Silver King SKBC65 Kurzanleitung

Specifications Subject to Change Without Notice.

1600 Xenium Lane North, Minneapolis, MN 55441-3787

Phone (763) 923-2441

Technical Manual

and

Replacement Parts List

Horizontal Bottle Coolers

MODELS

SKBC50

SKBC65

SKBC95

TECHNICAL MANUAL

SILVER KING PREPARATION TABLES

MODELS SKBC50, SKBC65, SKBC95

Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable

equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new

Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to validate your warranty.

INSPECT FOR DAMAGE AND UNCRATE

Upon delivery of your new Silver King unit, uncrate at once to inspect for possible freight damage following the instructions printed

on the exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for

any evidence of mishandling. Save all packaging materials if a claim is filed.

INSTALLATION

The exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping. This covering can be

readily stripped before installation. After removing this covering, wash the interior and exterior surfaces using a warm, mild soapy

water solution and a sponge or cloth, rinse with clean water and dry.

Location

When locating your new bottle cooler, convenience and accessibility are important considerations, but the following installation

guidelines must be followed:

•Always avoid placing the bottle cooler adjacent to an oven, heating element or hot air source that would affect the operation

of the unit.

•For proper ventilation the bottle cooler can be installed tight on the sides and back with the rear bumpers installed.

•The top and front must be unobstructed.

•The unit must be level or tilted backwards slightly.

•If the unit is not on legs or casters it should be sealed to the floor with an NSF approved sealant to prevent water from getting

under the unit.

Dividers

The bottle cooler comes with dividers to aid in separating stock. The spacing of the dividers is adjustable to suit various needs.

The ends of the dividers fit into the mounting brackets on the front and rear of the liner. An additional hold-down bracket mounted to

the top front mounting bracket holds them in place. This bracket must be removed using a Phillips screwdriver in order to install or

adjust the spacers.

Electrical Connections

Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to power. The

specifications on the data plate supersede any future discussion.

The standard refrigerator is equipped with an eight (8) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase properly

grounded electrical receptacle. The power cord comes with a 3-prong plug for grounding purposes. Any attempt to cut off the

grounding spike or to connect to an ungrounded adapter plug will void the warranty, terminate the manufacturers responsibility and

could result in serious injury.

The circuit must be protected with a 15 or 20 ampere fuse or breaker. The unit must be isolated on a circuit and not plugged into an

extension cord.

Initial start up

After satisfying the installation requirements, the bottle cooler is ready to start. The Compressor will start when the power cord is

connected to the required power source. If the Compressor does not start when the unit is initially plugged in, check to make sure

that the Temperature Control is not in the "off" position. Allow the unit to run for two hours before loading it with product. When

loading the unit with product, take care not to block the airflow in the cabinet as this would affect the unit’s performance.

Temperature Control

The Temperature Control is located on the back wall of the cabinet liner and is factory set to maintain an average cabinet

temperature of approximately 36 to 40 Deg F.. To obtain colder temperatures turn the Temperature Control stem clockwise and

vice versa. Allow the unit a minimum of one hour to respond to a control setting adjustment.

Defrost

Your Silver King bottle cooler is an automatic defrost unit and no additional plumbing is required. Automatic defrosting is

accomplished when frost buildup on the Evaporator Coil is cleared during Compressor "off" cycles. Defrost water is collected in a

pan located in the compressor compartment where it is evaporated into the room air. It is important that the unit be installed level to

allow proper drainage of the defrost water.

MAINTENANCE

Preventative maintenance is minimal although these few steps are very important to continued operation and maximizing the life of

the appliance.

Cabinet Surfaces

The interior and exterior surfaces should be cleaned periodically with a solution of warm water and mild soap, rinsed and wiped dry

with a soft cloth. A good stainless steel cleaner can also be used on the stainless steel surfaces. Should a surface become

stained, do not attempt to clean with an abrasive cleanser or scouring pad. Use a soft cleanser and rub with the grain of the metal

to avoid scratching the surface. Do not use chlorinated cleaners. Always rinse well and dry after cleaning. To help remove odors,

the interior surfaces of the unit should be periodically cleaned with a solution of baking soda and warm water.

Condenser

Periodically the Condenser must be cleared of dust. The Condenser is located behind the front grill on the cabinet. To clean the

Condenser simply remove the front grill and brush or vacuum the exposed condenser fins. This will need to be done regularly to

maintain proper performance and increase the life of the unit.

Drain Pan

The Drain Pan is located under the front grill and can be removed by pulling is out the front of the unit. Depending on local

conditions the Drain Pan may need to be periodically emptied and cleaned.

MODEL SERIAL NO. DATE INSTALLED

ITEM

NUMBER DESCRIPTION PART NUMBER

SKBC50

PART NUMBER

SKBC65

PART NUMBER

SKBC95

GRILL, FRONT (BLACK) 29000 29000 29000

GRILL, FRONT (STAINLESS) 29985 29985 29985

GRILL, REAR (BLACK) 29410 29410 29410

GRILL, REAR (STAINLESS) 29731 29731 29731

3 CONDENSER COVER 29686 29686 29686

4 CONDENSER COIL 26530 26530 26531

5 CONDENSER FAN MOTOR 115V 23921 23921 23921

6 CONDENSER FAN BLADE 30613 30613 30613

7 CONDENSER FAN MOTOR BRACKET 41450 41450 41450

8 COMPRESSOR KIT (W/ ELECTRICALS & DRIER) 115V 10343-41 10343-41 10343-41

9 COMPRESSOR ELEC. KIT (RELAY/OVERLOAD/CAPACITOR) 115V 10344-41 10344-41 10344-41

10 DRIER 22677 22677 22677

11 CONDENSATE DRAIN PAN 29457 29457 29457

12 POWER CORD 115V 43263 43263 43263

13 EVAPORATOR COIL 26532 26745 26533

14 HEAT EXCHANGER (NOT SHOWN) 29794 29794 29794

15 EVAPORATOR FAN MOTOR BRACKET 24494 24494 24494

16 EVAPORATOR FAN MOTOR 115V 21251-2 21251-2 21251-2

17 EVAPORATOR FAN BLADE 99196 99196 99196

18 EVAPORATOR FAN GUARD 41473 41473 41473

19 TEMPERATURE CONTROL 20889 20889 20889

20 DOOR GUIDE 29463 29463 29463

21 AIR DEFLECTOR 29012 29564 30829

22 CENTER MULLION 29003 30827 30828

23 DOOR 10335-26 10335-27 10335-27

24 DOOR HANDLE 28788 28788 28788

25 SCREW HANDLE 29456 29456 29456

BOTTLE CAP DEFLECTOR (BLACK) 43675 43675 43675

BOTTLE CAP DEFLECTOR (STAINLESS) 29468 29468 29468

27 BOTTLE CAP OPENER 99972 99972 99972

BOTTLE CAP CATCHER (BLACK) 43674 43674 43674

BOTTLE CAP CATCHER (STAINLESS) 29986 29986 29986

29 SHOULDER SCREW - CAP CATCHER 30432 30432 30432

30 DIVIDER 28734 28734 28734

31 BUMPER 23927 23927 23927

32 LATCH / STRIKE ASSY 30640 30640 30640

REPLACEMENT PARTS LIST – MODELS SKBC50, SKBC65, SKBC95

FOR EQUIPMENT WITH SERIAL NUMBERS STARTING WITH ‘S’ ONLY

WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS

FORM NO. 29470 REV F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Silver King Zubehör Handbücher

Silver King

Silver King SKBB69 Kurzanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung