Silver King SKBB69 Kurzanleitung

Specifications Subject to Change Without Notice.

1600 Xenium Lane North, Minneapolis, MN 55441-3787

Phone (763) 923-2441

Technical Manual

and

Replacement Parts List

Back Bar Coolers

MODELS

SKBB59

SKBB69

SKBB90

TECHNICAL MANUAL

SILVER KING PREPARATION TABLES

MODELS SKBB59, SKBB69, SKBB90

Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable

equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new

Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to validate your warranty.

INSPECT FOR DAMAGE AND UNCRATE

Upon delivery of your new Silver King unit, uncrate at once to inspect for possible freight damage following the instructions printed

on the exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for

any evidence of mishandling. Silver King is not responsible for any damages incurred during shipping. Save all packaging

materials if a claim is filed.

The back bar cooler was shipped on a skid. We recommend not removing the unit from the skid until it is as close as possible to the

desired end location.

INSTALLATION

The exterior surfaces of the cabinet have been protected by a plastic covering during manufacturing and shipping. This covering

can be readily stripped before installation. After removing this covering, wash the interior and exterior surfaces using a warm, mild

soapy water solution and a sponge or cloth, rinse with clean water and dry.

Location

When locating your new back bar refrigerator, convenience and accessibility are important considerations, but the following

installation guidelines must be followed;

•Always avoid placing the cooler adjacent to an oven, heating element or hot air source that would affect the operation of the

unit.

•For proper ventilation the cooler can be installed tight on the sides and back with the rear bumpers installed. The front must

be unobstructed.

•The unit must be level or tilted backwards slightly.

•If the unit is not on legs or casters it should be sealed to the floor with an NSF approved sealant to prevent water from getting

under the unit.

Shelves

Inside the cooler you will find Shelves and a bag containing Shelf Supports. The Shelf supports with the ‘tang’ install on the rear

pilasters. The shelf system allows for easy adjustment of shelf height to suit your needs.

Electrical Connections

Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to power. The

specifications on the data plate supersede any future discussion.

The standard back bar cooler is equipped with an eight (8) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase properly

grounded electrical receptacle. The power cord comes with a 3 prong plug for grounding purposes. Any attempt to cut off the

grounding spike or to connect to an ungrounded adapter plug will void the warranty, terminate the manufacturers responsibility and

could result in serious injury.

The circuit must be protected with a 15 or 20 ampere fuse or breaker. The unit must be isolated on a circuit and not plugged into an

extension cord.

OPERATION

Initial Start-Up

After satisfying the installation requirements, the back bar cooler is ready to start. The Compressor will start when the power cord is

connected to the required power source. If the Compressor does not start when the unit is initially plugged in, check to make sure

that the Temperature Control is not in the "off" position. Allow the unit to run for two hours before loading it with product. When

loading the unit with product, take care not to block the air flow in the cabinet as this would affect the units performance.

Temperature Control

The Temperature Control is located on the left end of the back wall of the cabinet interior and is factory set to maintain an average

cabinet temperature of approximately 36 to 40 Deg F. To obtain colder temperatures turn the Temperature Control stem clockwise

and vice versa. Allow the unit a minimum of one hour to respond to a control setting adjustment.

Defrost

Your Silver King bottle cooler is an automatic defrost unit and no additional plumbing is required. Automatic defrosting is

accomplished when frost buildup on the Evaporator Coil is cleared during Compressor "off" cycles. Defrost water is collected in a

pan located in the compressor compartment where it is evaporated into the room air. It is important that the unit be installed level to

allow proper drainage of the defrost water.

Light

The on / off switch for the interior light is located in the cabinet interior under the light near the doors.

MAINTENANCE

Preventative maintenance is minimal although these few steps are very important to continued operation and maximizing the life of

the appliance.

Cabinet Surfaces

The interior and exterior surfaces should be cleaned periodically with a solution of warm water and mild soap, rinsed and wiped dry

with a soft cloth. A good stainless steel cleaner can also be used on the stainless steel surfaces. Should a surface become

stained, do not attempt to clean with an abrasive cleanser or scouring pad. Use a soft cleanser and rub with the grain of the metal

to avoid scratching the surface. Do not use chlorinated cleaners. Always rinse well and dry after cleaning. To help remove odors,

the interior surfaces of the unit should be periodically cleaned with a solution of baking soda and warm water.

Condenser

Periodically the Condenser must be cleared of dust. The Condenser is located behind the front grill on the cabinet. To clean the

Condenser simply remove the front grill and brush or vacuum the exposed condenser fins. This will need to be done regularly to

maintain proper performance and increase the life of the unit.

Drain Pan

The Drain Pan is located under the front grill and can be removed by pulling is out the front of the unit. Depending on local

conditions the Drain Pan may need to be periodically emptied and cleaned.

Door Gasket

The Door Gasket will collect dirt and should be wiped clean with a warm, mild soapy water solution to extend its life and assure

maximum cabinet performance and life.

MODEL SERIAL NO. DATE INSTALLED

ITEM

NUMBER

DESCRIPTION

PART NUMBER

SKBB59

PART NUMBER

SKBB69

PART NUMBER

SKBB90

GRILL, FRONT (BLACK) 29425 29425 29425

GRILL, FRONT (STAINLESS) 30399 30399 30399

GRILL, REAR (BLACK) 29410 29410 29410

GRILL, REAR (STAINLESS) 29731 29731 29731

3 CONDENSER COVER 29004 29004 29004

4 CONDENSER COIL 26530 26530 26531

5 CONDENSER FAN MOTOR 115V 23921 23921 23921

6 CONDENSER FAN BLADE 30613 30613 30613

7 CONDENSER FAN MOTOR BRACKET 41450 41450 41450

8 COMPRESSOR KIT (W/ ELECTRICALS & DRIER) 115V 10343-41 10343-41 10343-41

9 COMPRESSOR ELEC. KIT (RELAY/OVERLOAD/CAPACITOR) 115V 10344-41 10344-41 10344-41

10 DRIER 22677 22677 22677

11 CONDENSATE DRAIN PAN 29457 29457 29457

12 POWER CORD 115V 43263 43263 43263

13 EVAPORATOR COIL 26532 26745 26533

14 HEAT EXCHANGER (NOT SHOWN) 29799 29799 29799

15 EVAPORATOR FAN MOTOR BRACKET 24494 24494 24494

16 EVAPORATOR FAN MOTOR 115V 21251-2 21251-2 21251-2

17 EVAPORATOR FAN BLADE 22943 22943 22943

18 EVAPORATOR FAN GUARD 41473 41473 41473

19 TEMPERATURE CONTROL 24089 24089 24089

20 BUSHING HINGE 99711 99711 99711

21 DOOR GASKET (SOLID DOOR) 29263 29263 29263

HINGE, TOP LEFT (SOLID DOOR) 29280 29280 29280

HINGE, TOP LEFT (GLASS DOOR) 26708 26708 26708

HINGE, BOTTOM LEFT (SOLID DOOR) 29274 29274 29274

HINGE, BOTTOM LEFT (GLASS DOOR) 26710 26710 26710

HINGE, TOP RIGHT (SOLID DOOR) 29269 29269 29269

HINGE, TOP RIGHT (GLASS DOOR) 26714 26714 26714

HINGE, BOTTOM RIGHT(SOLID DOOR) 29283 29283 29283

HINGE, BOTTOM RIGHT (GLASS DOOR) 26712 26712 26712

DOOR, RIGHT HAND (SOLID, BLACK) 10335-22 10335-22 10335-22

DOOR, RIGHT HAND (GLASS) 26718 26718 26718

DOOR, RIGHT HAND (SOLID, STAINLESS) 10335-23 10335-23 10335-23

DOOR, LEFT HAND (SOLID, BLACK) 10335-24 10335-24 10335-24

DOOR, LEFT HAND (GLASS) 26722 26722 26722

DOOR, LEFT HAND (SOLID, STAINLESS) 10335-25 10335-25 10335-25

28 DOOR HANDLE (SOLID DOOR) 29261 29261 29261

29 DRAIN 24302 24302 24302

30 THRESHOLD GUARD 29173 29173 29173

31 SHELF 26730 26731 27626

32 PILASTER 22491 22491 22491

33 SHELF SUPPORT, WITH TANG 99531 99531 99531

34 SHELF SUPPORT 99530 99530 99530

35 LAMP SWITCH 26378 26378 26378

36 LAMP SOCKET 21121 21121 21121

37 LAMP STARTER 21124 21124 21124

38 LAMP BALLAST 21120 21120 21120

39 BUMPER 23927 23927 23927

40 LATCH/ STRIKE ASSY 30640 30640 30640

REPLACEMENT PARTS LIST – MODELS SKBB59, SKBB69, SKBB90

FOR EQUIPMENT WITH SERIAL NUMBERS STARTING WITH ‘S’ ONLY

WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS

FORM NO. 29490 REV F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Silver King Zubehör Handbücher

Silver King

Silver King SKBC65 Kurzanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung