Sirius Satellite Radio ALFRESCO SL83 Bedienungsanleitung

SL83 ALFRESCO RANGEHOOD

ONBOARD INSTALLATION INSTRUCTIONS

Congratulations on your purchase!

Thank you for choosing a Sirius product.

SL83 FRESCO 1200 EAN #9351116001155

SL83 BBQ 1200M EAN #9351116001209

SL83 FRESCO 1500 EAN #9351116001223

www.siriusbrand.com

The symbol on the product or on its packaging indicates that this product

may not be treated as house-hold waste. Instead it shall be handed

over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about

recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the

product. This appliance is marked according to the European directive

2002/96/EC on waste electrical and electronic equipment (WEEE).

Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory

such as flexible ducting, Sirius will only warrant the rangehood and motor. If installation is found to be

the cause of failure or issue then charges will apply for service and parts.

Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to

increase noise levels, increase vibration and reduce airflow. Sirius Semi-rigid or solid ducting can be

used in lieu. There is a range available to suit any application.

Ducting available at www.siriusbrand.com

6 Year Warranty when Sirius Ducting is used. Full replacement warranty on parts and labour.

See website for terms & conditions.

A reduction in the duct diameter from stated ducting size will void warranty.

If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to installation

WARNING

The appliance must be installed and

connected to the power supply only by a

qualified technician.

• There should be adequate ventilation of the room when the rangehood is used at the same time as

appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the

room)

• The details concerning the method and frequency of cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions;

• Do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.

BEFORE YOU INSTALL - DUCTING INFORMATION

A comprehensive list of 300mm ducting components for

the SL83FRESCO1500 are available at siriusbrand.com

or contact your nearest retail partner.

Min. 1200mm - Max. 1600mm distance for

barbecues.

If the rangehood is positioned above the max height

recommended, warranty may be compromised

as performance of the rangehood will be affected.

Measurement is taken from the top of the grills to the

underside of the hood. (Fig.1)

• The air being drawn can’t be conveyed through

or into a duct used to let out fumes from

appliances fed by energy other than electric

power (eg. centralized heating, radiators, water

heaters, etc.).

• Attention: remove any possible PVC film from the

stainless steel, including the filters.

• To externally vent, please comply with the

pertaining rules given by competent authorities.

• Provide the room with an adequate ventilation

when a rangehood and appliances fed by energy

other than electric power (gas, oil, or coal stoves,

etc.) are used simultaneously. The rangehood,

when evacuating the air, could generate a

negative pressure in the room which can’t exceed

the limit of 0.04 mbar, in order to avoid the

suck of exhausts deriving from the heat source.

Therefore the room should be provided with air

intakes to allow a constant flow of fresh air.

If the rating label in the rangehood shows the symbol

, the appliance is built in class II° and it does not

need any earth connection.

If the rating label in the rangehood does not show

the symbol , the appliance is built in class I° and it

needs the earth connection.

When performing the electrical connections on the

appliance, please make sure that the current-tap

is provided with earth connection and that voltage

values correspond to those indicated on the label

placed inside the appliance itself.

Before carrying out any cleaning or maintaining

operations, the appliance needs to be switched off.

If the appliance is not provided with a non-separable

flexible cable and plug, or with another device

When ducting rangehood, options are as follows:

Roof vent - EASYROOF 200T/M

*Kit includes roof flashing

Download installation guide

Eave vent - EASYEAVE 200

Download installation guide

Wall vent - EASYWALL 200

Download installation guide

ensuring omnipolar disconnections from the grid,

with an opening distance between the contacts of at

least 3mm, then such disconnecting devices must be

supplied within the fixed installation.

If the fixed appliance is endowed with a supply cord

and a plug, the appliance has to be put in a place

where the plug can be reached easily.

The use of materials which can burst into flames

should be avoided in close proximity of the appliance.

When frying, please pay particular attention to fire

risk due to oil grease. Being highly flammable, fried

oil is especially dangerous. Do not use uncovered

electric grills. In order to avoid possible fire risk, all

instructions for grease-filter cleaning and for removing

eventual grease deposits should be strictly followed.

WARNING

Min. 1200 - Max. 1600

(Fig. 1)

(Fig. 2a)

(Fig. 2b)

(Fig. 2c)

Dome

featured on

200mm kit

only

FRONT VIEW

1. The rangehood is quite heavy, so two people

will be needed for installation.

2. Before connecting any ducting to the motor,

make sure the non-return valves - which are on

the air outlet of the motor - can swing open.

3. Using the supplied bracket template (pg. 10),

mark the location of the holes that need to be

drilled in the wall, being careful to make sure

that the wall behind is clear of electrical wiring,

plumbing, pipes etc. Note: Be sure to set the

height of the rangehood between the minimum

and maximum height requirements as per

diagram Fig. 1 (Pg. 3). This can be done by

measuring from the lowest point of the rangehood

to the horizontal support bar. (1200mm

rangehood - Fig. 4a.

1500mm rangehood Fig. 4b.)

NOTE: Model measurements will vary.

Please check specific model specs.

4. Using an 8mm drill bit, pre-drill the holes that

will hold the brackets to the wall. (Using bracket

template).

SL83 FRESCO RANGEHOOD

INSTALLATION - ONBOARD MOTOR

Before installing the appliance, make sure that

none of the parts are damaged in any way. In

case of damaged parts, contact your retailer

and do not proceed with installation. Read all

of the following instructions with care before

installing the appliance.

• Use ducting within the min/max specifications

• Limit the number of ducting bends.

• Do not make any changes in ducting diameter:

Must be Ø 200 mm or equal surface area for

1200mm rangehoods, Ø 300mm for 1500mm

rangehoods)

Before installing the appliance - in order not to

damage the appliance itself - the metal grease filter

should be removed. These filters could be removed

by pushing the handles towards the back side of the

rangehood and pulling it downwards to unfasten it

from its slot. (Fig.3).

NOTE

CAUTION

WARNING

WARNING: Failure to install the screws or fixing

device in accordance with these instructions

may result in electrical hazards.

To install the appliance please follow these

instructions:

• The appliance must be installed by qualified

technicians, or where possible use a Sirius

recommended installer. See siriusbrand.com.

In order to avoid damage to the electronic parts

of the appliance, please do not use additional

screws.

1. Prepare the power supply - 240 volts.

2. Prepare a hole for the exhaust (Ø 210mm for

1200, Ø 310mm for 1500mm).

• Maximum length of ducting should not exceed

7 metres.

• Do not use screws to fix the ducting to the

rangehoods as they will prevent the movement of

non-return valves.

• Limit the number of elbows in the ducting, since

each elbow reduces the duct efficiency by 1

metre. (i.e. if you use two 90° elbows, the length

of ducting must not exceed 5 metres.)

• Avoid abrupt direction changes.

• Use constant diameter ducting for the whole

length for this rangehood (Ø 200mm ducting for

1200, Ø 300mm ducting for 1500mm).

• The use of Sirius ducting will increase the

warranty of the unit to 6 years.

(Fig. 3a)

(Fig. 3b)

5. Insert the supplied plastic dowels to the

pre-drilled holes and fix bracket to the wall with

the supplied screws. (Note: Please use a spirit

level to make sure the bracket is perfectly level.)

6. Once the bracket is secure, using two people,

lift the hood and drop the horizontal support bar

onto the fixed bracket (Fig. 5).

(Note: There are additional holes on the inside of

the hood to secure the rangehood flush to the wall

and completely stable. (Hole locations will vary per

model.)

(1200mm rangehood Fig. 4a)

(1500mm rangehood Fig. 4b)

(Fig. 5)

• Accurate maintenance guarantees good

functioning and long-lasting performance.

• Particular care is due to the grease filters.

They can be removed by pushing its handle

toward the back side of the rangehood and

pulling the filter downwards so to unfasten it from

its slot (Fig.3).

To insert the filter just perform the opposite

operation.

• After 30 hours of operation, the push button

control panel will flash, signaling the filters are due

for cleaning. Press the timer button to reset.

The grease filter needs cleaning by regular

handwashing or in dishwashers every two

months at least, depending on its use.

• Filters may require cleaning sooner if

frequent heavy cooking is done.

• To clean the appliance itself, water and detergent

are recommended, while abrasive products

should be avoided. For steel appliances

specialized detergents are recommended (please

follow the instructions indicated on the product

itself to obtain the desired results).

MAINTENANCE

Manual control buttons:

SL83 FRESCO 1200

SL83 BBQ 1200M

SL83 FRESCO 1500

A: Light switch on/off

B: Motor switch on speed 1/off - (low/simmer)

C: Motor switch on speed 2 - (general cooking)

D: Motor switch on speed 3 - (high power)

E: Motor switch on speed 4 - (booster)

F: 10 minute shut-off timer

OPERATION

10. Fix the two flue cover brackets to the rear wall

and ceiling using the 4 x 30mm screws supplied.

11. Telescope the flue cover up into position in

line with the brackets and secure in place with

supplied 10mm screws (Fig 6).

7. Connect your Sirius ducting

(see www.siriusbrand.com for approved

ducting) to the outlet collar on the rangehood and

secure in place with a ring clamp if you are using

semi rigid ducting. If you are using solid/rigid

ducting, an external duct connector is required.

(Note: do not fix the ducting in place with screws

as they will prevent the movement of the non-

return valves). (See Fig. 2 for ducting options).

Complete all of the duct work to the atmosphere

before fixing the flue covers in place to ensure the

ducting has not come free.

8. Insert the upper flue cover into the lower flue

cover and mount into the channel on the top of

the rangehood.

9. Telescope the upper flue cover to the ceiling and

mark with a pencil the outer line of the cover, this

will give you the exact location of where the top

fixing brackets need to be fitted to the ceiling.

NOTE

Please do not fix shroud permanently.

Must be removable for servicing purposes.

(Fig. 6)

Working:

6 channel control for rangehood remote.

• When the rangehood is first turned on, hold the

lighting button for 5 seconds.

RC001 - RADIO CONTROL

Radio control used for the remote operation of

rangehoods.

TECHNICAL DATA

• Alkaline battery powered: 12 V mod. 23 A

• Operating frequency: 433.92 Mhz

• Combinations: 32.768

• Max. consumption: 25 mA

• Operating temperature: -20 ÷ + 55 °C

• Dimensions: 120 x 45 x 15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons for cooker

hood management, as specified below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control unit

ready to be used with codes preset in the factory.

REMOTE CONTROL OPERATION MODE

Standard configuration:

Standard configuration requires all rangehood radio

control systems to be provided with the same

transmission code. In the event two rangehoods are

installed in the same room or nearby, each system

may affect the operation of the another. Therefore,

the code of one radio control system must be

changed.

Generating a new transmission code:

The radio control system is provided with preset

codes. Should new codes be required, proceed as

follows: Press simultaneously buttons:

for two seconds. When LEDs are on, press buttons:

(within 5 seconds). The LEDs flashing 3 times

indicate the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Learning the new transmission code.

Once the transmission code is changed in the radio

control unit, the electronic central unit of the cooker

hood must be made to set the new code in the

following way:

Press the main power-off button of the hood and

then restore power to the electronic control unit.

Within the next 15 seconds, press the Light Button to

synchronise the central unit with the code.

Reset of the Factory configuration:

To restore the Factory configuration, follow the

procedure described below: press simultaneously

buttons:

for 2 seconds. When LEDs light on, press buttons:

(within 5 seconds). LEDs flashing 6 times in-dicate

the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Emergency button:

In the event that the radio control does not work, use

the emergency button to switch the appliance off.

After any necessary repairs have been performed,

reset the emergency button.

SL83 FRESCO 1200 WIRING DIAGRAM

SL83 FRESCO 1500 WIRING DIAGRAM

BRACKET TEMPLATE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC93 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Essence S-DD 16 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Handbuch

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT976 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SLEM80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1 Benutzerhandbuch

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLEM83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL909 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT966 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD2-L TC Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2ELEMIC58 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 L 1500 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch