SIIG Cyber 1S1P PCI Bedienungsanleitung

04-0344C

Introducing the Cyber 1S1P PCI

The Cyber 1S1P PCI high-speed serial I/O card provides

one 9-pin serial port and one parallel port.

FeaturesandBenefits

•Conforms to PCI v2.2 Plug and Play

•Full support for Windows-based software

•Reduces CPU load and improves system

performance dramatically

•IRQ sharing feature reduces IRQ conflicts

•High-speed serial port (9-pin) works with 56K V.90

external modems, ISDN terminal adapters, PDAs,

digital cameras, label printers and other serial port

devices

•Built-in FIFO buffers dramatically increase data

transmit/receivespeed,especiallyunderWindows'

multitasking environment

•Each serial port can be configured for either 5v or

12v output, for serial devices that require power

•IEEE 1284 compliant SPP/EPP/ECP parallel port

SystemRequirements

•Pentium or equivalent computer with an available

PCI slot

•Windows®95/98/98SE/ME/NT 4.0/2000/XP (32-

/64-bit)/Server2003(32-/64-bit)/Vista(32-/64-bit)

Cyber 1S1P PCI

Quick Installation Guide

PackageContents

•Cyber 1S1P PCI board

• Driver CD

• Quick Installation Guide

Layout

Figure 1. Layout

JumperSettings(JP1)

Open = 0 volts (default)

Short 1-2 = 5V

Short 2-3 = 12V

Note: Most serial devices do not require additional

power through the serial port. Refer to your serial

device's manual for more information. This jumper

can be removed if it's not used.

JP1

Serial Port

Parallel Port

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer’s case for a few

seconds. Avoid any contact with internal parts and

handle cards only by their external edges.

1. Turn OFF the power to your computer and any

other connected peripheral devices.

2. Unplug the power cord from the back of the

computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. Set JP1 jumper settings to the desired voltage only

if your serial device needs additional power from

the serial port. However, most serial devices do not

require additional power. For more information,

see Figure 1 on page 2. Skip this step if power is not

required.

6. To install the card, carefully align the card's bus

connector with the selected PCI slot on the

motherboard. Push the board down firmly, but

gently, until it is well seated.

7. Replace the slot bracket holding screw to secure the

card.

8. Replacethecomputercoverandreconnect thepower

cord.

Driver Installation

This section provides information on how to install the

Cyber 1S1P PCI drivers.

Windows95

1. At the Update Device Driver Wizard window, click

Next.

2. Insert the driver CD, and click Other Locations.

Type in D:\9x, click OK, then Finish. (Change D: to

match your CD-ROM drive letter)

3. From the Insert Disk window, click OK. When the

Copying Files dialog box appears, type in

D:\9x, then click OK.

4. Repeat steps 1-3.

5. Restart Windows to complete the installation.

Windows98/98SE

1. At the Add New Hardware Wizard window, click

Next.

2. Select Search for the best driver for your device

(Recommended), then click Next.

3. Select Specify a location, uncheck the other boxes,

insert the driver CD, type in D:\9x, then click Next.

(Change D: to match your CD-ROM drive letter)

4. Click Next, then Finish.

5. Repeat steps 1-4.

6. Restart Windows to complete the installation.

WindowsME

1. At the Add New Hardware Wizard, choose Specify

the location of the driver (Advanced), then click

Next.

2. Check Specify a location, uncheck the other box,

insert the driver CD, type in D:\Me, then click Next.

(Change D: to match your CD-ROM drive letter)

3. Click Next and Finish.

4. Repeat steps 1-3.

5. Restart Windows to complete the installation.

ToVerifyWindows95/98/98SE/MEInstallation

1. From the main desktop, right click My Computer,

click Properties, then click Device Manager.

2. Double click Ports (COM & LPT), CyberSerial PCI

16Cxxx..., Printer Port..., and CyberParallel PCI

should be displayed.

3. Double click Multi-function adapters, SIIG

CyberPro 1S1P PCI board should be displayed.

WindowsNT4.0

1. From the desktop click Start, then Run.

2. Insert the driver CD, type in

D:\NT4\Install_Serial.exe, then click OK.

(Change D: to match your CD-ROM drive letter)

3. Click Next when the Welcome window appears.

4. Choose Install, then click Next.

5. Click Yes, then click Exit.

6. From the desktop click Start, then Run.

7. TypeinD:\NT4\Install_Parallel.exe, thenclickOK.

(Change D: to match your CD-ROM drive letter)

8. Repeat steps 3-5.

9. Click Yes to restart Windows to complete the

installation.

ToVerifyWindowsNT4.0Installation

1. Go to Start / Settings / Control Panel,double click

Ports device icon.

2. AnewCOMportwillbeassigned when successfully

installed.

3. Click Start, Programs, Administrative Tools,

Windows NT Diagnostics. Click Resources tab,

SIIGpar and SIIGser should be displayed.

Windows2000

1. At the Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended), and click Next.

3. Select Specify a location, uncheck the other boxes,

and click Next.

4. Insert the driver CD, type in D:\2000, then click OK.

(Change D: to match your CD-ROM drive letter)

5. Click Next and Finish.

6. Repeat steps 1-5 two more times.

7. Restart Windows to complete the installation.

32-bitWindowsXP/Server2003

1. At the Found New Hardware Wizard, insert the

driver CD.

For XP w/SP1 or earlier/ Server 2003: go to step #2.

For XP w/SP2 or later/Server 2003 wSP1 or later:select

No, not this time, click Next.

2. Select Install the software automatically

(Recommended,then click Next.

3. Click Finish.

4. Repeat steps 1-3 two more times.

5. Restart Windows to complete the installation.

64-bitWindowsXP/Server2003

1. At the Found New Hardware Wizard, insert the

driver CD.

For XP w/SP1 or earlier/ Server 2003: go to step #2.

For XP w/SP2 or later/Server 2003 wSP1 or later:select

No, not this time, click Next.

2. Select Install the software automatically

(Recommended,then click Next.

3. Click Continue Anyway, then click Finish.

4. Repeat steps 1-3 several more times.

5. Restart Windows to complete the installation.

ToVerifyWindows2000/XP/2003Installation

1. Right click My Computer, click Manage, then select

Device Manager.

2. Double click Ports (COM & LPT), CyberSerial PCI

16Cxxx... andCyberParallel PCI... should be

displayed.

3. Double click Multifunction adapters, SIIG

CyberPro 1S1P PCI board should be displayed.

WindowsVista™

1. At the Found New Hardware window, insert the

driver CD, click Locate and install driver software

(recommended), then click Continue.

2. Click Next, then click Close.

3. Repeat step #2 to complete the driver installation.

Note: Windows Vista driver installation process

may take several minutes to complete.

ToVerifyWindowsVistaInstallation

1. Right click Computer,click Manage,clickContinue,

then click Device Manager.

2. Click on the +(plus sign) in front of Ports (COM &

LPT), CyberSerialPCI16Cxxx... and CyberParallel

PCI... should be displayed.

3. Double click Multifunction adapters, SIIG

CyberPro 1S1P PCI board should be displayed.

Changing COM Port Address

Some serial devices need a specific COM port in order to

work. If your serial device works properly, do not

change this setting.

Windows95/98/98SE/ME

1. From the Device Manager window double click

Ports (COM & LPT), then double click CyberSerial

PCI... serial port.

2. Click Settings tab, at the Port Name box click the

down arrow and select a COM address that is not

currently in use.

3. Click OK, click OK again to close Device Manager

to save the changes.

Windows2000/XP/Server2003/Vista

1. From the Device Manager window double click

Ports (COM & LPT), then double click CyberSerial

PCI... serial port.

2. Click Settings tab and click Advanced....

3. At the COM Port number box, click the down arrow

and select a COM port that is not in use. Click OK.

4. Click OK, then close Device Manager to save the

changes.

Changing Parallel Port Address (LPT)

Some parallel devices need a specific parallel port in

order to work. If your parallel device works properly, do

not change this setting.

Windows95/98/98SE/ME

1. From the Device Manager window double click

Ports(COM &LPT),thendoubleclickCyberParallel

PCI.

2. Click Settings tab, check Enable use of I/O location

278h.

3. Click OK, click OK again to close Device Manager,

andclick Yes torestartWindowsto save thechanges.

Windows2000/XP/Server2003/Vista

1. From the Device Manager window double click

Ports(COM &LPT),thendoubleclickCyberParallel

PCI....

2. Click Port Settings tab.

3. At the LPT Port Number box, click the down arrow

and select an LPT port that is not in use.

4. Click OK, then close Device Manager to save the

changes.

Blank Page

Andere Handbücher für Cyber 1S1P PCI

Inhaltsverzeichnis

Andere SIIG PCI-Karte Handbücher

SIIG

SIIG DP CyberSerial PCI Bedienungsanleitung

SIIG

SIIG Low Profile PCI-1P Bedienungsanleitung

SIIG

SIIG SATA II-150 PCI Bedienungsanleitung

SIIG

SIIG 1394 PCI Adapter Bedienungsanleitung

SIIG

SIIG Cyber 1S1P PCI Bedienungsanleitung

SIIG

SIIG LB-GE0114-S1 Bedienungsanleitung

SIIG

SIIG NN-400M12-S6 Bedienungsanleitung

SIIG

SIIG DP CyberSerial Dual PCI RJ Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCIe Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Bedienungsanleitung

SIIG

SIIG JJ-P02012 Bedienungsanleitung

SIIG

SIIG NN-E38012-S2 Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

SIIG

SIIG PCI Express Serial Cards Bedienungsanleitung

SIIG

SIIG RS232 Serial Bedienungsanleitung

SIIG

SIIG DP CyberSerial 4S PCIe Bedienungsanleitung

SIIG

SIIG LB-US0314-S1 Bedienungsanleitung

SIIG

SIIG SoundWave 7.1 PCI Bedienungsanleitung

SIIG

SIIG Universal PCI Serial Cards Bedienungsanleitung

SIIG

SIIG CyberPro PCI 2S Bedienungsanleitung

SIIG

SIIG NN2630 Bedienungsanleitung

SIIG

SIIG Low Profile PCI-1S1P Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 4-Port PCI Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung

Alpha Networks

Alpha Networks WMP-A13V Bedienungsanleitung

Acqiris

Acqiris SA230E Bedienungsanleitung