compatibility of

our products, as well as one of the lowest defective return rates in the industry.

SIIG products can be found in computer retail stores, mail order catalogs,

throughmajor distributors,system integrators,and VARsin theAmericas and

the UK, and through e-commerce sites.

1394 PCI Adapter is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered

trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft

Corporation. All other names used in this publication are for identification only and may be

trademarks of their respective owners.

Inhaltsverzeichnis

Andere SIIG PCI-Karte Handbücher

SIIG

SIIG CyberPro PCI 1S Bedienungsanleitung

SIIG

SIIG SIIG 2S1P Combo-Value Bedienungsanleitung

SIIG

SIIG SC-SA4M12 Bedienungsanleitung

SIIG

SIIG CyberPro PCI 2S Bedienungsanleitung

SIIG

SIIG JJ-P02D11-S6 Bedienungsanleitung

SIIG

SIIG LB-US0614-S1 Bedienungsanleitung

SIIG

SIIG DP CyberSerial PCI Bedienungsanleitung

SIIG

SIIG JU-EC2012-S1 Bedienungsanleitung

SIIG

SIIG JJ-P02012 Bedienungsanleitung

SIIG

SIIG Cyber 2S1P PCI Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 5-Port PCI Bedienungsanleitung

SIIG

SIIG Cyber 1S1P PCI Bedienungsanleitung

SIIG

SIIG 1394 PCI Adapter Bedienungsanleitung

SIIG

SIIG SC-SA3012-S1 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCIe Bedienungsanleitung

SIIG

SIIG Cyber 1S1P PCI Bedienungsanleitung

SIIG

SIIG SATA II-150 PCI Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 4-Port PCI Bedienungsanleitung

SIIG

SIIG SC-SAE412-S3 Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

SIIG

SIIG DP CyberSerial 4S PCIe Bedienungsanleitung

SIIG

SIIG 04-0358C Bedienungsanleitung

SIIG

SIIG Cyber 2S1P 950 PCI Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung

Alpha Networks

Alpha Networks WMP-A13V Bedienungsanleitung